LCD TELEVISION INSTRUCTION MANUAL DLP-26C2 DLP-26C3 DLP-32C1 DLP-32C2 DLP-32C3 DLP-37C3 DLP-42C1 GB
Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain them safely for future reference. Follow all operations and instructions accordingly. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
Important Safeguards 13. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 14. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 15.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. WARNING Ignoring or disregarding the contents of this section and improper operation of the product may result in the person’s death or serious injury. In case of an accident, please unplug the unit from the outlet immediately.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. CAUTION Ignoring or disregarding the contents of this section and improper operation of the product may result in the person’s death or serious injury. Please keep the user’s manual in a safe place for future reference.
Table of Contents Installation and Maintenance Antenna Connection . . . . . . . . . . . . Video Connection . . . . . . . . . . . . . . Camcorder & Video Game Connection. DVD Player Connection . . . . . . . . . . STB Connection . . . . . . . . . . . . . . . PC Connection . . . . . . . . . . . . . . . . Cable TV Broadcasting Connection . . . Connect with the Dolby Digital AMP . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplied Accessories Make sure that the following accessories are provided with the product. AC cord AC cord MUTE PICTURE Instruction manual POWER MULTIMEDIA SOUND RECALL ASPECT PR V O L V O L MENU PREV PR OK PR P.MODE DYNAMIC BASS P.STILL P.SWAP P.INPUT 3D-PANORAMA P.PR STILL P.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. 2. Connect the combining adapter to the antenna input at the left side of the TV set. WHEN USING THE COMBINING ADAPTER : You may obtain the combining adapter at your closest Service Center.
Antenna Connection CTV Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right. Antenna socket on the wall Antenna socket at the left side of the TV set ANT/CABLE When a feeder cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right.
Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses. Single Antenna Connection VHF Antenna Back of the tv set UHF Antenna HDMI INPUT PC INPUT AV1 AUDIO AV2 OPTICAL UP-GRADE PCRT Pr Pb R L Y S-VHS AV3 L - AUDIO - R COMPONENT ANT/CABLE Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect an S-Video input to enjoy clearer and brighter picture images. You can make the connection with the AV3 input. HDMI INPUT PC INPUT AV1 AV2 OP AUDIO S-VHS AV3 L - AUDIO - R Note : If S-video and RCA jack are connected the same time, The TV set will only detect the S-Video mode. • If your AV device has both Video OUT terminal and S-Video OUT terminal, the S-Video connection is recommended for better picture quality.
Camcorder & Video Game Connection Watching the Camcorder Recording on TV 1. Prepare the S-video and RCA connector. 2. These connectors connect to S-video or AV 3 as shown in the picture below. 3. Turn on the TV set and camcorder/video game. 4. Select AV3/S-video mode, using the ” ”button of the Remote controller or “ ” button of the TV set. Back of the tv set Camcorder Video game Note : If S-video and RCA jack are connected at the same time, the TV set only detects the S-Video mode.
DVD Player connection When connecting with a component cable and Euro SCART cable Back of the tv set DVD Note : • When you connect with the component video, please check the colour of the cable between the DVD and TV set. When connecting with a S-VHS cable and RCA cable Back of the tv set DVD Note : If S-video and RCA jack are connected at the same time, the TV set will only detect the S-Video mode.
STB(Set Top Box) Connection When connecting with a HDMI cable Back of the tv set Set Top Box When connecting with a component cable Back of the tv set Set Top Box 15
PC Connection When connecting with PC(D-Sub) cable. 1. First adjust resolution of the PC. (640 X 480, 800 X 600, 1024 X 768) 2. Connect between PC and TV set using the D-sub and Audio cable as shown in the picture below. 3. Turn on the PC and TV set. 4. Select PC mode by pressing “MULTIMEDIA” button on the remote control or ” ” button of the TV set. Back of the tv set PC When connecting with a HDMI cable. 1. First adjust resolution of the PC. (640 X 480, 800 X 600, 1024 X 768) 2.
PC Connection PC CONNECTION NOTES: 1) The resolution of the TV set is best at 1024 768(XGA). 2) If there is a [Vertial Frequency] setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz. 3) If the PC resolution is too high, it may be hard to detect signals. Select a suitable resolution. 4) HDMI input port receives only digital Signal. 5) Depending on the graphic card when you plug & unplug the HDMI connection the screen may not display correctly. Restart the computer if this happens.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to any of the Component input and SCART input AV1, AV2. Input Cable TV Broadcasting Station CATV Receiver Antenna Input Connection Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver.
