ROOM AIR CONDITIONER USE & CARE MANUAL WINDOW TYPE ROOM AIR CONDITIONER MODEL #: UL and CUL listed C DWC-055RL DWC-063RL R LISTED US Please read carefully and thoroughly this manual before operating the unit. If you still have any difficulties or problems, consult your dealer for help or ELECTRONICS. Please keep this manual well.
PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER Please observe the following instructions. 1. Operate the Selector Switch to run or stop the unit. - Do not use Main Power Switch or Auxiliary Power Switch to operate unit. 2. Do not stick anything into the air outlet or inlet. - It is dangerous and it can cause injury or damage. 3. Avoid exposing your body directly to a continuous cool air - flow for long periods. - It is not good for your health. 4. Do not pour water on the unit to clean it.
TABLE OF CONTENTS 1. GENERAL SPECIFICATIONS...............................................................................2 2. INSTALLATION INSTRUCTIONS.......................................................................
INSTALLATION INSTRUCTIONS • WINDOW REQUIREMENTS These instructions are provided for a standard double hung window or mobile home double hung window installation in windows 21.7in (550mm) to 34.6in (880mm). The upper and lower sash must open sufficiently to allow a clear vertical opening of 12.7in (323mm) from the bottom of the sash to the window stool. 22" TO 21.7” TO 36" 34.6” Select a centrally located window on the side of the room that 12.7” MINMIN 14 1/2" receives the least direct sunlight.
• SAFETY INSTRUCTIONS The receptacle should be an individual branch circuit used only for this air conditioner. Be sure the electrical service is adequate for the model air conditioner you have chosen. The complete electrical rating of your air conditioner is stated on the name plate located at the unit’s side. Be sure the plug receptacle is close enough for the power cord to reach it.
• Step 1 - Prepare Components For Installation • SCREW TYPE 1. Open the components box for installation 2. Check components for installation as follows.
• Step 3 - Placing Unit in Window CAUTION 1. The unit is heavy. To avoid injury or accident, it is strongly recommended that you have additional help when lifting the unit. 2. Personal injury or property damage may result if unit falls from window. 1. Insert Window Kit Frame into the upper and bottom guides of the unit. 2. Fasten window shutter in the window kit frame with Screws (Type D) in the left side and right side of the unit. 3. Open the window and place the unit in the center of the window sill.
• Step 5 - Secure Window Shutter CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame. WINDOW KIT FRAME To provide a proper seal, pull each expandable side Window Shutter out and up until it is tight against the window frame. Using the hole in the top and bottom of each Window Kit Frame as a guide, secure Window Kit Frame in window sash and on the window sill.
NAMES OF MAJOR COMPONENTS 5 1 2 3 8 7 9 4 6 0 q 5 1 2 3 7 4 6 NO PART NAME NO PART NAME 1 CABINET 7 AIR FILTER 2 BLADE VERTICAL 8 FRAME GUIDE TOP 3 COOL AIR DISCHARGE 9 FRAME WINDOW KIT 4 GRILLE FRONT 10 SHUTTER WINDOW 5 PANEL CONTROL 11 REMOTE CONTROLLER 6 AIR INTAKE 8
OPERATION INSTRUCTIONS • DISPLAY MODE DISPLAY • It displays the operating mode. REMOTE SIGNAL RECEIVER TEMP./TIMER DISPLAY • It displays the temperature and the timer. FAN SPEED • Everytime you push this button, It is selected as follow. (Low→High→Low) ENERGY SAVE • Whenever you push this button, the cumulative power consumption is decreased. TEMPERATURE SET • It is the button to set the desired room temperature.
• REMOTE CONTROL REMOTE SIGNAL TRANSMITTER POWER ON/OFF • To turn the unit ON, push this button. To turn the unit OFF, push this button, again. TEMPERATURE • It is the button to set the room in the desired room temp. The temp. can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) MODE • Everytime you push this button, it is selected as follow. (COOLING→TURBO→FAN →COOLING) FAN SPEED • Everytime you push this button, it is selected as follow.
