Service Manual 38 / 48 / 51 Cm Mono Colour Television CHASSIS : CP-370 MODEL : 14Q1/20Q1/21Q1 14Q2/20Q2/21Q2 14Q3/20Q3/21Q4 14T1/20T1/21T1 14T2/20T2/21T2 14T3/20T3 ÀÀ @@ ,, DAEWOO ELECTRONICS CO., LTD.
CONTENTS Specifications ................................................................................................................ 1 Safety Instruction ......................................................................................................... 2 Circuit block Diagram ................................................................................................. 3 Alignment Instructions ...............................................................................................
Specifications Q : 1SPEAKER MODEL, T : 2SPEAKER MODEL VM : WITHOUT TXT. MODEL, TM : WITH TXT. MODEL TV Standard PAL/SECAM-B/G, D/K, I, H, NTSC-3.58/4.43 Mains Voltage 100~250V AC, 50/60Hz Power Consumption 14”Q = 69W, 14”T = 74W 20”Q = 79W, 20”T = 84W 21”Q = 79W, 21”T = 84W Sound output . 1 Speaker : 3W( at 80% MOD. 10% THD) . 2 Speaker : 4W + 4W( at 80% MOD. 10% THD) Speaker . 1 Speaker : 3W, 16 ohm . 2 Speaker : 7.
Safety Instruction WARNING: Before servicing this chassis, read the “X-RAY RADIATION precaution”, “safety precaution” and “product safety notice” below. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION.To avoid such hazards, the high voltage must not exceed the specified limit. The nominal value of the high voltage of this receiver is 22-23kv(14”), 2526kv(20”, 21”) at max beam current. The high voltage must not, under any circumstances, exceed 27.
Alignment Instructions 1. AFT 1.1 Standard B/G,D/K,I 1) Set a Signal Generator with - RF FREQUENCY = 38.9 MHz, - RF OUTPUT LEVEL = 80 5 dBuV - System = PAL / SECAM - B/G, D/K, I NTSC - 3.58/4.43 2) Connect the Signal Generator RF Output to P101 (Tuner IF Output). There must be no signal input to the tuner. 3) Press the “AFT” KEY and wait until the TV screen display “AFT OK”. 2. AGC 1) Set a Pattern Generator with RF LEVEL 63° 2 dBuV . 2) Connect a OSCILLOSCOPE PROBE to P102 (TUNER AGC INPUT).
. GEOMETRY 6.1 VERTICAL CENTER 1) Set the TV to NOR I mode. 2) Pressing the V-SIZE UP/DOWN KEY, the lower half of the screen is blanked. 3) Adjust the border line of blanked picture coincident with the mechanical center marks of the CRT using the V-CENTER UP/DOWN KEY. 6.2 VERTICAL SIZE The VERTICAL CENTER adjustment has to be done in advance. 1) Apply a RETMA PATTERN signal. 2) Set the TV to NOR I mode. 3) Adjust the upper part of the picture with the V-SIZE UP/DOWN keys. 6.
If EEPROM(1703) has been changed ; - Option data has to be changed and - all alignment function has to be readjusted.
IC Description DW370ASM* (Micro-controller for Non-Teletext Model) =TMS370C08A05 ( TI Type No.) (1) General Description The TMS370C08A05 devices are members of the cMCU370 family single-chip microcontrollers. The cMCU370 family provides cost effective real-time system control through use of the PRISM methodology. The PRISM methodology modular fabrication process integrates analog, digital, linear and power technologies on a single chip, thereby maximizing the total integration strategy.
• 09 CMOS Compatible I/O Pins - All Peripheral Function Pins Software Configurable for Digital I/O - 6 Bidirectionals, 3 Input Pins • Plastic 42 YSDP Pins Package (3) Block Diagram 8
DW5255M*(Micro-controller & West/East Teletext Decoder) DW5255RM*(Micro-controller & Cyrillic Teletext Decoder) =SDA5255-A*** (SIEMENS Type No.) (1) General Description The TDA5255 contains a slicer for VPS and TTX, an accelerating acquisition hardware module, a display generator for “LEVEL 1” TTX data and a 8 bit u-controller running at 333 nsec cycle time.
