DMB-3003LH 2003.3.
DMB-3003LH 2003.3.4 9:56 AM 페이지1 SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE INSTALLING AND OPERATING THE UNIT: This air conditioner meets strict safety and operating standards. The installer of this unit must install or service this unit so it operates safely and efficiently. Precautions When Wiring: • Do not plug in the unit until all connections (tubing, drain hose, mounting, etc.) have been made and double-checked.
DMB-3003LH 2003.3.4 9:56 AM 페이지2 ROOM AIR CONDITIONER INSTRUCTION Remark per EMC Directive 89/336/EEC To prevent flicker impressions during the start of the compressor (technical process) following installation conditions do apply. 1. The power connection for the air conditioner has to be done at the main power distribution. This distribution has to be of an low impedance. Normally the required impedance is reached at a 32A fusing point. Air conditioner fuse has to be 16A max! 2.
DMB-3003LH 2003.3.4 9:57 AM 페이지3 CONTENTS It is recommended that you read the Installation and Operating instructions fully before installing and/or operating this unit. Safety Instructions............................................................................................................................................... 1 Contents................................................................................................................................................................
DMB-3003LH 2003.3.
DMB-3003LH 2003.3.4 9:57 AM 페이지5 LOCATION OF CONTROLS INDOOR UNIT (Cold or hot) Air Out OUTDOOR UNIT Service Cover Remove this cover to access the AC connection from this unit to the indoor unit. A B1 B2 5 Service Valve The indoor units and outdoor unit are connected by copper tubes which are connected here.
DMB-3003LH 2003.3.4 9:57 AM 페이지6 INDOOR UNIT DISPLAY Indoor Unit Display Switch Panel ■Remote Control Signal Receiver This place is the part to receive the signal if it receives the signal, you can hear the signal “beep”. EMR. REMOCON ON (Red) Lights-on during the operation Timer (Yellow) Lights-on during the time of reservation mode. Air clean (Green) Lights-on during the operation Quick (Red) Lights-on during the time of Quick Mode.
DMB-3003LH 2003.3.4 9:57 AM 페이지7 REMOTE CONTROLLER DMB-3003LH Display Displays information pertaining to unit. AUTO FAN SPEED Button Press to select the fan speed (High " ", Middle " ", Low " "). MODE Button Press to cycle through the modes (Auto/Quick/Cool/Fan/Dehumidifier/Heat) SLEEP Button Press to set the unit for the sleep mode. ON/OFF Button (Red) Press to turn the unit on or off. TEMPERATURE Buttons Press to raise or lower the desired temperature. MODE FAN SPEED FAN DIR. SLEEP FAN DIR.
DMB-3003LH 2003.3.4 9:57 AM 페이지8 OPERATION CONNECTING THE AC CORD Only the power plug of outdoor unit is connected to AC outlet, and the power of indoor units were supplied with AC connection cords from outdoor unit. To supply the system with AC power, follow the procedures bellow: 1. Insert the AC plug of outdoor unit into a pronged 220V AC outlet NOTES: • Never connect the AC line cord plug to other than the specified voltage (220V). • The new air conditioner system should be on it’s own 220V circuit.
DMB-3003LH 2003.3.4 9:57 AM 페이지9 HOW TO INSTALL BATTERIES To install the batteries, follow the procedures below: TIMER ON/OFF ENTER/ CANCEL TURBO/MILD + – 2. Insert two “AAA” size Alkaline batteries following the polarity diagram below. 1. Slide down the cover to access most of the remote buttons. Slide down further to access the battery compartment. – + BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1.
DMB-3003LH 2003.3.4 9:57 AM 페이지10 TO SET AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Follow procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Make sure the AUTO indicator AUTO appears in the remote display.
DMB-3003LH 2003.3.4 9:57 AM 페이지11 TO SET ONLY FAN MODE To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Fan indicator appears in the display. No allowance setting temperature 3. To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see below).
DMB-3003LH 2003.3.4 9:57 AM 페이지12 TO SET HEAT MODE To set the unit to heat the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Heat indicator appears in the display. In the heat mode, the fan direction ▼ or ▲ is further downward than that in the cool mode for the good circulation. 3. Using the TEMP.
DMB-3003LH 2003.3.4 9:57 AM 페이지13 TO SET ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 12, 16, 20, 24. 1. Press the ON/OFF button of timer on the remote control to set the on timer mode, “HOUR” and “ON” on the remote display will be displayed and “TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time.
DMB-3003LH 2003.3.4 9:57 AM 페이지14 TO SET SLEEP MODE When you are going to sleep, select this feature and the unit will cool off the room to the desired temperature and then increase that temperature throughout the night. 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button to select the desired mode. Then, set the desired temperature using the TEMP. ▲ or ▼ buttons. 3.
DMB-3003LH 2003.3.4 9:57 AM 페이지15 INSTALLATION DIAGRAM Below is an overview for the connection of the Indoor unit to the Outdoor unit. The pages following will give detailed instructions for full installation. Remember to read the complete Installation section and follow all the safety instructions fully when installing the Indoor and Outdoor units. OVERVIEW This appliance must be installed according to national power supply acquirement. 10cm (3.95in) from ceiling 30cm (11.8in) from side wall 10cm (3.
DMB-3003LH 2003.3.
DMB-3003LH 2003.3.4 9:57 AM 페이지17 CHANGING/CLEANING THE AIR FILTERS To change or clean the two black air filters, follow the procedures below: 1. Open the indoor unit’s cover and remove both black air filters by bending them slightly backward and the lifting out. 2. Remove the two small filters (Deodorizing and Electrostatic) from the indoor unit. 3. Examine the filters and determine if they need to be cleaned or replaced. To clean filters, use a vacuum and clean off dust.
DMB-3003LH 2003.3.4 9:57 AM 페이지18 CARE AND MAINTENANCE warning • Make sure the AC cord is unplugged and the unit is off before cleaning. • Do not use water on the unit to clean it. This is a shock hazard and the unit can be damaged. Clean the casing and front of the indoor unit with a vacuum brush or wipe with a clean damp cloth. • NEVER USE Solvents, harsh chemicals or hot water to clean the unit. • Some metal edges on the unit are sharp. Be careful when cleaning or handling.
DMB-3003LH 2003.3.4 9:57 AM 페이지19 TROUBLESHOOTING GUIDE Before requesting service, please refer to the chart below for possible solutions: SYMPTOMS No power . POSSIBLE CAUSE POSSIBLE SOLUTIONS Power failure. Restore the power Line voltage too low. Contact electrician to install new outlet. Unit is unplugged or not completely plugged in. Insert plug all the way. Unit is off. Turn unit on. Batteries in remote are weak or dead. Replace remote’s batteries.