Connect with the Dolby Digital AMP. If you connect the optical output to a Dolby digital AMP, you can listen to better sound.
Name of Each Part Front Panel (DLP-26C2 / DLP-32C2) Buttons on the TV set have the same functions as those of the remote controller. Control Key Buttons. ① Buttons : Each time you press this button, the TV will cycle through: TV / AV1 / AV2 / AV3(S-Video) / PC/HDMI / COMPONENT. ② MENU Button : Use this button to enter and exit the MENU. ③ Buttons : Use this buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Front Panel (DLP-26C3 / DLP-32C3 / DLP-37C3) Buttons on the TV set have the same functions as those of the remote controller. Control Key Buttons. ① Button : Each time you press this button, the TV will cycle through: TV / AV1 / AV2 / AV3(S-Video) / PC/HDMI / COMPONENT. ② MENU Button : Use this button to enter and exit the MENU. ③ Buttons : Use this buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Front Panel (DLP32C1 / DLP-42C1) Buttons on the TV set have the same functions as those of the remote controller. Control Key Buttons. ① AV Button : Each time you press this button, the TV will cycle through: TV / AV1 / AV2 / AV3(S-Video) / PC/HDMI / COMPONENT. ② MENU Button : Use this button to enter and exit the MENU. ③ Buttons : Use this buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Side and Rear Panel Side Panel Rear Panel 23
Parts of the Remote Controller This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc. MUTE PICTURE 1. (MUTE) : Press this button, and the sound goes off. Press again, and the sound returns. 2. (POWER) : TV on/off button in Stand-By mode. POWER 3. PICTURE MODE : Picture modes changes as follows: Normal => Movie => Favourite => Normal MULTIMEDIA SOUND RECALL ASPECT PR V O L 5.
Parts of the remote controller 18. DYNAMIC BASS : Using this button, you can enhance the bass. MUTE PICTURE POWER MULTIMEDIA SOUND RECALL ASPECT PR V O L 20. : When sub screen is RF(TV) mode in the POP, you can change PROGRAMMES using this button. 21. : You can select sound mode in Mono, Stereo, Dual1, Dual2, NiCAM STEREO. It works only in TV mode. 22. STILL : Press this button to freeze the picture. V O L MENU 19.
Method To Use Basic Menu Basic Menu - The basic menu appears on the screen if you press the “MENU” button of the remote control. - There are 5 items Picture, Screen, Sound, Function, and Install in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1. Press the “MENU” button. • The main menu appears if you press the “MENU” button.
To Watch TV On/Off, Number, Mute, Recall, , Buttons with same name in the main body performs the same function. Press the “ON/OFF” button of the front side of the set or Remote controller. • The buttons of the remote control and the main body operate only when AC power is turned on. Note : You can also turn on the TV using “ ” or digit key in the ST-BY mode.
To Watch TV 1. Press the “ON/OFF” button of the main body. • The Stand By LED lamp turns on in red colour. • Press “ ” button of the main body or “POWER” button of the remote control. • The Stand By LED lamp on the front panel begins to fliker in red and green colour and the TV turns on. 2. Press the “ ” button. • Select the desired program by pressing the “ number button. 3. Adjust volume.
Setting Up TV Stations Auto Tuning - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1. Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “ Mode ” buttons. Picture Screen Sound Normal Brightness 32 Contrast 58 Colour 32 Sharpness 32 Tint 32 Colour Temp Normal Function Install Position 2. Select the “Auto Tuning”.
Setting Up TV Stations Manual tuning 1. Press the Number buttons(0~9) or the “ a program number you want. ” button to select 2. Locate the selection bar on the Manual tuning at the Install menu. • Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “ ” buttons. • Place the selection bar on Manual Tuning and press the “ ” button. Auto Tuning Manual Tuning Picture Setup Screen Edit Sound Function Install Position 3. Press the “ ” buttons.
Setting Up TV Stations Setup The Setup menu shows you information as follows: - Picture information: PAL, SECAM, and SECAM-L - Sound information: L, DK3, DK2, DK1, I, BG - Station name, Program number and Real channel number. 1. Searching for channels in the Setup menu • Press the “ “ buttons to select a program number you want. • Move to SETUP in the Install menu. • Select the colour and sound system which you want. • Search a real channel with “ “ buttons.
