REAR PROJECTION TV INSTRUCTION MANUAL DSJ-4710CRA / 5510CRA DSJ-4720CRA / 5520CRA
PROJECTION TV CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 14.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. In case of an accident, please unplug the unit from the outlet immediately. -4- To reduce the risk of electric shock, do not remove cover or back. No user -serviceable parts inside. Refer to qualified service personnel for repair.
Caution Please keep the user's manual in a safe place for future reference. This section must be read carefully and followed by the user when installing and transporting the product. Do not put volatile substance-such as benzene, naphtha- near the product since it may cause a change in the product's color.
This product has advantages as follows. MAIN POWER CH VOL TIMER STAND BY MENU TV/COMP. TV/VIDEO POWER Large Screen Adoption Dolby Virtual You can enjoy favorite broadcasting by using a large screen with the size of 55”/47” bases on projection technology. You can enjoy vivid and stereo sound as in a theater. Various Screen You can watch various sizes of screen such as 16:9, 4:3, Panorama, Zoom.
Table of Contents Installation and Maintenance Antenna Connection 8 Video Connection 11 Camcorder & Play station Connection 12 DVD Connection 13 Audio Connection 14 Digital Satellite Receiver Connection 15 Cable TV Broadcasting Connection 16 Name of Each Part 18 Basic Guide To setup device change of remote control 22 Method To Use Basic Menu 23 To Watch TV 24 Automatic Channel Memory 26 Selection of Input Signal 32 Application Guide Screen Adjustment 35 Selection of PIP 44 Sou
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. 2. Connect the combining adapter to the antenna input at the back of the TV set. WHEN USING THE COMBINING ADAPTER You may obtain the combining adapter at your closest Service Center.
CTV Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right.
Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection. VHF Antenna UHF Antenna ANT/CABLE 1 Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect S-Video input to enjoy a clearer and brighter picture images. You can choose and make the connection with any one of Video 1,2, or 3 inputs. Connection is not necessary in Mono mode. Connect either S-Video or Video input to the unit. When both are connected, the output display will be in S-Video. Note The stated connection does not comply with recording TV programs.
Camcorder & Play station Connection Watching the Camcorder Recording on TV -Use the input jack provided at the side panel of the TV set -Use the same connection method for playstation Video game Playing a Recorded Material and Recording a Video simultaneously -Connect the camcorder and video as follows. -Turn the camcorder's video output switch on, and play the recorded material. -Press the "TV/VIDEO" button, and select Video 1. -Select A/V INPUT for the Video Input, and start recording.
DVD Connection DVD -480i input signal is possible for DVD input. -DVD screen output is composed of three separate primary color jack(Y/Cb/Cr), resulting in a higher image quality. -Y/Cb/Cr, may also be noted as Y/PB/PR or Y/Pb/Pr in different DVD players. -The DVD player s audio output must be connected to the DVD audio input socket at the back of the TV set. -You must use a 480p input capable DTV jack if you want to get the progressive scan (480p) DVD screen display.
Audio Connection Standard Audio Connection -You may minimize the volume of the TV set, and listen to the sound. -The default status of Dolby Virtual is in Line out: Internal .
Digital Satellite Receiver Connection Watching High Definition Digital Broadcasting The signal input of 1080i, 720p, and 480p are available in this product. You may use a general A/V jack for its connection.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to any of the Video input 1, 2, & 3. Antenna Input Connection Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver.
In simultaneous use of antennas for Cable Broadcasting and General Broadcasting You can alternatively use the antenna input 1 or the antenna input 2 if changing setup in the
Name of Each Part Front Panel Buttons on the TV set have the same function as those of the remote controller. Front Panel Button If you turn the TV set off by pressing the main power button at this panel, it is as unplugging the power cord from the outlet since this will prevent all operation of both the TV set and the remote controller. Unless you are not using the unit for a long period of time, have the main power on this panel turned on at all times.