• Controller: - 8 bit configuration - 18 MHz internal clock - 0.
(4) Pin Description * A : DW5255M*/DW5255RM*, *B : DW370ASM* Pin Name A* B* A* B* 1 1 P3.1 T1IC1/CR Symbol SYS Description A* B* NTSC OUT for switching SAW filter K6259 - PAL/SECAM : L - NTSC : H 2 2 P0.7/Open Drain A0 BUSSTOP I2C BUS STOP IN for Computer controlled alignment in Factory ( Active Low ) 3 3 P0.6/Open Drain A1 SDA Serial data IN/OUT for I2C 4 4 P0.5/Open Drain A2 SCL Serial clock IN/OUT for I2C 5 5 P0.4/Open Drain A3 OPTION #5 #6 Teletext 6 6 P0.
Pin A* Name B* A* 30 CVBS 31 P2.3/8 bit ADC B* Symbol CVBS Description A* B* CVBS IN Not Used 32 22 P2.2/8 bit ADC B0/AN0/ADC AGC IF AGC INPUT for Auto Tuning System 33 23 P2.1/8 bit ADC B1/AN1/ADC KS Local KEY SCAN IN 34 24 P2.0/8 bit ADC B2/AN2/ADC S/SW Not Used 35 25 VSS VSS-OSD VSS Ground 36 26 P3.
24LC08B (EEPROM) (1) Features • Single supply with operation down to 2.5V • Low power CMOS technology - 1mA active current typical - 10 A standby current typical at 5.5V - 5 A standby current typical at 3.0V • Organized as two or four blocks of 256 bytes (2x256x8) and (4x256x8) • Two wire serial interface bus, I2CTM compatible • Schmitt trigger, filtered inputs for noise suppression • Output slope control to eliminate ground bounce • 100KHz(2.
TDA8374A (Single chip TV Processor for Negative modulation IF ) TDA8374 (Single chip TV Processor for Negative & positive modulation IF) (1) General Description The TDA8374(A) is I2C-bus controlled single chip TV processors which are intended to be applied in PAL/NTSC television receiver. The IC is mounted in a S-DIL 56 envelope.
(3) Block Diagram 15
(4) Pin Description No 1 Name SOUND IF INPUT 2 EXT AUDIO INPUT 3 4 VCO REF FILTER 5 PLL LOOP FILTER 6 IF VIDEO OUTPUT 7 8 9 BUS INPUT : SCL BUS INPUT : SDA BANDGAP DECOUPLING 10 CHROMA INPUT 11 12 37 Y/CVBS INPUT MAIN POSITIVE SUPPLY Description The sound equivalent input impedance is 8k5 ohm // 5pF which has to be taken into account for proper termination of the ceramic filters. The DC impedance is very high. The minimum input signal for catching is l mV rms.
No Name 13 17 INT CVBS INPUT EXT CVBS INPUT 14 15 GROUND AUDIO OUTPUT 16 DECOUPLING FILTER TUNING 18 BLACK CURRENT INPUT BLUE OUTPUT GREEN OUTPUT RED OUTPUT 19 20 21 22 V-GUARD INPUT/ BEAM CURRENT LIMITER 23 24 25 26 RED INPUT GREEN INPUT BLUE INPUT RGB INSERTION SWITCH INPUT 27 LUMINANCE INPUT Description A voltage detection circuit is connected to both pins. - pin12 if V12 <6.8V than a power on reset, POR, is generated. The Hout output is disabled immediate. - pin37 if V37 <5.
No Name 28 29 30 LUMINANCE OUTPUT B-Y OUTPUT R-Y OUTPUT 31 32 B-Y INPUT R-Y INPUT 33 SECAM REF OUTPUT X-TAL 3.58 X-TAL 4.43 34 35 36 38 39 40 LOOP FILTER BURST PHASE DETECTOR CVBS OUTPUT BLACK PEAK HOLD CAPACITOR HOR OUTPUT 41 SANDCASTLE OUTPUT/ FLYBACK INPUT 42 PHI-2 FILTER / FLASH PROTECT Description to the luminance input pin 27. The pin is internally AC coupled to the luminance clamp via a capacitor of 50pF; clamping action occurs during burstkey period.