FUNCTION POWER ON POWER or Push POWER button OPERATION 1. The unit starts working. (It is delayed 3 minutes after main power source is supplied.) 2. Default mode is ‘COOLING’ mode. 3. Default desired room temperature is ‘26°C’ (79°F). And fan speed is ‘Low’. 4. When you tum off the unit with cooling mode, the Fan still work for about 10 seconds. COOLING MODE DISPLAY 1. Current room temperature is displayed. 2. ‘COOLING’ lamp lights. FAN ROOM TEMP. TEMP TURBO DESIRED TEMP.
FUNCTION FAN MODE MODE MODE or OPERATION DISPLAY 1. The Fan works only. 2. In this mode, the unit circulate room air. 3. Fan speed can be changed. 1. Current room temperature is displayed. 2. ‘FAN’ lamp lights. FAN TEMP Push the ‘MODE’ button until ‘FAN’ lamp lights. ON/OFF ENERGY SAVE ENERGY SAVE ENERGY SAVE or ROOM TEMP. TURBO DESIRED TEMP. COOLING ENERGY SAVE TIMER 1. Desired temperature is changed as follows by pushing ‘ENERGY SAVE’ button. 1. Current room temperature is displayed. 2.
FUNCTION ON TIMER TIMER/ CANCEL Push the ‘TIMER/CANCEL’ button when unit is off. (REMOCON ONLY) SLEEP MODE SLEEP Push the ‘SLEEP’ button in ‘COOLING’ mode. (REMOCON ONLY) OPERATION DISPLAY 1. Timer is changed to as follows by pushing “TIMER/CANCEL” button. (1hr→2hr→3hr→4hr→5hr→6hr→8hr→ 10hr→12hr→16hr→20hr→24hr→cancel) 2. The unit starts working after set time is over in cooling mode with last temperature set. 3. If you want to cancel timer, push this button again at any time. 1. ‘TIMER’ lamp lights.
• HOW TO INSERT BATTERIES 1 Remove the COVER from the back of the remote controller. • Slide the Cover according to the arrow direction 2 Insert two battaries. • Be sure that the (+) and (–) directions are correct • Be sure that both batteries are new — + 3 Re-attach the cover. • Slide it back into position + — • Do not use rechargeable batteries such batteries differ from standard dry cells in shape, dimensions, and performance.
GENERAL INFORMATION • CHANGING AIR FLOW DIRECTION Air flow deflectors divert air from center flow to left or right. Adjust deflectors for desired air flow pattern. • AIR FLOW AROUND UNIT Check in door grill and outdoor louvers for air flow obstructions. Do not block air flow to and from unit. The outdoor coil should be checked and periodically cleaned for debris that may collect and block unit air flow.
CARE AND MAINTENANCE CAUTION To avoid death or personal injury due to electrical shock, turn fan control OFF and unplug power cord before cleaning or performing maintenance. After cleaning or performing maintenance, reconnect power. • AIR FILTER Clean the air filter, which removes dust inside the room. It should be washed at least once every week during operation. 1. Remove the Air Filter from the front grill by pulling up. 2. Clean Air Filter with a vacuum cleaner or lukewarm, soapy water. 3.
ELECTRICAL REQUIREMENTS • ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong(grounding) plug for protection against possible shock hazards. If a two-prong wall receptacle is encountered, the customer is required to contact a qualified electrician and have the two-prong wall receptacle replaced with a properly grounded three-prong wall receptacle in accordance with the National Electrical Code.
BEFORE CALLING FOR SERVICE When you find something wrong with your room air conditioner, please carefully check the following items. If you are unable to find the cause of trouble, contact your service dealer. Difficulty Possible Cause Suggested Solution • Air conditioner does not operate. • No power to unit. • Confirm power cord is plugged in. • Verify main power switch (main circuit breaker) or fuse of the unit is good. • Little or no cooling • Compressor lockout on initial plug in.
Limited Warranty DAEWOO ELECTRONICS AMERICA, INC. warrants the following window room airconditioner to be free from defective material and workmanship and agrees to remedy any such defect or to furnish a new part (at the Company’s option) in exchange for any part of any unit of its manufacture which under normal installation, use and service disclosed such defect, provided the unit is delivered by the owner to store or dealer where purchased or Daewoo authorized service center.