Washing Machine Instruction Manual DWC-LU1011/121X, DWC-LD1411/161X, DWD-LU1011/121X, DWD-LD1411/161X DWC-LU102X/122X, DWC-LD142X/162X, DWD-LU102X/122X, DWD-LD142X/162X INSTRUCTION MANUAL ■ Economic wash system Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water level and washing time. ■ Low noise system The washer minimizes the washing and spinning noises by sensing the amount of laundry.
Contents Parts and features................................................................................................................3 Washer safety...........................................................................................................................4 Installation instructions...................................................................................................5 Inlet hose connection......................................................................................
Parts and features El The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer. NOTE The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book. Your model may not include all features.
Washer safety Save these instructions Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions. Read all instructions before using your washer • Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer. Do not add flammable fluids to your wash water. These substances give off vapors that can create a fire hazard or explosion.
Installation instructions El Removing transit bolts 1. Before operating the washer, remove the transit bolts(4ea) along with the rubber. • If the bolts are not removed, it may cause heavy vibration, noise and malfunction. 2. Unscrew the 4 bolts with the 10mm hex wrench or spanner or cross-tip screwdriver. Keep the 4 bolts for a later time. • When the appliance is transported, transit bolts will be re-used. 3. Close the holes with the cap holders supplied.
Inlet hose connection The washer should be connected to the water mains using new hose sets and old hose sets should not be reused. In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve. Option : Be careful not to confuse hot water inlet and cold water inlet. For Ordinary Tap Pull down the collar of the inlet hose to separate it from the water tap adapter. Loosen the four screws properly in order to fit into water tap.
Electrical requirements Electrical shock hazard Failure to follow these instructions could result in death or serious injury. WARNING • Electrical earth is required on this washer • If it does not fit the outlet, have a proper outlet installed by a qualified electrician. • Don’t earth to a gas pipe. • Don’t change the power supply cord plug. • Check with a qualified electrician if you are not sure the washer is properly earthed.
Electrical requirements (cont.) Adjust the level of washer using adjustable legs. • Please check if there is any gap between the four adjustable legs and the floor. • Adjust the level of washer by turning adjustable legs. And make it sure that there is no swaying of washer. • After the adjustment is finished, turn the fixing nuts up tightly so that the washermaintains the adjustment.
Operating your washer (cont.) Sorting • Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. • Separate dark colors from light colors, colorfast items from non-colorfast item. Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Color (White, Lights, Darks) Separate white clothes from colored clothes. Lint (Lint producers,Collectors) Wash lint producers and lint collectors separately. Loading • Drop items into washer loosely.
Option Steam(option) Water +(option) The functions of the control panel ■ DWC-LU101X/DWC-LU121X/DWC-LD141X/DWC-LD161X Option Low Temp Iron Cupboard Very Time Steam(option) Water +(option) Press this switch to turn the power on or off. Option Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; press the “Start/Pause” button → Select the program that you want to change → press the “Start/Pause” button again.
The functions of the control panel (cont.) ■ DWD-LU101X/DWD-LU121X/DWD-LD141X/DWD-LD161X Option Steam(option) Water +(option) Press this switch to turn the power on or off. Option Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; press the “Start/Pause” button → Select the program that you want to change → press the “Start/Pause” button again.
The functions of the control panel (cont.) ■ DWC-LU102X/DWC-LU122X/DWC-LD142X/DWC-LD162X Steam(option) Water +(option) Steam(option) Water +(option) Option Steam(option) Water +(option) Press this switch to turn the power on or off. Steam(option) Water +(option) Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; press the “Start/Pause” button → Select the program that you want to change → press the “Start/Pause” button again.
The functions of the control panel (cont.) ■ DWD-LU102X/DWD-LU122X/DWD-LD142X/DWD-LD162X Steam(option) Water +(option) Steam(option) Water +(option) Option Steam(option) Water +(option) Press this switch to turn the power on or off. Steam(option) Water +(option) Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; press the “Start/Pause” button → Select the program that you want to change → press the “Start/Pause” button again.