No Name 43 PHI-1 FILTER 44 45 46 47 GROUND EAST-WEST DRIVE VERT DRIVE + VERT DRIVE - 48 49 IF INPUT 50 EHT/OVERVOLTAGE PROTECT INPUT VERT SAWTOOTH CAPACITOR 51 52 53 54 REFERENCE CURRENT INPUT AGC DECOUPLING CAPACITOR TUNER AGC OUTPUT 55 AUDIO DEEMPHASSIS 56 DECOUPLING SOUND DEMODULATOR Description A flash protection becomes active when this pin is forced >6V. The horizontal drive is switched-off immediately.
TDA4665(Base Band Delay Line) (1) Features • Two comb filters, using the switched-capacitor technique,for one line delay time (64µs) • Adjustment free application • No crosstalk between SECAM colour carriers • Handles negative or positive colour-difference input signals • Clamping of AC-coupled input signals(±(R-Y)and±(B-Y)) • VCO without external components • 3MHz internal clock signal derived from a 6MHz VCO, line-locked by the sandcastle pulse (64µs line) • Sample-and -hold circuits and low-pass filters
TDA8395 (Secam Decoder) (1) Features Fully integrated filters Alignment free For use with baseband delay (2) Description The TDA8395 is a self-calibrating,fully integrated SECAM decoder. The IC should preferably be used in conjunction with the PAL/NTSC decoder TDA8362 and with the switch capacitor baseband delay circuit TDA4665. The IC incorporates HF and LF filters, a demodulator and an identification circuit (Iuminance is not processed in this IC).
TDA6106Q ( Video Output Amplifier ) (1) General Description The TDA6106Q is a monolithic video output amplifier (5MHz bandwidth) in a SIL 9 MPpackage, using high-voltage DMOS technology, and is intended to drive the cathode of CRT directly . To obtain maximum performance, the amplifier should be used with black-current control.
I802 PC817 (1) General Description The specification applies to the structures and characteristics of Model No.
TDA8356 (DC-coupled vertical deflection circuit) (1) General Description The TDA8356 is power circuit for use in 90 and 110 color deflection systems for field frequencies of 50 to 120 Hz. The circuit provides a DC driven vertical deflection output circuit, operating as a high efficient class G system.
TDA7056 (BTL AUDIO OUTPUT AMPLIFIER) : 1 SPEAKER MODEL (1) Features • No external components • No switch-on/off clicks • Good overall stability • Low power consumption • Short circuit proof • ESD protected on all pins (2) General Description The TDA7056 is a mono output amplifier contained in a 9 pin medium power package. The device is designed for batteryfed portable mono recorders, radios and television. (3)Block Diagram (4)Pin Description PIN DESCRIPTION 1 n.c.
STR-S5707 (Hybrid IC for a Switching Regulator) (1) General Description The STR-S5707 is a Hybrid IC with a built in power transistor and a separate excitation control IC, designed for converter type switching mode power supply applications. The IC is capable of quasi-resonant mode and requires small number of external component.
Electrical Characteristics of Control Part (Ta=25 ) Description Terminal Symbol Rating Unit MIN TYP MAX On-state Voltage 9-2 VIN(ON) 7.6 8 8.4 V Off-state Voltage 9-2 VIN(OFF) 4.6 4.9 5.2 V Operating Circuit Current 9-2 IIN(ON) 15 28 mA Stand-by Circuit Current 9-2 IIN(OFF) 200 A On Time TON 33 41 Off Time TOFF 45 55 OCP terminal Threshold Voltage 6-2 VOCP -1.12 -1 -0.88 V INH terminal Threshold Voltage 1 8-2 VINH-1 0.65 0.75 0.
TDA8138 (5.1V+12V regulator with Disable and Reset) (1) General Description The TDA8138 is a monolithic dual positive voltage regulator designed to provide fixed precision output voltages of 5.1V and 12V at currents up to 1A. A internal reset cuicuit generates a reset pulse when the output 1 decrease below the regulated voltage value. Output 2 can be disabled by TTL input. Shot circuit and themal protections are included. (2) Feature • output currents up to 1A • ixed precision Output 1 voltage 5.
