Owner’s Manual ENGLISH DVD-VIDEO PLAYER [Hi-Fi Model] DV–6T834B / DV–6T844N / DV–6T844B / DV–6T955B / DV–6T975B / DV–6T985B / DV–6T999B / DV–6T999N [Mono Model] DV–6T534N / DV–6T534B / DV–6T544N / DV–6T544B Downloaded From Disc-Player.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. PRODUCT INFORMATION IMPORTANT SAFEGUARDS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
IMPORTANT SAFEGUARDS FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user. 1 Read Instructions All the safety and operating instructions should be read before the unit is operated.
IMPORTANT SAFEGUARDS 810 of the National Electrical Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See example as shown.
1. PRODUCT INFORMATION Important Safeguards ................................ 1 Contents ................................................... 5 Features... ................................................. 6 Read Carefully Before Using ..................... 7 Identification of Controls .......................... 8 Remote Control ...................................... 12 2. INSTALLATION Connecting to a TV .................................. 14 Connecting a Cable Box .........................
FEATURES...
Please read carefully before using this DVD player. Placement and handling • The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc. • Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.
IDENTIFICATION OF CONTROLS Front Panel DV-6T834B ! @ # 3 $ % DV-6T844B DV-6T955B Downloaded From Disc-Player.
! Power button Use to power the device on/off if AC power supply is connected. @ Use to insert videotape # Disc tray $ Video input jack % Audio input jacks ^ VCR Eject button & Record button * Channel DOWN/UP buttons ( Operation Display Window OF CONTROLS 1 DVD Eject button 2 Rewind button Use to rewind videotape or skip to the previous chapter of a disc. 3 PLAY/PAUSE button Use to start and pause playback of videotape or disc. 4 Stop button Use to stop playing.
IDENTIFICATION OF CONTROLS Operation Display Window - RECORDING MODE - - REPEAT MODE - Timer Recording on Standby Repeat one chapter Timer Recording Error Repeat all chapters Recording in Progress Repeat a defined period from A Timer Recording in Progress Repeat a defined period from A to B Recording Pause - DVD OPERATION - - VCR OPERATION - DVD playback VCR playback Fast playback Fast forward Fast reverse playback Rewinding Slow playback Fast playback (CUE) Still picture Fast reve
OF CONTROLS Rear Panel Hi-Fi Model DVD & VCR DVD OUT AUDIO OUT COMPONENT OUT ANT.IN IN Y R R AUDIO Pr S-VIDEO OUT L COAXIAL RF OUT L Pb DIGITAL AUDIO OUT VIDEO Mono Model DVD & VCR DVD ANT.IN AUDIO OUT COMPONENT OUT Y R OUT Pr S-VIDEO OUT L COAXIAL AUDIO RF OUT Pb DIGITAL AUDIO OUT ! Power Cord IN VIDEO % S-Video Output Jack ^ A/V Output Jack & A/V Input Jack * Connection to Antenna/Cable ( Connection to TV Connect to wall outlet.
REMOTE CONTROL Switches the DVD+VCR on or off. [DVD] Opens/closes the disc tray, [VCR] Ejects a tape Changes to VCR mode. Changes to DVD mode. [VCR] Selects the devices connected to the Audio/Video sockets (RF, AV1, AV2). [VCR] Manually reduces of streaks or picture "jitter". Number entry [DVD] Activates Progressive Scan button, [VCR] Number 100 button Navigate through the menus., [VCR] Channel Up/Down button Confirms a menu selection. [DVD] Removes any menu or display from the screen.
Starts playing a disc or a tape. Pauses playback or recording modes. Starts fast reverse, reverses accelerated play or reverses slow motion Starts fast forward, forward accelerated play or forward slow motion Stops play, accelerated search, slow motion or recording.
CONNECTING TO A TV ■ The default RF Output channel is CH3. If Channel 3 is used by a TV station, you must change it to Channel 4. See "To Set Output Channel" on page 25. Various methods of connecting your TV Rear Panel of DVD+VCR DVD & VCR DVD OUT AUDIO OUT COMPONENT OUT ANT.IN IN Y R R AUDIO Pr S-VIDEO OUT L COAXIAL DIGITAL AUDIO OUT ANT INPUT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RF OUT L Pb VIDEO Method 1 A/V INPUT CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
CONNECTING A CABLE BOX How to connect RF Cable OUT Rear Panel of TV INPUT 1 INPUT 2 IN DVD & VCR RF Cable Cable Antenna Rear Panel of DVD+VCR INSTALLATION Cable Box/ Satellite Receiver OUT ANT.IN IN R AUDIO ANT IN RF OUT L VIDEO RF Cable AUDIO/VIDEO Cable 1 Connect the RF cable from the cable wall outlet to the RF In jack on your Cable Box. 2 Connect a second RF cable from the RF Out jack on the Cable Box to the IN (FROM ANT.) jack on the back panel of the DVD+VCR.
