GB LCD TELEVISION INSTRUCTION MANUAL DLP-26C2Fxx DLP-26C3Fxx DLP-32C1Fxx DLP-32C2Fxx DLP-32C3Fxx DLP-32C5Fxx DLP-32C6Fxx DLP-32C7Fxx DLP-37C3Fxx DLP-37C7Fxx
Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute the risk of an electric shock.
Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain them safely for future reference. Follow all operations and instructions accordingly. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
Important Safeguards 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken from touching such power lines or circuits as contact with them might be fatal. 13. Overloading Do not overload wall outlets and extension leads as this can result in a risk of fire or electric shock. 14.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. WARNING Ignoring or disregarding the contents of this section and improper operation of the product may result in the person’s death or serious injury. In case of an accident, please unplug the unit from the outlet immediately.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. CAUTION Ignoring or disregarding the contents of this section and improper operation of the product may result in the person’s death or serious injury. Please keep the user’s manual in a safe place for future reference. Do not view the TV too closely since it may cause damage to your eyes.
Table of Contents Installation and Maintenance Antenna Connection . . . . . . . . . . . . Video Connection . . . . . . . . . . . . . . Camcorder & Video Game Connection . DVD Player Connection . . . . . . . . . . STB Connection . . . . . . . . . . . . . . . PC Connection . . . . . . . . . . . . . . . . Cable TV Broadcasting Connection . . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplied Accessories Make sure that the following accessories are provided with the product. AC lead Instruction manual Cover Bottom - When you install on a wall mounting you can fit cover bottom as shown in upper picture. Remote control Batteries Cable holder (Except C2 Series) A The method of wire arrangement 1. Assemble the cable holder enclosed on the back of TV.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. combining adapter 2. Connect the combining adapter to the antenna input at the left side of the TV set. WHEN USING THE COMBINING ADAPTER : You may obtain the combining adapter at your closest Service Centre.
Antenna Connection CTV Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right. Antenna socket on the wall Antenna socket at the left side of the TV set ANT/CABLE When a feeder cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right.
Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses. Single Antenna Connection VHF Antenna Back of the tv set UHF Antenna HDMI INPUT AV1 AV2 PC INPUT PC AUDIO Pr Pb R L Y S-VIDEO AV3 L - AUDIO - R COMPONENT ANT/CABLE Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect an S-Video input to enjoy clearer and brighter picture images. You can make the connection with the AV3 input. S-Video HDMI INPUT PC INPUT AV1 AV2 PC AUDIO S-VIDEO AV3 L - AUDIO - R Note : If S-video and RCA jack are connected the same time, The TV set will only detect the S-Video mode. • If your AV device has both Video OUT terminal and S-Video OUT terminal, the S-Video connection is recommended for better picture quality.
Camcorder & Video Game Connection Watching the Camcorder Recording on TV 1. Prepare the S-video and RCA connector. 2. These connectors connect to S-video or AV 3 as shown in the picture below. 3. Turn on the TV set and camcorder/video game. 4. Select AV3/S-video mode, using the ”AV”button of the Remote controller or “ HDMI INPUT PC INPUT AV1 ” button of the TV set.
DVD Player connection When connecting with a component cable and Euro SCART cable HDMI INPUT PC INPUT AV1 AV2 PC AUDIO Pr Pb R L Y S-VIDEO AV3 L - AUDIO - R COMPONENT Back of the tv set Note : • When you connect with the component video, please check the colour of the cable between the DVD and TV set.
STB(Set Top Box) Connection When connecting with a HDMI cable HDMI INPUT PC INPUT AV1 AV2 PC AUDIO Pr Pb R L Y S-VIDEO AV3 L - AUDIO - R COMPONENT Back of the tv set Set Top Box When connecting with a component cable HDMI INPUT PC INPUT AV1 AV2 PC AUDIO Pr Pb R L S-VIDEO AV3 L - AUDIO - R COMPONENT Back of the tv set Set Top Box 15 Y
PC Connection When connecting with PC(D-Sub) cable. 1. First adjust resolution of the PC. (Refer to table in page 17.) 2. Connect between PC and TV set using the D-sub and Audio cable as shown in the picture below. 3. Turn on the PC and TV set. 4. Select PC mode by pressing the “MULTIMEDIA” button on the remote control or ” ” button of the TV set. Back of the tv set HDMI INPUT PC INPUT AV1 AV2 PC AUDIO Pr Pb R L Y S-VIDEO AV3 L - AUDIO - R COMPONENT PC When connecting with a HDMI cable. 1.