TDA 1519B(AUDIO OUTPUT AMPLIFIER); 2 SPEAKER MODEL (1) Features • Requires very few external components for Bridge Tied Load(BTL) • Stereo ot BTL application • High output power • Low offset voltage at output (important for BTL) • Fixed gain • Good ripple rejection • Mute/stand-by switch • Load dump protection • AC and DC short-circuit-safe to ground and Vp • Thermally protected • Reverse polarity safe • Capability to handle high energy on outputs(Vp=OV) • No switch-on/switch-off plop • Protected against e
PCA84C 122A(IC REMOCON) (1) Features • ROM, RAM and I/O is device dependent • Two test inputs T0, T1 • 3 Single-level vectored interrupt sources • 8 bit programmable timer/counter with 5-bit pre-scaler • Single supply voltage from 2.0V to 5.5V • On-board oscillator 1MHz to 5MHz • Operating temperature range -20 to +50 C (2) General Description The PCA84C122A is a stand-alone micro controller designed for use in remote control unit for a wide range of applications.
Circuit Description Vision IF amplifier, AFC, video demodulator The IF signal from the tuner is fed through a SAW filter to the differential IF input (pin 48 and 49). The first IF stage consists of 3 AC-coupled amplifiers with a total gain control range of over 66 dB. The reference carrier for the video demodulator is obtained by a PLL carrier regenerator (eliminating notch filter compromises, as in reference tuned circuits for passive carrier regeneration).
This compensates for the storage time of the horizontal deflection transistor. The - 2 loop filter (C) is externally connected to pin 42. The horizontal phase can be given a static off set via I2C-but (HSH “horizontal shift”) A dynamic correction is possible by current feedback into the - 2 loop filter capacitor. To protect the horizontal deflection transistor, the ho rizontal drive is switched off immediately when a power failure ( “ Power-On Reset “ bit POR ) is detected.
Integrated video filters The TDA8374 has alignment-free internal luminance delay, chroma bandpass and chroma trap. They are implemented as gyrator circuits tuned by tracking to the frequency of the chroma Xtal oscillator. The chroma trap in the Y signal path is by-passed when Y/C input is selected (S-VHS ). For SECAM an extra luminance delay is build-in, for correct delay of the luminance signal.
TDA8395 SECAM decoder The TDA8395 is an alignment-free SECAM colour decoder, including a Cloche filter, demodulator and line identification circuit. The Cloche filter is a gyrator-capacitor type. Its frequency is calibrated in the vertical retrace period. The calibration reference( pin 1 ) is obtained from the TDA8374 color X-tal oscillator (pin 33). Pin 7 is a decoupling for the Cloche reference.
TDA8356 vertical deflection. The TDA8356 is a vertical deflection circuit. It can be used in 90 deflection systems with frame frequencies from 50 up to 120 Hz With its bridge configuration the deflection output can be DC coupled with few external components. Only a supply voltage for the scan and a second supply for the flyback are needed. The TDA8356 can drive max.2A. The vertical drive currents of TDA8374 pins 47 and 46 are connected to input pins l and 2 of the TDA8356.
Video amplifiers Three TDA6106Q integrated video amplifiers drive cathode of the picture tube directly. They are protected against CRT flashover discharges and ESD (electro static discharge). The three video amplifiers, have a beam current output I black, used by the TDA8374 black current loop to control the black level on the cathodes. The outputs can be connected together because the black current 1oop sequentially controls the black level for each cathode.
Stand-By Mode While being in remote control stand-by mode, the output voltage is kept on providing to the secondary side and the power transistor operates at A class mode. By connecting INH terminal (Pin 6) to the GND, the OFF-time of the power transistor is fixed at set time ( T OFF = 50usec at Ta = 25 ) of the built-in oscillator, and only ON-time changes depending on input and output conditions of the power supply.
Trouble Shooting Charts 1. NO RASTER CHECK MAIN B+(+123V/+110V) LINE ABNORMAL NORMAL CHECK VOLTAGE AT (+) OF C807(220µF 400V) 310Vdc AT AC 220V CHECK HEATER VOLTAGE, VIDEO B+(200V) LINE, 16.5V & 48V LINE NORMAL ABNORMAL ABNORMAL CHECK / REPLACE F801 FUSE(T4A 250V) CHECK / REPLACE D801~D804(1S1888X4) R803(10W 3.