CONNECTING OTHER VIDEO EQUIPMENT ■ You can connect a wide variety of audio/video equipment to your DVD+VCR, including an additional VCR, Laser Disc Player, DVD Player, Camcorder, Satellite Receiver, or Video Game. Because these devices use all of connections, they are described together. How to Connect DVD & VCR DVD OUT AUDIO OUT COMPONENT OUT ANT.
CONNECTING TO A STEREO RECEIVER How to Connect INSTALLATION DVD & VCR DVD OUT AUDIO OUT COMPONENT OUT ANT.IN IN Y R R AUDIO Pr S-VIDEO OUT L COAXIAL RF OUT L Pb DIGITAL AUDIO OUT VIDEO ANT INPUT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.
CONNECTING TO A DOLBY DIGITAL DECODER OR DTS DECODER How to Connect DVD & VCR DVD OUT AUDIO OUT COMPONENT OUT ANT.IN IN Y R R AUDIO Pr S-VIDEO OUT L COAXIAL DIGITAL AUDIO OUT RF OUT L Pb VIDEO ANT INPUT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.
OUTPUT SELECT To Select DVD Press the [DVD] button. INSTALLATION "DVD" lights on the operation display window and all remote control buttons control the DVD player. To Select VCR Press the [VCR] button. BASIC OPERATION "VCR" lights on the operation display window and all remote control buttons control the VCR. To Watch TV or External Input Press the [TV VIEW] button. You can switch from VCR mode to TV mode (broadcasting reception) / external input mode (Video1,Video2) by pressing this button.
DVD PLAYBACK •If you do not close the tray, it will be closed automatically in 5 minutes to protect it from damage. •Some CD-R, CD-RW (MP3, AUDIO CD) may not play due to disparities in producing medium (PC, CD-Recorder), media type, and/or disc format. 1 2 3 Press [POWER√] to turn on the unit. 4 5 Press [OPEN/CLOSE] to close the tray. 6 7 8 To stop playback, press [ ]. Press [DVD] to select DVD mode. Press [OPEN/CLOSE] to open the disc tray.
DVD PLAYBACK Selecting an audio language ■ You may select an audio language if a disc includes multiple languages. Certain discs may not support audio selection. Keep pressing [AUDIO] until your preferred language appears in playback mode. ENG 01/03 If the DVD disc includes audio information, every time you press [AUDIO], English (ENG), French (FRE), Spanish (SPA), etc. appear one by one.
VCR PLAYBACK 1 2 3 4 Press [POWER√] to turn on the DVD/VCR. 5 Press [EJECT] on the unit or [OPEN/CLOSE] on the remote control to eject the tape. Press [VCR] to select VCR mode. Insert the desired tape. To start playback, press [PLAY]. If the picture is flickering or poor quality, adjust it with the [TRACKING +/–] buttons. To stop playback, press [ ]. To pause playback, press [PLAY]. Press [PLAY] again to resume playback.
CLOCK SET Press [VCR] on the remote control to select VCR mode. Press [SETUP]. Press [ENTER] to select “CLOCK SET”. “Time and Date Set” is already selected. Press [ENTER]to set the time and date. SETUP CLOCK SET TIMER RECORDINGS CHANNEL SET FUNCTIONS LANGUAGE SELECT Move: End: SETUP BASIC OPERATION 1 2 3 Set the TV to CH 3 (or 4). Select: ENTER CLOCK SET Time and Date Set Auto DST : ON Move: End: SETUP 4 Set the current date and time by pressing [œ √…†] keys or pressing the [0-9] keys.
MEMORIZING TV CHANNELS To Automatically Memorize Channels ■ Memorizing channels allows you to use the [CH+/-] button without seeing empty channels. You can manually delete channels you do not want to watch. 1 Press [VCR], then press [SETUP]. 2 Select “Auto Channel Search”. Press [†(CH-)] to move the to “CHANNEL SET”, and then press [ENTER]. Press [ENTER] to select “AUTO CHANNEL SEARCH”. Select “Detect Automatically”. Press [ENTER] to detect the channel automatically.