Washing procedure and program selection 1. Cotton is automatically selected upon power on • Press the Power button to start. • Press the Start/Hold button • Initial condition - Program : Cotton - Wash : main wash - Rinse : 3 times - Spin : DWC(DWD)-LU’S : 800 DWC(DWD)-LD’S : 800 - Water temperature : 40°C 2. MANUAL SELECTINg • Press the Power button to start • Select the conditions which you want to use by turning the program dial and pressing each button. • Press the Start/Pause button. 3.
Washing procedure and program selection (cont.) 4. Function • Recommended programs according to the laundry type Proper Temp. Option Maximum Load First check if laundry is machine washable.(white cotton, linen towel and sheets..) 60°C (Cold, 30°C, 40°C, 95°C) Pre Wash Rinse+ Rating Colorfast garments (shirts, night dresses, pajamas..) and lightly soiled white cottons (underwear..
Washing procedure and program selection (cont.) * Cotton/normal program 1 Put the laundry in to the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash and prewash compartments in the detergent case. Softener should be below the ‘MAX’ level. • Put detergent into the pre wash compartment only if you want to add prewash. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button.
Washing procedure and program selection (cont.) * Synthetic Program 1 Put the laundry in the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash and prewash compartments in the detergent case. Softener should be below the ‘MAX’ level. • Put detergent into the pre wash compartment only if you want to add prewash. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button.
Washing procedure and program selection (cont.) * Delicate / HANDWASH Program 1 Put the laundry in the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash compartments in the detergent case. Softener should be below the ‘MAX’ level. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button. • The LED shows only ‘---’ and all Program Lights turn on.
Washing procedure and program selection (cont.) * INTENSIVE PROGRAM 1 Put the laundry in the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash and prewash compartments in the detergent case. Softener should be below the ‘MAX’ level. • Put detergent into the pre wash compartment only if you want to add prewash. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button.
Washing procedure and program selection (cont.) * Quick 20 1 Put the laundry in the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash compartments in the detergent case. Softener should be below the ‘MAX’ level. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button. • The LED shows only ‘---’ and all Program Lights turn on.
Washing procedure and program selection (cont.) * Sports wear PROGRAM 1 Put the laundry in the drum. Put detergent and softener into the detergent case. Then close the door. • Put detergent into the main wash and prewash compartments in the detergent case. Softener should be below the ‘MAX’ level. • Put detergent into the pre wash compartment only if you want to add prewash. • When you want to use bleach, put it into the main wash compartment with detergent. 2 Press the Power button.
Washing procedure and program selection (cont.) * TUB CLEAN PROGRAM 1 Press the Power button. • The LED shows only ‘---’ signal. 2 Select the ‘Tub Clean’ program using program selection dial. • ‘Soak’ and spin ‘400’ rpm and ‘Cold’ water temperature. 3 Press Start/Pause button. • The washer will be operated with locking Door and supplying water. NOTE • All programs are not selectable. • Use this program WITHOUT load. • The appropriate cleaning time is one time per a month.
Washing procedure and program selection (cont.) * Drain PROGRAM 1 Press the Power button. •T he LED shows only ‘---’ signal. 2 Select the ‘Drain’ program using program selection dial. 3 Press Start/Pause button. •D rain program will start. NOTE • All programs are not selectable.
Guide for other useful programs * DELAY START(RESERVED WASHING) 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below ‘MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent.
Guide for other useful programs (cont.) * ONLY WASH 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. 2 Press the Power button. • The LED shows only ‘- --' signal. 3 Select the ‘WASH COURSE' you want by pressing ‘Wash' button. • The water temperature is selected to ‘Cold' automatically. 4 Press the ‘Start/Pause' button. • The washer will be operated with locking Door and supplying water.