PC Connection PC CONNECTION NOTES: 1) The resolution of the TV set is best at 1360 x 768(WXGA). 2) If there is a [Vertial Frequency] setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz. 3) If the PC resolution is too high, it may be hard to detect signals. Select a suitable resolution. 4) HDMI input port receives only digital Signal. 5) Depending on the graphic card when you plug & unplug the HDMI connection the screen may not display correctly. Restart the computer if this happens.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to either the Component input or SCART input AV1 or AV2.
Name of Each Part Front / Side Panel Buttons on the TV set have the same functions as those of the remote controller. Control Key Buttons. ① TV/VIDEO Button : Each time you press this button, the TV will cycle through: TV / AV1 / AV2 / AV3(S-Video) / PC/HDMI / COMPONENT. ② MENU Button : Use this button to enter and exit the MENU. ③ ▲ VOL ▼Buttons : Use these buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Side and Rear Panel Side Panel HDMI INPUT PC INPUT AV1 AV2 PC AUDIO Pr Pb R L S-VIDEO AV3 L - AUDIO - R COMPONENT Rear Panel 20 Y
Parts of the Remote Controller This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc. 1. (MUTE) : Press this button, and the sound goes off. Press again, and the sound returns. 2. (POWER) : TV on/off button in Stand-By mode. 3. MULTIMEDIA :Each time you press this button,the TV will cycle through: PC HDMI Component PC 4.AV/TV : Each time you press this button, the TV will cycle through: TV AV1 AV2 AV3/S-Video TV 5. SLEEP : Sleep Timer setting.
Parts of the remote controller 18. PREV PR : Previous PROGRAMME button in TV mode. 19. MENU : Menu display button. 20. ASPECT : Select screen aspect ratio. Auto 16:9 14:9 4:3 Zoom1 Zoom2 Auto Note : When current mode is multimedia ( PC, HDMI, Component), the aspect only works as the 16:9 mode. 21. NORMAL : changes picture mode as follows: Normal I Normal II Favourite Normal I 22. RECALL : The present modes(TV, V ideo, Component, PC) and Signal information.
Method To Use Basic Menu Basic Menu - The basic menu appears on the screen if you press the “MENU” button of the remote control. - There are 5 items Picture, Screen, Sound, Function, and Install in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1. Press the “MENU” button. • The main menu appears if you press the “MENU” button. MENU PICTURE M PICTURE MODE BRIGHTNESS CONTRAST COLOUR SHARPNESS TINT COLOUR TEMP POSITION 2.
To Watch TV On/Off, Number, Mute, Recall, VOL , PR Buttons with same name in the main body performs the same function. Press the “ON/OFF” button of the front side of the set or Remote controller. • The buttons of the remote control and the main body operate only when AC power is turned on. Note : You can also turn on the TV using “ PR ” or digit key in the ST-BY mode. When pressing the Program button • Select two digits if using the number button for channel selection. For example, to watch channel No.
To Watch TV - If AV1 terminal on TV set is connected with external device, TV will be ON at AV1 mode. Otherwise, TV will be ON at RF mode. - The very first time that you turn on the TV, the LANGUAGE menu will appear on the screen. Its purpose is to enable you to select the language that will be used for all the OSD (On Screen Display) menus. The user must enter a choice of language before proceeding further.
Setting Up TV Stations Auto Tuning - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1. Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “ / ” buttons. PICTURE PICTURE MODE BRIGHTNESS CONTRAST COLOUR SHARPNESS TINT COLOUR TEMP POSITION NORMAL 50 74 50 50 50 NORMAL ACCESS 2. Select the “Auto Tuning”.
Setting Up TV Stations Manual tuning 1. Press the Number buttons(0~9) or the “ PR ” button to select a program number you want. 2. Locate the selection bar on the Manual tuning at the Install menu. • Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “ / ” buttons. • Place the selection bar on Manual Tuning and press the “ ” button. INSTALL AUTO TUNING MANUAL TUNING SETUP EDIT POSITION 3. Execute Manual Tuning.