MEMORIZING TV CHANNELS To Delete Channels Manually ■ To delete memorized channels: 1 Press [VCR], then press [SETUP] and select ADD/REMOVE CHANNELS “CHANNEL SET”. Select “Add/Remove Channels”. Channel 02 is now REMOVED. 2 Select the desired channel and delete it. Use the [0-9] buttons to select the desired channel to delete. When [œ ] is pressed, “ADDED” under the channel number changes to “REMOVED”. 3 To check the deleted channel, press [CH+/–] on the remote control.
RECORDING To Record With VCR 1 Press [POWER√] to turn on the DVD/VCR. 2 3 4 5 6 7 Insert a recordable tape. • Press [VCR] to select VCR mode. • Turn on the TV and select Ch 3, or press [INPUT] on your TV to select External Input mode. Insert a tape with recording tab. With [CH+/–], [0-9] and [TV VIEW] buttons, select the desired channel or external input to record. Select the desired speed (SP or SLP) with the [SPEED] button. Press the [REC] button. The unit starts recording.
RECORDING To Record From DVD To Videotape during DVD playback 1 Press [DVD] to select DVD mode. Insert the desired DVD disc. You cannot record copy-protected DVD discs. Insert a recordable tape into the VCR. 2 Press [PLAY] to start the DVD playback and press [REC] to start the VCR recording. 3 To exit record, press [ ]. Recording stops automatically when recorded tape reaches the end. Video recorded in PROGRESSIVE SCAN mode will playback abnormally.
TIMER RECORDING Timer Recording 1 2 3 4 5 Turn on the TV. Make sure the current time is set correctly (see page 23 for instructions on setting the clock). Insert a recordable tape with recording tab. Press [VCR] to select VCR mode. Press [SETUP] and select “TIMER RECORDINGS”. Move to “TIMER RECORDINGS” with [†] and press [ENTER]. SETUP CLOCK SET TIMER RECORDINGS CHANNEL SET FUNCTIONS LANGUAGE SELECT Move: End: SETUP 6 Select “Make a New Program”. Press [ENTER] to select “Make a New Program”.
TIMER RECORDING 9 Set Date and Time to Record. Select the date, start time and end time to record using [0-9]. PROGRAM1 (ONE TIME) Channel Start Date Start Time End Time Tape Speed Move: Video: TVview 10 11 Select either SP, SLP or AUTO with [†] or […]. For more information on recording speed, see “Using video cassette” on page 30. Press [SETUP] to complete the Timer Recording. “Program # has been saved. For program recording, insert a cassette....” message is displayed.
TIMER RECORDING Timer Program Setting Press [PROGRAM] in VCR mode. This is a shortcut to view the Timer Recording menu. Before setting a Timer Recording, the clock should be set correctly and VCR mode should be selected. Types of Timer Recordings One Time: A single Timer Recording on a specific date and time. Daily : A Timer Recording that will record at the same time every day. Weekday : A Timer Recording that will record at the same time Monday through Friday.
WATCHING AND RECORDING CABLE TV ■ Because of the nature of converter boxes, you cannot watch one Cable TV channel and record another at the same time. To Watch and Record Cable TV 1 Turn on the cable box and then set a channel to watch or to record. Turn on the DVD+VCR and then set the DVD+VCR channel connected to the converter (CH03/04/EXTERNAL INPUT). Power on TV and then set the channel connected to the DVD+VCR (CH03/04/VCR).
USING ADVANCED VCR FEATURES Auto Playback ■ With Auto Play turned on (the factory default setting), the DVD+VCR player automatically starts playback when you insert a tape with its safety tab removed. 1 SETUP Press [SETUP] and select “FUNCTIONS”. CLOCK SET TIMER RECORDINGS CHANNEL SET FUNCTIONS LANGUAGE SELECT Move to “FUNCTIONS” with [†] and press [ENTER]. Move: End: SETUP 2 FUNCTIONS Press [ENTER] to switch between ON and OFF.