Side and Rear Panel Side Panel It is convenient to use the input jacks provided at the side panel when connecting to the camcorder or play station. It is also convenient when connecting a personal computer to the TV set, and when listening to the sound through headphones.
Parts of the remote controller This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc. DISPLAY Power TV/VCR/CATV Channel number (0-9) Use to select channel directly 0~9 100 Use it when selecting a channel number of over 100 Prev It returns to previous channel. MENU Use it to make picture adjustment, screen format, sound adjustment, input selection, and utilities. TV/VIDEO Use this function to make video input selection.
VCR Function REW, PLAY, FF, STOP, REC, PAUSE Screen Size This feature converts the screen size by changing its aspect ratio. Each time you press the button, it will be changed from 16:9 4:3 Panorama ZOOM1 ZOOM2 Auto Picture Standard Cinema Caption This feature allows you to choose the caption. Each time the button is pressed it rotates from CC1 CC2 CC3 CC4 Off ANT Dynamic User PIP PIP Search TV/Video STILL SWAP Position When the TV screen image is unclear Do not drop or spill liquid on it.
To setup device change of remote control Method to setup device change of remote control - The remote control is setup to be used for operating the HDTV provided together. You may also setup the remote control in order to operate cable TV receiver or video, etc with a remote control. Notices: Caution • l All the preset codes are erased when replacing the battery. l In this case, you must reset the remote control again.
Method To Use Basic Menu Basic Menu - Basic menu appears on the screen if pressing the menu button of the remote control. - There are 5 items of Picture, Sound, Function, Set up and Special in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. Press the “Menu” button. • The main menu appears if pressing the Menu button. Press the “◀VOL▶” button.
To Watch TV To Watch TV - Buttons with same name in the main body performs same function. Press the “Main Power” button of the main body. •The buttons of the remote control and the main body operate only when pressing the “Main Power” button of the main body. The remote control and the main body do not operate if turning the “Main Power” button of the main body off. When pressing the Channel button •Select two digits if using the number button for channel selection. For example, to watch the No.
Press the “Main Power” button. POWER • Press the “Main Power” button of the main body. • The main power lamp turns on in red color. • Press the “Power” button of the main body or the “Power” button of the remote control. • The main power lamp turns on in “green” color and the TV turns on. Press the “▼CH▲” button. • Select the desired channel by pressing the “▼CH▲” button or the number button. Ex) Channel 09 Air 09 Adjust volume. •Sound reduces if pressing the ◀VOL button.
Automatic Channel Memory Automatic Channel Memory - This is function for the TV to automatically memorize only the broadcasted channel. If setup the Auto Channel, you can simply find out channels with the channel “▼CH▲” button and so need not to select channels by pressing each channel number. - Always enter this function at the regular TV On-Air time with antenna connected. Air/Cable channel currently OnAir is memorized respectively if setup Auto channel for the General/Cable broadcasting.
Select the “Auto Program”. • Select the “Auto Program” with the “▼CH▲” button. Press the “VOL▶” button. • Pressing the “VOL▶” button automatically searches On-Air Channel as in the right. • On Air TV, searches from 2 channels through 69 channels, and on Cable TV, searches from 1 channels through 125 channels. • In this case, if pressing the menu button, the automatic Channel search is stop. However, channels searched by that time are saved. Auto Program is completed.
Additional Channel Memory - This is method for additionally memorize channels not memorized due to weak broadcasting signal. - This function is available even in the
Erase of Memorized Channel - This is function to erase unnecessary Channel memorized. - This function is available even in the
Minute Adjustment of Channel - This is function to clearly adjust the screen to the minute part when any Channel screen appears as a dotted line or when no color appears or when a stripe figure appears or when the screen is unstable. When color looks separated • You must adjust “Color Match” when color of the screen (red, blue, yellow) looks separated or looks spread due to unmatched (See 56 page). Select the Set up with the “Menu” button and the “◀VOL▶” button.
