Specifications DAEWOO Electronics Multi Use Upright Series Model Rating Watts Weights(Net) Dimension (LxWxH) Cord Length Inner Filter Exhaust Filter Head Light Belt Agitator RCU- 300R AC 220 V / 50 Hz Max. 2000W 9.
Components Desription & Assembling Main Power Switch Nozzle Power Switch HANDLE ( Grip + Pipe ) Pipe Extension Button HOSE DUST CUP Hose Clip BODY Height Adjustment Lever Cord Storage Thermal Reset Button Remove Button for Nozzle Release Pedal Head Light NOZZLE Cord Plug DUSTING BRUSH PEDAL BRUSH CREVICE NOZZLE UPHOLSTERY NOZZLE
HOSE GUIDE & HOSE ASSEMBLING ● HOSE GUIDE assembling - Set HOSE GUIDE on the top of the cleaner - Screwing a screw with the "+" shape screw driver HOSE ● HOSE AS assembling - Insert the body side of HOSE AS in the hose hole of the cleaner. - Caution : Insert the protrusion of HOSE end through "▲" mark in side of the hose hole If connected the HOSE and the BODY, The HOSE can not be removed from the BODY. If need the disassembling it, call the A/S center.
Using Guide & Converting to Canister Type UPRIGHT USING STATE ● Push the RELEASE PEDAL and rotate the BODY as below the picture. - Set HOSE GUIDE on the top of the cleaner - Causion : If the power switch is not ON, though the brush switch is ON the NOZZLE is not work. If this cleaner is not in the using state, though the power and the brush switch are ON, the NOZZLE is not work because of the safty device(NOZZLE SAFTY SWITCH).
ACCESSORIES USING ● To use all ACCESSORIES, Connect them to HOSE end. - Causion : When use accessories, if air Inlet is narrow unexpectly, HOSE length can be decreased and the cleaner can be come down. NOZZLE HEIGHT CONTROL KEEPING ● Rotate the HEIGHT ADJUSTMENT LEVER for the carpet surface to clean.
Cleaning Dust Cup & Replacement Filters DISASSEMBLING DUST CUP & EXHAUST FILTER ● Set OFF the Cleaner. ● Grasp the DUST CUP LEVER and pull out the DUST CUP from BODY. ● Pull out the EXHAUST FILTER EXHAUST FILTER BODY Dust Cup Lever DUST CUP EMPTY DUST CUP ● If dust filled up at the height of the "FULL" line in the DUST CUP or FULL CUP LAMP light on. or FULL CUP INDICATOR light on. ● Move the DUST CUP at the garbage. ● Push the DUST REMOVE BUTTON and the dust drop automatically.
INNER FILTER CLENING AND REPLACING ● Lift up the DUST CUP COVER and rotate and remove the INNER FILTER ● Tapping it to remove the dust at the pleats of it as below picture. - Caution : This INNER FILTER is not washable. After tapping it, assemble it and use cleaner When tapping, be careful not to damage the filter media. Replace the new INNER FILTER in every a year. ▷ INNER FILTER TYPE No.
Replacing Belt & Nozzle Head Light REPLACING BELT OF AGITATOR BRUSH ● Turn OFF the cleaner. ● Remove the BOTTOM PLAE of NOZZLE. ( unscrewing 5 screws with "+" shape screw driver. ) ● Set the new BELT over Motor Pully. ● Hang the AGITATOR BRUSH into the BELT and assemble the AGITATOR BRUSH. ● Cover the BOTTOM PLATE and secure the 5 srcews - Warnig : Before replacing the BELT. Check the disconnecting the cleaner from the electrical outlet. ▷ BELT TYPE No.
Please check each item below if you have trouble with your cleaner. Before checking, ensure that the cleaner is unplugged from the power supply. Problem Cleaner won't run Check Point Note 1. Power cord not firmly plugged into outlet. 1. Plug unit in firmly. 2. Motor protector tripped. 2. Cool down and press the RESET BUTTON ( See 2 page) 3. Need service. 3. Take to service center or call XXXX-XXXX. No power at rotating the AGITATOR 1. Cleaner is not the upright using stat 1.
Trouble Shooting Please check each item below if you have trouble with your cleaner. Before checking, ensure that the cleaner is unplugged from the power supply. Problem Cleaner won't run Check Point Note 1. Power cord not firmly plugged into outlet. 1. Plug unit in firmly. 2. Motor protector tripped. 2. Cool down and press the RESET BUTTON ( See 2 page) 3. Need service. 3. Take to service center or call XXXX-XXXX. No power at rotating the AGITATOR 1. Cleaner is not the upright using stat 1.