USING ADVANCED VCR FEATURES Searching a cassette tape for programs (indexing) ■ When you record a program, the VCR places an index mark at the start of the recording. To search for an index mark: FUNCTIONS 1 Press [SETUP] and select “FUNCTIONS”. 2 INDEX SEARCH If you want to scan through a certain number Press REW or FF of index marks, use the number buttons to to begin searching enter the number of marks you want to or Enter a specific search.
USING ADVANCED VCR FEATURES Set Auto Repeat ■ You can set the DVD/VCR to play the same segment of a tape over and over in a repeating loop. FUNCTIONS 1 Press [SETUP] and select “FUNCTIONS”. 2 The Set Auto Repeat menu will ask for a loop end time to be specified. To turn off Set Auto Repeat,press the [CLEAR] button. 1 2 Press [VCR], then press [SETUP] and select “CLOCK SET”. Select “Set Auto Repeat”.
USING ADVANCED VCR FEATURES Changing the setup menu language ■ You can set the language for VCR Setup menus to English, Spanish, or French. 1 Press [SETUP] button and select “LANGUAGE SELECT”. 2 Set the language to English, Spanish or French and [ENTER]. SETUP CLOCK SET TIMER RECORDINGS CHANNEL SET FUNCTIONS LANGUAGE SELECT LANGUAGE SELECT Select a language. English Spanish French Marking a tape for zero search to mark as 0:00:00. Pause the tape at this point.
HI-FI STEREO PLAYBACK Playing a tape in Hi-Fi high-quality • “Hi-Fi” appears at the top of the screen. • Pressing [AUDIO] changes the audio track as follows: Hi-Fi LINEAR MIX If there is noise in the recording, please select “Linear” to reduce it. Forced Mono • In some cases reception is poor when receiving stereo or SAP (Secondary Audio Program) audio signals. Press [AUDIO] to improve this poor audio quality by changing to mono sound.
PLAYING A DESIRED SCENE To skip scenes on a disc DVD, VCD, VCD2.0, CD, MP3 To skip to the next chapter (or track), press [ √√❚ ]. The current chapter (or track) skips to the next chapter (or track). To skip to the previous chapter (or track), press [❚œœ ]. The current scene skips to the previous chapter (or track) or to the first scene of the current chapter (or track). Jumping directly to a desired title DVD ■ Some movie discs contain multiple titles.
PLAYING A Repeating chapters, titles, and tracks DESIRED SCENE DVD, VCD, CD, MP3 In playback mode, pressing [REPEAT] more than once changes the repeat action as follows: - VCD TRACK ➝ ➝ DISC ➝ OFF REPEAT ALL ➝ ➝ OFF REPEAT ONE ➝ ➝ TITLE ➝ CHAPTER - CD/MP3 ➝ - DVD - RANDOM ➝ • CHAPTER : Current chapter will play repeatedly. • TITLE : Current title will play repeatedly. • TRACK : Current track will play repeatedly. • DISC : Current disc will play repeatedly.
PLAYING A DESIRED SCENE Searching a DVD by Title, Chapter or Time The current and total number of chapters are displayed. Use the [0-9] buttons to enter the desired chapter number. 4 When finished, press [ENTER]. ➟ current chapter 001/023 total chapter 01:03:20 ➟ 3 If you want to search for a time, press [SEARCH] three times. total title ➟ If you want to search for a chapter number, press [SEARCH] twice. 001/003 ➟ 2 The current and total number of titles are displayed.
PLAYING A DESIRED SCENE Storing bookmarks in memory to be viewed (listened to) again DVD ■ Storing a bookmark in the DVD memory is similar to marking your page in a book. It allows you to quickly return to any point on the disc. Marks are not permanent. They are erased from the DVD memory when you eject the disc or power off the DVD. 1 Storing a marker in the memory. 2 Recalling/Clearing a marker Downloaded From Disc-Player.
CONFIRMING CURRENT PLAY MODE Confirming the current disc mode While in Play mode, press [DISPLAY]. The current disc mode is displayed. If you want to change the mode, select the item with […] or [†] and enter the new settings with the [0-9], [œ] or [√] buttons. When finished with each change, press [ENTER]. To exit Display mode, press [DISPLAY] again.
ZOOM, MULTI ANGLE AND 3D AUDIO Using the zoom function DVD, VCD ■ You can enlarge the current screen 2 or 4 times. In the case of SVCD and VCD, only 2 times Zoom is available. Keep pressing [ZOOM] until the preferred level of magnification appears. Each you press [ZOOM], the zoom magnification changes 2 times (X2) ➝ 4 times (X4) ➝ OFF ➝ 2 times (X2) ➝ ... The default zoom position is the center of the screen. You can move this point using [œ √…†].