2.
3. NO VERTICAL SCANING(ONE HORIZONTAL LINE ON SCREEN) CHECK / REPLACE P401 & DY ] CHECK VERTICAL Vcc +16.
4. NO COLOR CHECK VIDEO SIGNAL AT PIN13 OF I501(TDA8374A) [REFER TO WAVEFORM ] ABNORMAL NORMAL CHECK SYSTEM MODE AUTO PAL SECAM N3 N4 N5 CHECK SIGNAL AT PIN29, PIN30 OF I501 ABNORMAL NORMAL CHECK / REPLACE I501 CHECK / REPLACE X501(4.43MHz X-TAL) X502(3.
5. NO SOUND(PICTURE OK) CHECK AUDIO SIGNAL AT PIN15 OF I501 ABNORMAL CHECK MUTE VOLTAGE AT PIN20 OF I701 *MUTE : HIGH ABNORMAL NORMAL CHECK SIF SIGNAL AT PIN1 OF I501 CHECK /REPLACE R619, C602, Q604 D605, Q606, I701 ABNORMAL NORMAL CHECK SIGNAL WAVEFORM AT PIN6 OF I501 [REFER TO WAVEFORM ] CHECK / REPLACE I501 NORMAL NORMAL CHECK AUDIO SIGNAL AT PIN3(TDA7056) [AT PIN 1&9(TDA1519B)] ABNORMAL CHECK / REPLACE D813, C821 CHECK / REPLACE Q501, R602, R603 Q605 & PERI.
6. NO EXTERNAL A/V(RF OK) CHECK EXTERNA AUDIO & VIDEO SIGNAL AT PIN2 & 17 OF I501 RESPECTIVELY ABNORMAL NORMAL OK CHECK RCA JACK CHECK WAVEFORM AT PIN7 & 8 OF I501 ABNORMAL OK CHECK / REPLACE I701 CHECK / REPLACE I501 OK 7. NO ON-SCREEN DISPLAY(PICTURE OK) CHECK HORI. & VER. SYNC AT PIN46 & 45 OF I701 RESPECTIVELY NORMAL ABNORMAL CHECK / REPLACE Q301, Q302(VER. SYNC) D401, R414(HORI. SYNC) OK ABNORMAL NORMAL CHECK WAVEFORM AT PIN23, 24, 25, 26 OF I501 ABNORMAL CHECK / REPLACE PERI.
8. REMOTE CONTROL UNIT TROUBLE(LOCAL CONTROL OK) CHECK PULSE AT COLLECTOR OF Q1(TRANSMITTER BOARD) ABNORMAL CHECK / REPLACE Q1 / LED1 (TRANSMITTER BOARD) CHECK PULSE AT PIN36 OF I701 NG CHECK IC1 (DHR-001S) OK NG CHECK / REPLACE X1, C1 ABNORMAL OK CHECK / REPLACE I704(TFMU5380) NORMAL CHECK / REPLACE I701 & PERI.
IC DC Voltage Charts • Input signal - Video : color BAR(PM5518)-PAL -Audio : 1khz sine wave • User’s control condition - Contrast, Brightness, Color, Volume(Normal condition) • Line Voltage - AC 220V, 50HZ • All the Voltage in each point are measured with multimeter • I701(µ-com) PIN NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 V(DC) 0 4.7 4.5 4.5 4.7 0 0 0 (option) 0 0 4.4 2.0 2.2 0 4.7 PIN NO 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 V(DC) 4.0 0 4.
• I501(TDA8374A) PIN NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 V(DC) 0 3.8 3.6 3.6 2.8 3.0 4.6 4.6 6.64 0 3.4 8.0 100mv G PIN NO 15 16 17 18 19 20 21 22 23 24 25 26 27 28 V(DC) 3.76 3.7 3.5 5.3 2.5 3.8 2.7 3.1 3.4 3.4 3.4 0 2.5 2.5 PIN NO 29 30 31 32 33 34 35 36 37 38 39 40 41 42 V(DC) 1.7 1.7 4.0 4.0 1.6 2.6 2.6 4.6 8.0 3.4 6.0 3.0 0 4.8 PIN NO 43 44 45 46 47 48 49 50 51 52 53 54 55 56 V(DC) 4.0 G 8.0 2.