Setting Up TV Stations Setup The Setup menu shows you information as follows: - Picture information: PAL, SECAM, and SECAM-L - Sound information: L, DK3, DK2, DK1, I, BG - Station name, Program number and Real channel number. 1. Searching for channels in the Setup menu • Press the “ PR “ buttons to select a program number you want. • Move to SETUP in the Install menu. • Select the colour and sound system which you want. • Search a real channel with “ / “ buttons.
Setting Up TV Stations Edit The Edit menu shows you information as follows: - Program position assignment: Program number and Station name, Real channel number. - Skip information: Red (Skip Yes), White (Skip No). - One can move on this edit mode directly using „EDIT” button on the remote control. 1. Deleting the program positions. • Move to EDIT in the Install menu. • Move the selection bar to the program number to delete with the “ / ” or “ / “ buttons. • Press the Delete(Yellow) button.
Selection of AV and Multimedia Input Signal When watching video, Camcorder, DVD, Cable TV with AV - See page 12 for connection method of Camcorder and Video. - When pressing ” ” button on the TV set, screen changes as follows: TV AV1 AV2 AV3/S-Video PC HDMI Component TV 1. Pressing the “AV” button on the remote controller.
Selection of AV and Multimedia Input Signal PC Clock 12 : 00 COMPONENT HDMI Clock Clock 12 : 00 12 : 00 HDMI & PC mode 1. For optimum picture quality, use 1360x768 computer or set top box output at a 60Hz refresh rate. Using other formats or refresh rates may result in reduced picture quality. 2. If the message ‘No signal’ appears on the screen, adjust the PC output to a format listed in the Multimedia Input table.
Screen Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or colour individually. 1. Pressing the “NORMAL” button. • The screen changes as follows: Normal I Normal II Favourite Normal I • The screen adjustment status changes as the following screens are displayed sequentially whenever pressing the “NORMAL” button. • The screen returns to the mode prior to turning power off when you power on again.
Screen Adjustment When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Colour, Sharpness, etc to the user’s taste. 1. Select “PICTURE” by pressing the “MENU” button. • The menu screen appears as follows. PICTURE PICTURE MODE BRIGHTNESS CONTRAST COLOUR SHARPNESS TINT COLOUR TEMP POSITION NORMAL 50 74 50 50 50 NORMAL ACCESS EXIT PICTURE 2. Select and adjust each item. • Move to the PICTURE menu.
Screen Adjustment Adjustment of Screen Size in TV and AV mode - Randomly change the size of the screen. - The AUTO screen operates when power is first turned on. 1. Pressing the “ASPECT” button on the remote controller. • The screen changes as follows: Auto 16:9 14:9 4:3 Zoom 1 Zoom 2 Auto SCALE AUTO SCALE ZOOM2 SCALE SCALE ZOOM1 SCALE 14 : 9 SCALE 4:3 • Auto : This mode will display depending on the signal information of a broadcasting station.
Screen Adjustment Adjustment of the screen in the PC mode 1. Adjustment of the H-Position • Move to H-Position in the Screen menu. • Press the ” / ” buttons to adjust the horizontal position of displayed image. SCREEN SCALE H-POSITION V-POSITION PHASE CLOCK AUTO-ADJUST 2. Adjustment of the V-Position • Move to V-Position in the Screen menu. • Press the ” / ” buttons to adjust the vertical position of displayed image.
Sound Adjustment When selecting various sound modes 1. Sound mode selects what you want. • Press the “SOUND” button, then the sound status changes as followed : Normal Speach Music Favourite Normal SOUND MODE SOUND MODE NORMAL SOUND MODE FAVOURITE SOUND MODE Note : • Normal : normally recommended sound. • Favourite : Allows the user to adjust as desired. • Speach : Allows human voice to be heard more clearly. • Music : Suitable for listening to music.
Sound Adjustment When adjusting sound to taste - The user can enjoy various sounds by adjusting Sound Mode, Equalizer and Balance. 1. To adjust the audio equalizer • Move to Equalizer in the Sound menu. • Select and use the relevant frequency by pressing the ” / ” button. • You can adjust the degree of the frequency by using the ” / ” button. SOUND SOUND MODE EQUALIZER BALANCE Note : • Whenever you adjust the audio equalizer, it stores in the Favourite mode.