ABOUT MP3, JPEG DISCS Playing a disc containing MP3 files MP3 ■ This unit will play MP3 files recorded on CD-R and CD-RW discs. 1 Press [OPEN/CLOSE] to open the disc tray. Place a disc with MP3 files on the disc tray with the label side up. Press [OPEN/CLOSE] to close the disc tray. The DVD+VCR will load the disc and display the directory structure. 2 The following screen appears.
ABOUT MP3, JPEG 6 You can program playback. Select the file in LIST folder. Then press [PROGRAM]. The selected file will go into PROGRAM folder. Press [PLAY] in PROGRAM folder. If you want to move all the files in LIST folder to PROGRAM folder, select and press [ENTER]. MUSIC > MP3 √ 001/018 0:00:34 / 0:03:59 LIST __ 1. 01(musicfamily.i 2. 02(musicfamily.i 3. 03(musicfamily.i 4. 04(musicfamily.i 5. 05(musicfamily.i 6. 06(musicfamily.i 7. 07(musicfamily.i DISCS REPEAT ONE PROGRAM 6. 06(musicfamily.i 2.
ABOUT MP3, JPEG DISCS Playing a disc containing JPEG (PHOTO) files JPEG ■ This unit will play JPEG files recorded on CD-R and CD-RW discs. It will also play JPEG files recorded on DVD, DVD-R, DVD-RW, and DVD+RW. 1 Select the desired folder. PICTURE > JPG ■ 000/000 0:00:00 / 0:00:00 Move the cursor to the desired folder by pressing […†] and press [ENTER] to confirm. LIST DESKTOP PHOTO TEMPORAR TRASH PREVIEW \ 2 Slideshow Delay Time set.
DISPLAYING DISC MENUS To display disc menus 1 DVD, VCD2.0 Press [TITLE/PBC] or [MENU]. • The disc menu is displayed. These menus vary by disc. (“Return” will appear on the OSD with VCD2.0.) • If it is a VCD2.0, select PBC ON mode by pressing [TITLE/PBC]. * CD and VCD1.1 do not have menus. 2 Move the cursor to the desired menu item with [œ √…†] and select with [ENTER] or [PLAY]. PROGRESSIVE SCAN MODE Selecting SCAN MODE DVD While in DISC STOP mode, press and hold the [P.
DVD LANGUAGE SETUP ■ You can set your preferred language for disc menus, audio soundtracks and subtitles. If a disc does not include language information, the selected language will not appear. 1 While in Stop mode, press [SETUP]. 2 Selecting an OSD language. 3 Selecting an AUDIO language. Select a OSD language to be displayed on DVD menus with [ENTER]. Set your preferred audio language with [ENTER].
DVD LANGUAGE SETUP 5 Selecting a DISC MENU language. Set your preferred DISC MENU language with [ENTER]. If the DISC MENU language is set and recorded on the DISC, it is automatically played in the set language every time it is played. OTHERS - - - - : Another language can be selected. You can input 4-digit language code.
VIDEO SETUP ■ To set the DVD+VCR to match the capabilities of your TV: 1 While in Stop mode, press [SETUP]. TV ASPECT VIDEO OUT SCAN MODE 4:3 LB COMPONENT INTERLACED 2 Selecting TV ASPECT. TV ASPECT 4:3 LB 3 Selecting VIDEO OUT. ✓ VIDEO OUT 4:3 PS If you select “4:3 LB”, you can watch the SCAN MODE 16:9 WIDE original widescreen movie, but black bars will appear above and below the picture. If you select “4:3 PS”, the picture will fill the screen but the sides of the movie will be cropped.
AUDIO SETUP ■ To set the DVD+VCR to match the capabilities of your audio system: Downloaded From Disc-Player.com Daewoo Manuals 50 1 While in Stop mode, press [SETUP]. DIGITAL OUT DYNAMIC RANGE 2 Selecting DIGITAL OUT. DIGITAL OUT BITSTREAM DYNAMIC RANGE LPCM 3 Select a Dynamic Range BITSTREAM OFF ✓ Set audio output to coaxial or optical. You can set the outgoing digital signal to BITSTREAM or LPCM: • BITSTREAM : The raw audio signal recorded on the disc goes to the digital audio output.