Guide for other useful programs (cont.) * DRY (For DWC-LD1XXX , DWC-LU1XXX) 1 Put the laundry into the Drum and close the Door. 2 Press the Power button. • The LED shows only ‘- --' signal. 3 Select the ‘DRY CONDITION' you want by pressing ‘DRY' button. As this button is pressed, the dry condition is selected by ‘Cupboard' → ‘Very' → ‘Time(1:00, 2:00, 3:00, 4:00)' → OFF → ‘Low Temp' → ‘Iron' → ‘Cupboard' 4 Press the ‘Start/Pause' button. • The washer will be operated with locking Door.
Guide for other useful programs (cont.) * CHILD LOCK 1 Press the "Wash" and "Temp." button simultaneously during processing. 2 Under the Child Lock function, only power button is working. 3 During Child Lock function, CHL will be displayed on '18:88'. 4 In order to unlock Child Lock mode, press "Wash" and "Temp." simultaneously.
Maintenance Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. Cleaning your washer Exterior Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Occasionally wipe the outside of the washer to keep its looking like new one. Interior Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent. Run washer through a complete cycle. Repeat this process if necessary.
How to clean the filter Filter Frame Filter Frame Filter Lint Filter Filter Frame LintLint Filter Cleaning the water inlet filter Clean the filter when water leaks from the water inlet. Pull the power plug out before cleaning it. Turn off the water supply to the washer and separate the inlet hose. Pull the inlet filter out. Remove the dirt from the inlet filter with a brush. Cleaning the drain filter • This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..
Removing stains Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before washing. Stain removal rules • Use warm water for soaking or prewashing stained laundry. Hot water can set stains. • Most stains are easier to remove when they are fresh.
Trouble shooting Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service. If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first turn off the power of the washing machine and then turn on the power pressing Power button.
Specification MODEL DWC-LU1011/1211 DWD-LU1011/1211 DWC-LD1411/1611 DWD-LD1411/1611 Dimension (mm) 600 X 645 X 850 Maximum mass of textile (kg) 9 Kg Unit Weight (net/gross) Standard Water Consumption Spin Speed (RPM) Operating Water Pressure E-32 78/82 71/75 76/80 69/73 65 ℓ DWC(DWD)-LU10XX : MAX 1000 DWC(DWD)-LU12XX : MAX 1200 DWC(DWD)-LD14XX : MAX 1400 DWC(DWD)-LD16XX : MAX 1600 0.03MPa ~ 0.8MPa (0.
Wiring diagram O DWC-LD'S (OPTION) (OPTION) (OPTION) O DWD-LD'S (OPTION) (OPTION) (OPTION) E-33
Wiring diagram (cont.
English Português Disposal of Used Electrical & Electronic Equipment Eliminação de Equipamento Eléctrico e Electrónico Usado The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste.
esky Italiano Trattamento del dispositivo elettrico od elettronico a fine vita (Applicabile in tutti i paesi dell’Unione Europea e in quelli con sistema di raccolta differenziata) Likvidace pou it ch elektrick ch a elektronick ch za ízení Tento symbol na v robku, jeho p íslu enství nebo obalu ozna uje, e s tímto v robkem nesmí b t zacházeno jako s domovním odpadem. V robek zlikvidujte jeho p edáním na sb rné místo pro recyklaci elektrick ch a elektronick ch za ízení.
Svenska Dansk Omhändertagande av gamla elektriska och elektroniska produkter (Användbar i den Europeiska Unionen och andra Europeiska länder med separata insamlingssystem) Håndtering af udtjente elektriske og elektroniske produkter (Gælder for den Europæiske Union og andre europæiske lande med separate indsamlingssystemer) Symbolen på produkten eller emballaget anger att produkten inte får hanteras som hushållsavfall.
ABOUT THIS MANUAL VISION CREATIVE. INC. 서울 종로구 통의동 6번지 이룸빌딩 4층 담 당 이영배 님 F.MODEL BUYER B.MODEL DWDWC-LU1011/1211, LD-1411/1611, DWDWD-LU1011/1211, LD1411/1611 언 영어 어 BRAND 대우일렉 COUNTRY 1차 2차 일 정 3차 4차 5차 제 판 규 격 인 쇄 애드컴 MEMO 접수 : Quark data 받아서 인디자인 작업함 09. 08.