S/M No. : DWDM805101 Service Manual Washing Machine Model: DWD-M8051/M8052/M8053 DWD-M1051/M1052/M1053 ✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr). DAEWOO ELECTRONICS CORP. http : //svc.dwe.co.kr Feb.
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO W
1. SPECIFICATIONS ■ DWD-M805'S/M105'S INLET HOSE(HOT) (OPTION) INLET HOSE (COLD) DETERGENT CASE POWER CORD CONTROL PANEL DOOR HOSE DRAIN COVER PUMP ADJUSTABLE LEG MODEL DWD-M805'S / M105'S Power Source A.C 220~240V / 50Hz Power Consumption 2000 W Dimension (mm) 595 x 507 x 850 (WxDxH) Maximum mass of textile (kg) 6 kg Unit Weight (kg) 46(Net) / 49(Gross) Standard Water Consumption 42ℓ Spin Speed(RPM) 500 / 800 (1000) Operating Water Pressure 0.03MPA ~ 0.8MPa (0.
2. INSTALLATION ■ Removing transit bolts 1. Before operating the washer, remove the transit bolts(3ea) along with the rubber. • If the bolts are not removed, it may cause heavy vibration, noise and malfunction. 2. Unscrew the 3 bolts with the 10mm hex wrench or spanner or cross-tip screwdriver. Keep the 3 bolts for a later time. • When the appliance is transported, transit bolts will be re-used. 3. Close the holes with sticker holders supplied.
■ BS Plug Safety Details (For U.K.
■ Installation of drain hose • Never forget to install drain hose before operating your washer. • Open the packing box, and the drain hose is tied at backside of washer. • If you use the laundry tub, Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer. Laundry tub Tie strap min. 60 cm max. 100 cm Hose Retainer ca. 105 cm max. 100 cm min. 60cm max. 100 cm min. 60cm • When installing the drain hose to tub(sink), secure it tightly with a string.
3. MAINTENANCE ❈ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock hazards. Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. ■ Cleaning your washer Exterior • Clean with warm water and a neutral non abrasive household detergent. • Immediately wipe off detergent, bleach and other spills with a soft and damp cloth or sponge.
■ Cleaning the water inlet filter. • “IE” error message (refer to troubleshooting guide) will display when the water does not enter the detergent case. • If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. And the water leaks from the water inlet. • It is therefore a good idea to clean it from time to time. 1 Turn off the water tap. 2 Separate the inlet hose. 3 Pull out the inlet filter. Clean the inlet filter with the brush. 4 Connect the inlet hose.
■ Cleaning the detergent case. • In case of residual detergents or fabric softeners have accumulated ; - It should be cleaned with a jet of running water. - If necessary, it can be removed completely from the washing machine. Push point 1 Pull-out 2 Push and pull again • Detergents can be also accumulate the inside cavity. In this case, the inside cavity should be cleaned with a brush. • After cleaning, replace the detergent case and run Rinse cycle without laundry. ■ Cleaning the washing drum.
4. DIRECTION FOR DISASSEMBLY DOOR LOCK SWITCH 1 Open the door and remove the clamp door as. 2 Separate the gasket from the cabinet front and remove two screws. 3 Remove the door lock switch from the cabinet front . DRAIN PUMP 1 Separate the cover pump from the cabinet front and remove screw. 2 Lay the right-side of the washer on the floor. And separate connectors and hose drain from the pump. 3 Remove the hose drain o from the pump.
HEATER AND THERMISTOR 1 Separate the plate t as from the washer. (Remove two screws at rear) 2 Separate the case detergent as and remove two screws from panel f. 3 Separate the panel f as from the washer. 4 Separate the cabinet front from the washer. (Remove the clamp door as and 4 screws) 5 Separate connectors from the heater and remove the nut by using a box wrench. 6 Remove the earth terminal and loosen the nut by using a box wrench. 7 Pull out the heater from the tub.
UNIVERSAL MOTOR Firstly, you have to do from 1 to 5 of HEATER AND THERMISTOR DISASSEMBLY. 1 Separate the box inlet as from the washer. (Remove screws and hose inlet) 2 Remove the screw of the motor connector. And separate the connector from the tub. 3 Separate the hose air from the sensor pressure. 4 Lay the front-side of washer on the floor. And remove four screws. 5 Separate two dampers and the hose drain. 6 Lift up the cabinet as. 7 Separate the belt.
5. EXPLODE VIEW AND PARTS LIST ■ BOX INLET AS No. PART NAME SPECIFICATION Q'TY REMARK A01 CASE HANDLE 36111T2T00 HIPS, D-MT 1 A02 CASE DETERGENT 36111T2V00 PP, D-MT 1 A03 BOX INLET 3617511700 PP 1 A04 CAP SOFTENER 3610907800 PP 1 A05 NOZZLE TOP 3618112000 PP 1 A06 NOZZLE UNDER 3618112100 PP 1 A07 HOSE WATER SUPPLY 3613270900 EPDM ID9.5 OD14.5 2(3) A08 CLAMP HOSE 3611205800 100H, ID=13.8 W=10.0 0.