OTHERS SETUP 2 Selecting OSD. 3 Selecting SCREEN SAVER. 4 Restoring DEFAULTS. 5 Selecting PARENTAL. Select "ON" to have the OSD (On Screen Displays) shown on the screen. To protect your TV from possible damage from bright scenes over long periods of time, you can turn on the built-in screensaver. When set to "ON", the screensaver functions automatically whenever the unit is left in Stop for 5 minutes. If you press [ENTER] when the cursor highlights RESET, “Are you sure?” message will appear.
OTHERS SETUP •If the password is wrong, “WRONG PASSWORD” appears instead of “CHANGE PASSWORD”. •The initial Password is “3308”. If you forget your new password, you may input this number. 6 Changing a password. To change your password, move the cursor to “PASSWORD” and press [√]. Enter your current password. ---- Then enter a new password and press [ENTER]. Now your password is changed. 52 INPUT PASSWORD OK Confirm the new password by typing it again. Downloaded From Disc-Player.
ABOUT DVD Playable Discs • DVD, Video CD (Version 1.1, 2.0), S-VCD and Audio CD Disc type Playable Restriction DVD Video CD Yes Yes Region number 1 or Region number All Version 1.0/1.1/2.
ABOUT DVD CHAPTER Information recorded on a DVD. A title on a DVD is divided into many tracks, each of which are referred to as chapters. Each chapter is numbered and can be searched using its number. TITLE Information recorded on a DVD. A DVD can be divided into may titles. TRACK Information recorded on a video CD or audio CD. A disc consists of many tracks. Each track is numbered and can be searched using its number. dts Digital Theatre System is a 5.
ABOUT VCR AND VIDEOTAPE VCR Terms AFT Automatic fine tuning, a circuit that automatically adjusts TV reception to optimum condition. CABLE Cable television. Index Search A feature of this VCR that automatically records an index mark each time recording begins. It helps you locate a particular segment of the tape quickly and easily.
TROUBLESHOOTING (DVD) Symptom • The player does not play. ➤ If a DVD is from overseas, it may not play. Make sure the DVD’s region code is 1 or All. ➤ Make sure the DVD is inserted in the right direction. ➤ If it is a CD-ROM or DVD-ROM for a PC, it will not play. • No sound. ➤ Play mode may be slow or paused. (In variable speed play, no sound comes through) ➤ Check audio connections. ➤ Make sure TV and amplifier are working correctly. ➤ Check "AUDIO" items in the SETUP menu.
TROUBLESHOOTING (VCR) Symptom Checks ➤ Make sure the power plug is inserted in an electric outlet. • Unit does not work even in “Power On”. ➤ Make sure a videotape is inserted. ➤ Press [VCR] on the remote control or press DVD/VCR on the front panel of the unit. ➤ Unplug the unit and plug it in again. • A videotape will not insert. ➤ Make sure a power plug is inserted in an electric outlet. ➤ Make sure a videotape is not already inserted.
TROUBLESHOOTING (VCR) Symptom • A screen in Pause mode is shaking or slow playback is not clear. ➤ Try using a head-cleaner. ➤ Try using the [TRACKING+/–] buttons. • The unit will not record a TV program. ➤ Check whether the desired channel is visible on the screen. If not, press [TV VIEW] to view the TV. ➤ Check whether the timer recording settings are right.
SPECIFICATIONS Power requirement AC 120V, 60Hz Power consumption 24W (supplementary 4W) Weight 9.9 lbs (4.5kg) Dimensions (WxHxD) 17.1" x 3.7" x 10.0" (435mm x 93mm x 255mm) Operating temperature 41°F~95°F (5°C~35°C) Installation conditions Horizontal / Relative humidity under 80% Channel coverage VHF: 2-13 CH / UHF: 14-69 CH / Cable: 1-125 Signal type NTSC COLOR Antenna Input/output U/V-mixed: 75Ω unbalanced VIDEO input 1.0 Vp-p unbalanced, RCA JACK AUDIO input -8.
WARRANTY DEAM (Daewoo Electronics America) warrants each new electronic product manufactured by it to be free from defective material and workmanship and agrees to remedy any such defect or to furnish a new part (at the Company’s option) in exchange for any part of any unit of its manufacture which under normal installation, use and service disclosed such defect, provided the unit is delivered by the owner to us or to our authorized distributor from whom purchased or authorized service station intact, for o