Select Ch Edit • The screen appears as in the right if pressing the “Ch Edit”. Other items for Channel adjustment • This item enables to erase, memorize or minute adjust the channel. • Select the desired Channel firstly. • Performs Add or Erase. • Minute adjust enables to adjust minute and clear thing on the screen. Select Fine • Select Minute Adjust by using the “▼CH▲” button. • Stop to press the “◀VOL▶” button if the screen becomes best conditions.
Selection of Input Signal When watching video, Camcorder, Cable TV - See 11p for connection method of TV and “Video”. - You cannot designate channels when watching video. Press the “TV/VIDEO” button. • Screen changes as follows whenever pressing the “TV/Video Input” button. Notices: Cautions in menu setup • Menu disappears if not operating any button for 10 seconds from the menu. • Don’t connect video signal and S-video signal to the video input terminal (1,2,3) at the same time.
When watching DTV and DVD (component input) - See 13p, 15p for connection method of DTV and DVD (component input). - Input component video (called as color difference signal) as DVD signal. Press the “TV/COMP.” button. • The screen changes whenever pressing the button once.
Method to watch by using Menu button Press the Menu button. • Press the “◀VOL▶” button until the “△” mark will come on the “Special”. • Press the “CH▲” button in the “△” mark will come ont the “Special” Select “Component 1” or “2” from the “Special”. • Component Off is repeated whenever pressing the “VOL▶” button. • Component 1 is repeated whenever pressing the “VOL▶” button. • Component 2 is repeated whenever pressing the “VOL▶” button.
Screen Adjustment When setting up various screen mode - The user may select various screens designed in good appearance in respect of a professional without adjusting the screen individually. Press the “Auto Picture” button. AUTO PICTURE • The screen adjustment status changes as following screens are displayed sequentially whenever pressing the button of the Screen mode. • Screen automatically changes to the User Screen if adjusting Brightness, Contrast, Sharpness, Color, Tint from individual screen mode.
When removing screen noise - Screen noise refers to that screen looks bad as abnormal signal (noise) generates on the screen when broadcasting signals are weak. Press the “Menu” button. • Press the “◀VOL▶” button until the “△” mark will come on the “Picture”. • Press the “CH▲” button if the “△” mark will come on the “Picture”. • Press the “▼CH▲” button and select “Picture NR”. Press the “ VOL▶” button. • If pressing the “Volume ◀▶” button, On and Off of the Picture NR function are repeated.
When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Sharpness, Color, Tint, etc to the user’s taste. Press the “Menu” button and “Picture”. • Press the “◀VOL▶” button until the “△” mark will come on the “Picture”. • Press the “CH▲” button if the “△” mark will come on the “Picture”. Select the item desired to adjust and press the “◀VOL▶” button.
Adjustment of Screen Size - Randomly change the size of the screen. Pleasure for enjoying the TV increases further. - This mode does not operation in the component 1 and 2 terminal. (However, the mode operates when 480i is entered into the component 1 and 2 terminal.) - The 16:9 screen operates when power is turned on firstly. Press the “Screen Size” button. SCREEN SIZE • The screen changes as below whenever pressing the “Screen Size” button.
Method to Setup the Caption Screen Mode - You can watch in character (English) as well as hear sound in watching English caption program. Press the “Caption” button. CAPTION • Setup performed once continues to keep the status as it is. Method to Setup the “Caption” with Menu button Select “Caption” after selecting the “Menu” button and “Function”. • Off - CC1 - CC2 - CC3 - CC4 is repeated whenever pressing the “Volume ◀▶” button.
Setup of Parental Lock - This is function to protect children or juveniles from the harmful broadcasting or videotapes. Press the “Menu” button. • Main menu appears as in the right drawing. Select “Function”. • Select “Function” with the “△” mark by using the “◀VOL▶” button. • Sub-menu appears if pressing the “CH▲” button. Select “Parental Lock” by pressing the “▲CH▼” button. • Press the “VOL▶” button.