Setting Up TV Stations Edit The Edit menu shows you information as follows: - Program position assignment: Program number and Station name, Real channel number. - Skip information: Red (Skip Yes), White (Skip No). 1. Deleting the program positions. • Move to EDIT in the Install menu. • Move the selection bar to program number to delete with the “ ” or “ “ buttons. • Press the Delete(Yellow) button. Edit Pr 01 02 03 04 05 06 07 08 09 10 Ch.
Selection of AV and Multimedia Input Signal When watching video, Camcorder, DVD, Cable TV with AV - See page 12 for connection method of Camcorder and Video. - When pressing ” ” button on the TV set, screen changes as follows: TV => AV1 => AV2 => AV3/S-Video => PC => HDMI => Component => TV 1. Pressing the “ ” button on the remote controller.
Selection of AV and Multimedia Input Signal When connecting PC, STB, DVD with Multimedia 1. Pressing the “MULTIMEDIA” button on the remote controller. • The screen changes as follows: PC => HDMI => Component => PC MUTE PICTURE SOUND MULTIMEDIA RECALL ASPECT PC Clock POWER PR 12 : 00 Component HDMI Clock Clock 12 : 00 12 : 00 HDMI & PC mode 1. For optimum picture quality, use 1024x768 computer or set top box output at a 60Hz refresh rate.
Screen Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or colour individually. 1. Pressing the “PICTURE” button. • The screen changes as follows: Normal => Movie => Favourite => Normal • The screen adjustment status changes as the following screens are displayed sequentially whenever pressing the “PICTURE” button. • The screen returns to the mode prior to turning power off when you power on again.
Screen Adjustment When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Colour, Sharpness, etc to the user’s taste. 1. Select “PICTURE” by pressing the “MENU” button. • The menu screen appears as follows. Mode Picture Screen Sound Normal Brightness 32 Contrast 58 Colour 32 Sharpness 32 Tint 32 Colour Temp Normal Function Install Position 2. Select and adjust each items. • Move to the PICTURE menu.
Screen Adjustment Adjustment of Screen Size in TV and AV mode - Randomly change the size of the screen. - The AUTO screen operates when power is first turned on. MUTE 1. Pressing the “ASPECT” button on the remote controller.
Screen Adjustment Adjustment of the screen in the PC mode 1. Adjustment of the H-Position • Move to H-Position in the Screen menu. • Press the ” ” buttons to adjust the horizontal position of displayed image. Aspect Picture Screen 16 : 9 H-Position -3 V-Position 0 Phase 2 Auto Sound Function Install Position 2. Adjustment of the V-Position • Move to V-Position in the Screen menu. ” buttons to adjust the vertical position of dis• Press the ” played image.
POP Mode 1. POP mode when main picture is TV and AV. • Press the “P.MODE” button, then POP mode will function. • Press the “P.STILL” button, then Sub screen will freeze. • If you want to swap main for the Sub, press the “P.SWAP” button. • If you want to change the sub screen input, press the “P.INPUT” button. Sub screen changes as follows: PC => HDMI => Component => PC PREV PR OK PR P.MODE 2. POP mode when main picture is Multimedia. • Press the “P.MODE” button, then POP mode will function.
Sound Adjustment When selecting various sound modes 1. Sound mode selects what you want. • Press the “SOUND” button, then the sound status changes as followed : Favourite => News => Music => Favourite MUTE PICTURE POWER SOUND MULTIMEDIA RECALL ASPECT PR V O L Mode News Mode Music Note : • News : Allows human voice to be heard more clearly • Music : Suitable for listening to music • Favourite : Allows the user to adjust as desired.
Sound Adjustment When adjusting sound to taste - The user can enjoy various sounds by adjusting Sound Mode, Equalizer, 3D Panorama, Dynamic Bass and Balance. 1. To adjust the audio equalizer • Move to Equalizers in the Sound menu. • Select and use the relevant frequency by pressing ” button. the ” • You can adjust the degree of the frequency by using the ” ” button.
Sound Adjustment Multi-Sound and Stereo 1. Mono Sound Selection • During Stereo sound reception if the stereo is weak, you can switch to MONO by pressing the “MTS” button. Then the colour of “MONO” character will change to Red. In Mono reception the depth of sound is improved. • To switch back to stereo, press the “MTS” button again. P.MODE DYNAMIC BASS P.STILL P.SWAP P.PR STILL P.PR 1 2 3 4 5 6 7 8 9 LOCK Mode P.
