OWNER'S MANUAL MODEL #: DSB-F183L S1 S/N : 3113909900
SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE INSTALLING AND OPERATING THE UNIT: This air conditioner meets strict safety and operating standards. The installer of this unit must install or service this unit so it operates safely and efficiently. Precautions When Wiring: • Do not plug in the unit until all connections (tubing, drain hose, mounting, etc.) have been made and double-checked. • High voltages are present in this unit and are very dangerous.
OPERATING SECTION LOCATION OF CONTROLS INDOOR UNIT Electric Dust Collector (Air clean Plasma) Removes small dust and generates (-) ions. Deodorizing Filter Removes bad smells from the air. AIR IN Sensor Wire Indoor Cover Air Cleaning Filters Removes dust and prohibits germs. AIR OUT Remote Sensor Fan Direction (Left/Right) Fan Direction (Up/Down) Emergency/Remote Switch Indicators Indicate the AC setting. FA FA MO N SP SL EE P TIM ON LCD Remote Controller EE N DIR .
INDOOR UNIT DISPLAY Indoor Unit Display Switch Panel ■Remote Control Signal Receiver This place is the part to receive the signal if it receives the signal, you can hear the signal “beep. beep”. REMOCON EMERGENCY REMOCON EMERGENCY Air clean (Green) ON (Red) Lights when the operation is going on. Timer (Yellow) Lights during the time reservation mode. ■There is a switch panel at inside of Front Panel. At the time of operating, open the Front Panel. Quick (Red) Lights during the time Quick Mode.
REMOTE CONTROLLER DSB-F183L Display Displays information pertaining to unit. AUTO FAN SPEED Button Press to select the fan speed (High " ", Middle " ", Low " "). MODE Button Press to cycle through the modes (Auto/Quick/Cool/Fan/Dehumidifier) ON/OFF Button (Blue) Press to turn the unit on or off. TEMPERATURE Buttons Press to raise or lower the desired temperature. MODE FAN SPEED FAN DIR. SLEEP FAN DIR. Button Press to select up/down direction for fan.
OPERATION CONNECTING THE AC CORD The outdoor unit is connected to the indoor unit through the AC connecting wire or connection cord. To connect the indoor unit to AC, follow the procedures below: 1. Insert the attached AC plug into a 2-pronged Only 220V or 220V~240V AC outlet. NOTES: • Never connect the AC line cord plug to other than the specified voltage (Only 220V or 220V~240V). • Use the attached power cord only. • If the outlet is a 3-pronged type or other, have an electrician install a new outlet.
SETTING THE UNIT FOR REMOTE OPERATION After the unit is fully connected and plugged in, it can be turned on. To turn the unit on and set it for remote operation, follow the procedures below: 1. Open the indoor unit’s cover and make sure the EMERGENCY/REMOTE switch is set to the REMOTE position; this will allow the unit to operate with the remote controller. EMERGENCY/REMOTE Switch 2. Press the ON/OFF button on the remote controller to turn on the unit.
SET UNIT TO QUICK MODE To set this unit to cool or heat (Heat pump model only) at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Quick (“ cator blinks. ”) indi- 3. The unit will then start cooling or heating the room at the highest power.
TO OPERATE ONLY FAN To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Fan indicator appears in the display. No allowance setting temperature 3. To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see below).
TO SET UNIT TO HEAT MODE (ONLY HEAT PUMP MODEL) To set the unit to heat the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Heat indicator appears in the display. In the heat mode, the fan direction (UP, DOWN) is further downward than that in the cool mode for the good circulation. 3. Using the TEMP.
TO SET THE ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 12, 16, 20, 24. 1. Press the ON/OFF button of timer on the remote control to set the on timer mode, “HOUR” and “ON” on the remote display will be displayed and “TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time. Then, if pressing “ENTER/CANCEL” button, ON TIMER Mode will be started.
TO SET THE OFF TIMER MODE This unit can be set to automatically turn off after a predetermined amount of hours (up to 12) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10, 11, 12. 1. Press the ON/OFF button of timer on the remote control to set the off timer mode, “HOUR” and “OFF” on the remote display will be displayed and “TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time.
TO SET UNIT TO SLEEP MODE When you are going to sleep, select this feature and the unit will cool off the room to the desired temperature and then increase that temperature throughout the night. 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button to select the desired mode. Then, set the desired temperature using the TEMP. ▲ or ▼ buttons. 3.
CHANGING/CLEANING THE AIR FILTERS To change or clean the two black air filters, follow the procedures below: 1. Open the indoor unit’s cover and remove both black air filters by bending them slightly backward and the lifting out. 2. Remove the two small filters (Deodorizing and Electrostatic) from the indoor unit. 3. Examine the filters and determine if they need to be cleaned or replaced. To clean filters, use a vacuum and clean off dust. Use water and mild soap also if necessary. 4.
CLEANING THE INDOOR COVER To clean the indoor cover, follow the procedures below 1. Remove the left and right side to open the indoor cover upward by two hand 2. Open the door until 80 degree 80° NOTE: Please remove and insert the indoor by two hand 3. Pull right side to remove indoor cover hinge from frame grille hinge hole 4. Remove the indoor cover 5. Cleaning the indoor NOTES: • Wipe the indoor cover with soft sponge or soft cloth.
CARE AND MAINTENANCE warning • Make sure the AC cord is unplugged and the unit is off before cleaning. • Do not use water on the unit to clean it. This is a shock hazard and the unit can be damaged. Clean the casing and front of the indoor unit with a vacuum brush or wipe with a clean damp cloth. • NEVER USE Solvents, harsh chemicals or hot water to clean the unit. • Some metal edges on the unit are sharp. Be careful when cleaning or handling.
TROUBLESHOOTING GUIDE Before requesting service, please refer to the chart below for possible solutions: SYSPTOMS No power. POSSIBLE CAUSE POSSIBLE SOLUTIONS Power failure. Restore the power Line voltage too low. Contact electrician to install new outlet. Unit is unplugged or not completely plugged in. Insert plug all the way. Unit is off. Turn unit on. Batteries in remote are weak or dead. Replace remote’s batteries. EMERGENCY/REMOTE switch is not set to REMOTE.
INSTRUCTION OF INSTALLATION Below is an overview for the connection of the Indoor unit to the Outdoor unit. OVERVIEW This appliance must be installed according to national power supply acquirement. 10cm (3.95in) from ceiling 30cm (11.8in) from side wall 10cm (3.95in) from side wall Wall Wall Bracket Drain Hose Wall Cap Oxygen tube At least 30cm (11.