Press “Password”. • Press Password by using number 0~9. Caution) If using your password, remember it. It is needed for continuous use of this function hereafter. On – Off of the Parental Control is repeated whenever pressing the “◀VOL▶” button. • A guideline of TV is setup in all the TV programs including sports, news. • The “▼CH▲” button selects items and the “◀VOL▶” button sets up or cancels each item.
• Rating of movie is setup even in movie, videotape and other media objects including TV program. • The “▼CH▲” button selects items and the “◀VOL▶” button sets up or cancels each item. • Interrupts program without rating. • Interrupts program of the input terminal for the outside video (video 1, 2, 3). • Interrupts program of the PIP. • Sets up the Unblock or the Block with the “◀VOL▶” button.
“Change Password”. • In the initial purchase of TV set, password is set to blank. In continuous use of Parental Control, you need to change your password. • If pressing the “◀VOL▶” button after selecting password, the second screen of below drawing appears. Here, newly enter your unique password by using number of 0 through 9. Enter your password in the same manner once again. Exit from the “Parental Control” menu. • The main menu appears if pressing the menu button once.
Selection of PIP When selecting various PIP - You can enjoy various screens to your taste by selecting various functions of PIP. However, you cannot watch same Channel as main screen in the auxiliary screen. - You cannot also watch the input terminal screen of the component 1 and 2 with a PIP (auxiliary screen). Press the “Menu” button and select “Function”. • Select “Function” with the “△” mark by using the “◀VOL▶” button. • Sub-menu appears if pressing the “CH▲” button.
Selection of Auxiliary Screen Channel Press the “PIP” button and press the “▼CH▲” button of the “PIP”. • Select the Channel by pressing the “▼CH▲” button at the right of the “PIP” button. • The memorized Channel of the auxiliary screen can be selected. PIP In case of Main/Auxiliary screen In case of both screens Selection of Auxiliary Screen Position Press the “PIP” button and press the “Position” button. Position of the auxiliary screen changes whenever pressing the position button.
When converting both main screen to auxiliary screen Press the “PIP” button and then press the “SWAP” button. PIP SWAP In case of Main/Auxiliary screen In case of both screens -46- • The main screen changes to auxiliary screen and auxiliary screen changes to main screen.
4-screen Channel Search Function - You can identify broadcasting contents while sequentially searching for only the memorized channel. Press the “Search” button. ▶ The “▶” mark sequentially moves on the search screen whenever pressing the position button on the search screen. ▶ ▶ ▶ If pressing the Main/Auxiliary Conversion button on the search screen, the search screen with the “▶” mark and the main screen converts each other.
Still - This is function to temporarily stop the main screen or the auxiliary screen currently watched. - You can watch favorite scene, etc without missing important information since you can stop the screen. Still of Main Screen STILL • Press the “Still” button when desiring to still the screen currently watched. • Pressing the button once again returns to the screen being watched as the still screen is cancelled.
Sound Adjust When selecting various sound modes Press the “Sound Mode” button. SOUND MODE • Sound status changes while the following screens displays in turn whenever pressing the Sound Mode button.
When adjusting sound to taste - The user can enjoy various sounds by adjusting Sound Mode, Balance, Equalizer What’s equalizer? • High quality sound range adjustment method used for audio products. Sound Balance • Function to adjust balance of sound volume of the left and right speaker. Select “Sound” by pressing the “Menu” button. • The menu screen appears as follows: Select items desired to adjust and press the “◀VOL ▶” button.
In case of adjusting equalizer • Select the Equalizer by pressing the “▼CH ▲” button. • If pressing the “◀VOL▶” button, the Equalizer Adjust mode appears. 0.1 kHz, 0.3 kHz 1.0 kHz, 3.0 kHz 10.0 kHz, 0.3 kHz Low Sound Range Middle Sound Range High Sound Range Select and use the relevant frequency by pressing the “◀VOL ▶” button. • You can adjust degree of the relevant frequency by using the “▼CH▲” button. Adjust sound balance in the same manner, either.