Selection of Language Selection of Language When you first turn on the TV set, the window of language selection is displayed automatically. 1. Press the “MENU” button and select “Function”. Language Picture Timer Childlock Screen Off MGDI DEMO Sound Function Install Position 2. Select “Language” by pressing “ Access Exit Language ” button. Picture Timer Childlock Screen Off MGDI DEMO Sound Function Install Position 3. Select your desired language by pressing the “ ” button.
Adjustment of Time Adjustment of Time - You must previously adjust current time in order to reserve Automatic On/Off. 1. Setting the Clock • Move to Timer in the Function menu. ” button. • To go to the Clock, press the “ • Place the cursor to Hour / Minute with “ ” buttons. • Set the Hour / Minute with the “ ” buttons. ” buttons and then press • Place the cursor to Clock with “ the “MENU” button to complete.
Adjustment of Time 4. Set up of Off Time • Move to Timer in the Function menu. • To go to the Off Timer, press the “ ” button. • Select Off Timer to “Yes” • Set the Off time in the same way as above for the Clock. The set will turn off at the selected time.
Other Functions 1. Setup of Child Lock • Move to Child Lock in the Function menu. ” button • Select Child Lock to “On” using the “ • You can also select this function using the “LOCK” button on the remote controller. Language Picture Timer Childlock Screen On MGDI DEMO Sound Note : • This prevents the use of the TV set without the remote control. • If TV set is set up Child Lock, LED will cycle through red/green for the ST-BY mode.
Teletext Teletext SWITCHING TELETEXT ON/OFF Press the “TELETEXT” button ( ). The index page or the page viewed last will appear. Press the “TELETEXT” button again to return to the TV mode. NOTE: Teletext works only in TV/AV mode. COLOUR BUTTONS IN TOP/FLOF TELETEXT A red, green, yellow and blue field is shown at the bottom of the screen.
Assemble / separate parts How to arrange the connecting lines and assemble/separate parts 1. COVER WIRE assembly, decomposition method. • When separate : After pressing both sides to the direction of arrow, pull backward.
Assemble / separate parts 2. How to arrange the connecting lines. • After connecting the lines to the TV SET, you can pass the lines through the room of COVER WIRE, and then connect the lines to the other instruments How to separate the STAND AS’ from the TV SET and how to assemble/separate the COVER BOTTOM to/from the TV SET when using the wall mount 1. How to separate the STAND AS’ from the TV SET. • Separate the COVER WIRE from the COVER BACK. • Unscrew the 4 screw from the COVER BACK holes.
Assemble / separate parts 2. How to assemble the COVER BOTTOM to the TV SET. ❶ Inset the backside hook of the COVER BOTTOM to the room of the COVER BACK. ❷ And then rotate the COVER BOTTOM until front snap-fit of the COVER BOTTOM is locked. ❶ ❷ ❷ 3. How to separate the COVER BOTTOM from the TV SET. ❶ Push the two protrusions of COVER BOTTOM with one finger of each hand and then ❷ pull downside the COVER BOTTOM.
Troubleshooting Symptoms and Solutions Please check the following list prior to calling Daewoo Electronics Service Centre for assistance. Symptom Check items Neither picture nor sound - Check the contact of sockets is all right. - Check the TV main power is on. Picture is OK but no sound - Check the Volume control is set to minimum or mute. Sound is OK, but no colour. - Check the colour control and adjust it properly. - Check the program is in colour and not in black & white. The picture has image.
Troubleshooting In PC mode Symptom Check items “OUT OF RANGE” appears on the screen - Check the resolution and frequency of your PC. Then, adjust them to optimum condition for LCD TV. - Refer to the table of PC mode input format (If registered resolution and frequency on the table no listed then no picture will be displayed.) “NO SIGNAL” appears on the screen. - Ensure that the signal cable is firmly connected to PC and TV. Image is not clear. - Adjust the PHASE control. Image is not centered.
Standard of Product Model LCD Panel DLP-26C2 DLP-32C2 Screen Size 26” 32” Aspect Ratio 16:9 16:9 Resolution 1366 x 768 (WXGA) 1366 x 768 (WXGA) Pixel Pitch 0.4215 mm 0.51075 mm Contrast Ratio 3000:1 3000:1 Dimension (W x H x D) Set Dimension 812 X 502.7 X 240mm 944 X 585.5 X 240mm Power Consumption Max.