Electrical Parts List LOC. PART-CODE PART-NAME PART TYPE ZZ100 48B3228B04 TRANSMITTER REMOCON R-28B04 ZZ110 PTACPWA499 ACCESSORY AS DTC-14Q1VM M821 4858211400 POLY BAG P.E FILM T0.03X600X550 30 47P7500001 BATTERY AAM 1.5V 10000 48586A1617 MANUAL INSTRUCTION ALL ZZ120 PTBCSHA499 COVER BACK AS DTC-14Q1VM M211 4852147200 COVER BACK HIPS BK M541 4855415800 SPEC PLATE 150ART P/E FILM (C/TV) M781 4857817611 CLOTH BLACK FELT T0.
LOC. ZZ220 PART-CODE PTSPPWA499 PART-NAME PART TYPE SPEAKER AS DTC-14Q1VM PA601 4850703S03 CONN AS YH025-03+YST025+ULW=200 SP01 4858306810 SPEAKER 3W 16 OHM F2035C03-3 ZZ290 PTMPMSA499 PCB MAIN MANUAL AS DTC-14Q1VM 10 2193102005 SOLDER BAR SN:PB=63:47 S63S-1320 20 2193011101 SOLDER WIRE RS 60-1.2 1.6A 30 2291050615 FLUX SOLDER DF-2012U 40 2291050301 FLUX SOLVENT IM-1000 50 2291140501 WAX COVER C410 CMYH3C692J C MYLAR 1.
LOC. PART-CODE PART-NAME PART TYPE I901 1TDA6106Q- IC AMP TDA6106Q I902 1TDA6106Q- IC AMP TDA6106Q I903 1TDA6106Q- IC AMP TDA6106Q JA01 WP-1BK1715 WIRE LEAD 1007 AWG22 1/0.65 BK 5-170-5 JA02 WP-1BK1715 WIRE LEAD 1007 AWG22 1/0.65 BK 5-170-5 JV03 4859104250 JACK PIN BOARD YSC-0406(YW+YW+RD+RD) L102 58C9780027 COIL CHOKE TRF-1201B (0.
LOC. PART-CODE PART-NAME PART TYPE Z503 5PTPS60MB- FILTER CERA TPS 6.0MB(EFC-S6ROME3) Z504 5PTPS65MB- FILTER CERA TPS 6.5MB(EFC-S6R5ME3) ZZ200 PTMPJ0A499 PCB MAIN (RHU) AS DTC-14Q1VM C308 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16) TP C412 CEXF2C339V C ELECTRO 160V RSS 3.
LOC. PART-CODE PART-NAME PART TYPE C115 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP C116 CMXM2A223J C MYLAR 100V 0.022MF J TP C117 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C119 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C301 CMXB1H104J C MYLAR 50V EU 0.1MF J (TP) C304 CMXB1H104J C MYLAR 50V EU 0.1MF J (TP) C305 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C306 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING) C311 CMXM2A104J C MYLAR 100V 0.
LOC. PART-CODE PART-NAME PART TYPE C702 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP C706 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C707 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) TP C710 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C711 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C712 CEXF1H470V C ELECTRO 50V RSS 47MF (6.3X11) TP C713 CCXF1H103Z C CERA 50V F 0.
LOC.
LOC. PART-CODE PART-NAME PART TYPE C122 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z (AXIAL) C302 CCZB1H181K C CERA 50V B 180PF K (AXIAL) C303 CCZB1H181K C CERA 50V B 180PF K (AXIAL) C401 CBZR1C472M C CERA 16V Y5R 4700PF M (AXIAL) C403 CBZR1C222M C CERA 16V Y5R 2200PF M (AXIAL) C404 CBZR1C222M C CERA 16V Y5R 2200PF M (AXIAL) C405 CCZF1E103Z C CERA 25V F 0.01MF Z (AXIAL) C501 CBZF1H104Z C CERA SEMI 50V F 0.