Multi-Sound and Stereo - You can select to your taste since multi-sound broadcasting is broadcast in the order of Mono → Stereo → SAP. - In stereo broadcasting, automatic conversion to the status selected in the multi-sound broadcasting is done. - You may also select this function even in
Adjustment of Current Time - You must previously adjust current time in order to reserve Automatic On/Off. Press the “Menu” button and select “Function”. • Select “Function” by pressing the “◀VOL▶” button and then press the “CH▲” button. Press the “Timer” for selection. • Select “Timer” by pressing the “▼CH▲” button and then press the “◀VOL▶” button. Function Timer PIP Caption Off Language English Parental Lock Move Sel. P r e v. Setup the “Clock”.
Setup of Off-time The red lamp turns on even setting up either of Off-time/ On-time. This function is very convenient since TV is automatically turned off at the fixed time if reserving the Off-time for sleeping time or at desired time. If adjusted once, this function operate everyday unless canceling the Off-time setup or pulling the plugs out. You can reserve current time if setting it up previously. On/Off time setup is erased if pressing and turning the main power off.
Reservation of Sleep Time - This is function to reserve so that TV turns off after a fixed time (10 min. ~ 90 min.) has passed from the current time. - Adjust sleep time with sleep reservation button of a remote control. Press the “SLEEP” button. SLEEP • Sleep Off → Sleep 10 → Sleep 20 → Sleep 30 → Sleep 60 → Sleep 90 → Sleep Off is repeated whenever pressing the “Sleep” button. • Stop to pressing at the desired time. • Sleep Off means status that “Sleep” is not setup.
Adjustment of Color Match Adjustment of Color Match - Perform this adjustment when color looks separated or when focus is not suitable or when the screen looks spread, after movement to another place or watching projection TV for a long time. Press the “Menu” button. • The Menu screen appears as in the right. Select “Special”. • Select “Special” with the “◀ VOL▶” button. • The extension appears if pressing the “CH▲” button.
Select “Convergence”. Adjust the Convergence. • The “▼CH▲” button selects items and the “◀VOL▶” button changes data of the selected item. • The “◀VOL” button moves color to the left (upper) and the “VOL▶” button moves color to the right (lower). • Adjust the screen so that color of the middle cross becomes white. • Adjust blue color in the same manner. • Adjust the screen so that color of the middle cross becomes white in the length and the width. Press the “Menu” button.
Selection of Language Selection of Language This function enables to select language of the OSD displayed on the TV screen. Language of the OSD consists of English, French and Spanish. Press the menu button and select “Function” Select language the “▼CH▲ button” Press the “◀VOL▶ button from Language. Language of the OSD changes in the order of English → Français → Español whenever pressing the volume button.
Troubleshooting Symptoms and Solutions Please check the following list prior to calling Daewoo Electronics Service Center for assistance Is the TV power cord plugged into the outlet correctly? Please check the power cord and connect it properly to the outlet. Press the main power button at the front controller panel. Has the "mute" button at the remote controller been pressed accidentally? Have you checked its volume? Press the "mute" button on the remote controller once more.
Standard of Product DSJ-4710CRA/4720CRA Model DSJ-5510CRA/5520CRA VHF 2~13, 14~69 CATV 1~125 CHANNEL Receipt Channel VHF 2~13, 14~69 CATV 1~125 CHANNEL 119cm NTSC 15W / ch (Main L/R) AC 120V, 60Hz AC 220V, 50/60Hz(Chile, Peru) 230W 1110 x 1210 x 533mm(4710) 1110 x 1210 x 530mm(4720) 62kg Screen Size 139cm Signal Method NTSC Speaker Output Power Power Consumption Dimension (W/H/D) Weight Appearance and standard of this product may change without prior notice for improvement.