USER’S GUIDE COLOR MONITOR Model No :L710/L710M
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 INTRODUCTION This manual explains how to correctly install, operate and get the best performance from your monitor.
SETUP PRODUCT FEATURES CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD The monitor is designed for use in a small work area or for those who need more work space on the desk. The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. The monitor supports a safe working environment in strict compliance with the TCO 99 standard for low emissions .
OPERATION & ADJUSTMENT CONTROL PANEL < L710M > < L710 > 1 POWER Shows both normal operation and power management status with power indicator light. Swithes the monitor on and off. Shows both normal operation and power management status with power indicator light. Swithes the monitor on and off. 2 POWER Indicator 1 POWER 2 POWER Indicator 5 5 4 8 2 8 3 7 6 1 3 4 (*) Moves cursor to the right or low window in the OSD window and increases the value of any selected function.
KEY PROCESS ADJUSTMENT PROCEDURE MENU 1280X1024 64K U T L TY 60 OSD No Is the H.Size proper? U T L TY Adjust the CLOCK control. OSD SELECT SELECT EXIT EXIT Yes U T L TY SH AR PN ESS Is the noise displayed on the screen? SH AR PN ESS Perform the AUTO POSITION. No EXIT Yes OSD OFF Perform the AUTO TRACKING.
OSD FUNCTIONS ICON CONTROL FUNCTION ICON CONTROL FUNCTION LANGUAGE Select language for OSD (6 languages). OSD TIME OUT Adjust the display OSD Menu. CLOCK Adjust the width (horizontal size) of the screen image. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp.
SPECIFICATIONS SELF DIAGNOSIS Panel If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is No Signal, Out of range or None support . No Signal screen is displayed when the DSub signal connector is connected but the status of the monitor is on DPMS mode. Synchronization Out of Range screen is displayed when the applied frequency is under or over normal range.
FACTORY PRESET TIMINGS CHANGING THE STAND VESA MODES VGA Resolution (dots X lines) 640 X 480 a 60Hz VGA Mode Removing Original Stand H.Freq (KHz) V.Freq (Hz) Remark 31.5 60 Non-interlaced 640 X 480 a 72Hz 37.9 72 Non-interlaced VGA 640 X 480 a 75Hz 37.5 75 Non-interlaced SVGA 800 X 600 a 56Hz 800 X 600 a 60Hz 35.2 56 Non-interlaced 37.9 60 Non-interlaced 800 X 600 a 72Hz 800 X 600 a 75Hz 48.1 72 Non-interlaced SVGA 46.9 75 Non-interlaced XGA 1024 X 768 a 60Hz 48.
TROBLESHOOTING Attaching the monitor with the arm-stand(option) Symptom Support stand Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Surface for stand installation Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Tighten up screws at the locations indicated by arrows.
Symptom No sound. Check Check the audio cable are correctly connected to the computer. Adjust the volume after checking the sound is muted. Check the audio system in the computer. Low sound. Adjust the volume on the OSD Menu. Adjust the volume of the sound card in the computer.