LOC. PART-CODE PART-NAME PART TYPE DA04 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DA06 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DA09 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DO401 DUZ5R1BM— DIODE ZENER UZ-5.1BM D102 D1N4148—- DIODE 1N4148 (TAPPING) D301 DUZ5R1BM— DIODE ZENER UZ-5.
LOC. D813 PART-CODE DBYV95C—- PART-NAME PART TYPE DIODE BYV95C (TAPPING) D814 DBYV95C—- DIODE BYV95C (TAPPING) L101 5CPZ100K04 COIL PEAKING 10UH 10.5MM K (LAL04TB) L103 5CPZ220K02 COIL PEAKING 22UH K (AXIAL 3.5MM) L401 5CPZ109M02 COIL PEAKING 1UH M (AXIAL 3.5MM) L501 5CPZ150K02 COIL PEAKING 15UH K (AXIAL 3.5MM) L502 5CPZ829K02 COIL PEAKING 8.2UH K (AXIAL 3.5MM) L503 5CPZ100K02 COIL PEAKING 10UH K (AXIAL 3.5MM) L604 5CPZ829K02 COIL PEAKING 8.2UH K (AXIAL 3.
LOC. PART-CODE PART-NAME PART TYPE R310 RD-4Z392J- R CARBON FILM 1/4 3.9K OHM J R311 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R312 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R313 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R314 RD-4Z223J- R CARBON FILM 1/4 22K OHM J R401 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R402 RD-AZ153J- R CARBON FILM 1/6 15K OHM J R403 RD-AZ479J- R CARBON FILM 1/6 4.7 OHM J R404 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R405 RD-AZ152J- R CARBON FILM 1/6 1.
LOC. PART-CODE PART-NAME PART TYPE R530 RD-AZ203J- R CARBON FILM 1/6 20K OHM J R531 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J R532 RD-AZ361J- R CARBON FILM 1/6 360 OHM J R533 RD-AZ472J- R CARBON FILM 1/6 4.
LOC. PART-CODE PART-NAME PART TYPE R703 RD-AZ272J- R CARBON FILM 1/6 2.7K OHM J R705 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R708 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R709 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R710 RD-AZ100J- R CARBON FILM 1/6 10 OHM J R711 RD-AZ333J- R CARBON FILM 1/6 33K OHM J R715 RD-AZ912J- R CARBON FILM 1/6 9.
LOC. PART-CODE PART-NAME PART TYPE R762 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R763 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R764 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R765 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R766 RD-AZ104J- R CARBON FILM 1/6 100K OHM J R767 RD-AZ471J- R CARBON FILM 1/6 470 OHM J R807 RD-4Z330J- R CARBON FILM 1/4 33 OHM J R808 RD-4Z182J- R CARBON FILM 1/4 1.
LOC.
Q / T Difference Part List NO LOC PART NAME Q MODEL(1spk) T MODEL(2spk) 1 I601 IC AMP TDA 7056 TDA 1519B 2 I601A HEAT SINK 4857025400(A1050P-H24 T2) 4857026402(AL EX BK) 3 PA601 CONN AS YH025-03+YST025+ULW=200 YH025-03+YST025+ULW=300 4 PA602 CONN AS - YH025-03+YST025+ULW=600 5 SP01 SPEAKER 6 SP02 SPEAKER - 95BF03LC 7 P602 CONN WAFER - YW025-03(STICK) 8 C613 C CERA 9 J175,J207,J209 WIRE COPPER 3W 16Ω F2035C03-3 7.5W 8Ω 95BF03LC 25V 0.01µF Z(AXIAL) - AWG22 1/0.
CP-370 Inch Difference Part List NO LOC PART NAME 14” MODEL 20” MODEL 1 R407 R-CARBON 1/4W 82K 1/4W 68K 1/4W 68K ABL 2 C410 C-MYLAR 1.6KV 6900PF 1.6KV 7500PF J 1.6KV 6000PF H.V 3 C411 C-MYLAR 200V 0.33MF J 200V 0.36MF J 200V 0.3MF H.V 4 R415 R-FUSIBLE 1W 1.2OHM 1W 2.2OHM 1W 1.