Sound Adjustment Multi-Sound and Stereo 1. Mono Sound Selection • During Stereo sound reception if the stereo is weak, you can switch to MONO ” button. Then the colour of “MONO ” character will by pressing the “ change to Red. In Mono reception the depth of sound is improved. • To switch back to stereo, press the “ ” button again. MTS Note : •“ MONO MTS MONO MTS DUAL 2 ” only works in RF mode. 2.
Selection of Language Selection of Language When you first turn on the TV set, the window of language selection is displayed automatically. 1. Press the “MENU” button and select “Function”. FUNCTION LANGUAGE TIMER CHILD LOCK MGDI DEMO OSD HALFTONE POSITION 2. Select “Language” by pressing “ / ” button. OFF 0 ACCESS EXIT FUNCTION LANGUAGE TIMER CHILD LOCK MGDI DEMO OSD HALFTONE POSITION 3. Select your desired language by pressing the “ / ” button. Then, it will set automatically.
Adjustment of Time Adjustment of Time - You must previously adjust current time in order to reserve Automatic On/Off. 1. Manual clock setting • Move to Timer in the Function menu. • To go to the Clock, press the “ ” button. • Place the cursor to Hour / Minute with “ / ” buttons. • Set the Hour / Minute with the “ / ” buttons. • Place the cursor to Clock with “ / ” buttons and then press the “MENU” button to complete.
Adjustment of Time 4. Set up of Off Time • Move to Timer in the Function menu. • To go to the Off Timer, press the “ / ” button. • Select Off Timer to “Yes” • Set the Off time in the same way as above for the Clock. The set will turn off at the selected time. FUNCTION CLOCK AUTO CLOCK AUTO CLOCK PR WAKE UP WAKE UP TIME WAKE UP PR OFF TIMER OFF TIME Note : • This function is very convenient since the TV automatically turns off at the fixed time POSITION 5.
Other Functions 1. Setup of Child Lock • Move to Child Lock in the Function menu. • Select Child Lock to “On” using the “ ” button • You can also select this function using the “LOCK” button on the remote controller. Note : • This prevents the use of the TV set without the remote control. • If TV set is set up Child Lock, LED will cycle through red/ off for the ST-BY mode. • If the Child Lock is “On”,then the set can only be switched back on using the remote control.
Teletext Teletext SWITCHING TELETEXT ON/OFF Press the “TEXT” button ( ). The index page or the page viewed last will appear. Press the “TEXT” button again to return to the TV mode. NOTE: Teletext works only in TV/AV mode. COLOUR BUTTONS IN TOP/FLOF TELETEXT A red, green, yellow and blue field is shown at the bottom of the screen. If TOP or FLOF Teletext is transmitted by the station, pressing the corresponding colour button R,G,Y,B on the remote controller, enables you to select the desired page easily.
Troubleshooting Symptoms and Solutions Please check the following list prior to calling Daewoo Electronics Service Centre for assistance. Symptom Check items Neither picture nor sound - Check the contact of sockets is all right. - Check the TV main power is on. Picture is OK but no sound - Check the Volume control is not set to minimum or mute. Sound is OK, but no colour. - Check the colour control and adjust it properly. - Check the program is in colour and not in black & white.
Troubleshooting In PC mode Symptom Check items “UNSUPPORTED” appears on the screen - Check the resolution and frequency of your PC. Then, adjust them to optimum condition for LCD TV. - Refer to the table of PC mode input format (If registered resolution and frequency on the table not listed then no picture will be displayed.) “NO SIGNAL” appears on the screen. - Ensure that the signal cable is firmly connected to PC and TV. Image is not clear. - Adjust the PHASE control. Image is not centered.
Standard of Product Screen Size 26”(66Cm) 32”(81Cm) 1366 x 768 (WXGA) Resolution Pixel Pitch Contrast Ratio Dimension (W x H x D) Power Consumption TV System 37”(94Cm) 16:9 Aspect Ratio 0.4215 mm 0.51075 mm 0.600 mm 4000:1 5000:1 5000:1 676 x 530 x 230 mm 806 x 626.5 x 250 mm 940 x 720 x 328.5 mm Remarked in the back of product PAL B/G, D/K, I/I, SECAM B/G, D/K, L/L’, NTSC(AV) 220 -240V~, 50/60Hz Power Source ※ Owing to our policy of continuous improvement, specifications may change.
DMP3994500