■ PANEL FRONT AS No.
■ CABINET FRONT AS No. 14 PART NAME PART CODE SPECIFICATION Q'TY C01 CABINET F 361081280T SECD T0.7 1 C02 NUR HEX 7S627W50X1 NUT FLANGE M5x0.8P MFZN 2 C03 SWITCH DOOR LOCK 3619047100 DL-LC BITRON-3P 250V16A 1 C04 SCREW TAPPING 3616029950 TTS " S" HEX F/L 4x8 5 C05 SCREW TAPPING 7122401408 T2S TRS 4x14 SUS 2 C06 CLAMP DOOR AS 3611204810 HSW3, D1.
■ TUB AS EXPLODE VIEW AND PARTS LIST 15
No. PART NAME PART CODE SPECIFICATION Q'TY D01 TUB REAR AS 3618830911 D-MT'S TUB REAR+BEARING HOUSING C/CORE 1 D02 BEARING INNER 3616304700 6205ZZ SHENS 1 D03 BEARING OUTER 3616304800 6204ZZ SHENS 1 D04 WATER SEAL 361A600300 NBR 1 D05 GASKET TUB 3612324100 PI=4.
■ CABINET AS EXPLODE VIEW AND PARTS LIST 17
No. PART NAME PART CODE SPECIFICATION 361081WA00 D-MU80 SGCC(GI) 0.7T COLD 361081WA01 D-MU80 SGCC 0.7T COLD+HOT E02 FRAME LOWER 36122UDR00 SGCC T=0.6 1 E03 BASE U L 3610394500 SGCC1.2T 1 LEFT BASE U R 3610394600 SGCC1.2T 1 RIGHT E04 LEG ADJUST AS 3617703800 FOOT(BUTYL)+SPECIAL NUT(SCP1) 4 E01 CABINET Q'TY REMARK 1 COLD COLD+HOT +SPECIAL BOLT(10x1.
6. FUNCTIONS OF THE CONTROL PANEL ■ D-M805'S/M105'S Program selector Indicator light For switching the washing machine on and off and for selecting the program. Can be rotated in both direction. Even if the program selector rotates while the program is running, the program is not changed (except for off ). (All program is electronically controlled by PCB) The respective indicator lights up, when the required program segment runs or ‘Time delay’ is selected. Time delay To pre-engage time for washing.
7. FUNCTIONS OF THE CONTROLLER ■ SEQUENCE CHART (DWD-M805'S/M105'S) Cotton Division P R E W A S H Progress Time Sensing Water Supply Pre Wash Drain B-Spin Middle Spin Sensing Water Supply Wash 1 (Heating) W A S H Wash 2 R I N S E S P I N END Drain B-Spin Middle Spin Water Supply Rinse 1 Drain B-Spin Middle Spin Water Supply Rinse 2 Drain B-Spin Middle Spin Water Supply Rinse 3 Drain B-Spin Main Spin Untangle End Total Time NOTE 20 20sec. 2min. 10min. 8min. 1min. 2min. 3min. 20sec. 2min. 70min.
Division P R E W A S H W A S H R I N S E S P I N END Progress Time Sensing Water Supply Pre Wash 20sec. 2min. 10.min. 8min. 1min. 2min. 3min. 20sec. 2min. 50min. 25min. 20min. 15min. 10min. 33min. 28min. 23min. 20min. 18min. 13min. 1min. 2min. 4min. 2min. 3min. 1min. 2min. 4min. 2min. 3min. 1min. 2min. 4min. 2min. 3min. 1min. 2min. 7min. 5min. 3min. 1min. 10sec.
8. FUNCTION OF THE CONVENIENT SERVICE ■ The test mode of the load movement You can check the PCB ASS'Y and the condition of each load movement simply. • The method to test the load movement 1 Plug the power cord. 2 Turn the program selector to arbitrary program (except for OFF position). (The indicator light of the Start/Hold button is on but not twinkles. If the indicator is twinkles, press the Start/Hold button and turn the program selector to the off.
9. TROUBLESHOOTING GUIDE This washer is equipped with automatic safety function which detects and diagnoses faults at an early stage and copes properly. When the washer does not operate properly, check the following points. ■ Simply Check Guide Problem Cause Program dose not start. Plug is loose or not plugged in. Water dose not enter the washing machine. Washing machine is not drain. Washing machine is not spin. Solution Insert plug tightly. Power failure.
■ DISPLAY ERROR MESSAGE MESSAGE IE OE UE LE 24 ERROR WATER INLET ERROR DRAIN ERROR UNBALANCE ERROR DOOR OPEN ERROR TROUBLESHOOTING GUIDE CAUSE SOLUTION The water tap is closed. Open the water tap. The filter of the valve inlet is clogged. Clean the filter of the valve inlet. The valve inlet is an inferior product or broke down. Change the valve inlet. The water level sensor (sensor pressure) is an inferior product or broke down. Change the water level sensor (sensor pressure).
MESSAGE ERROR E2 OVERFLOW ERROR CAUSE SOLUTION The water is supplied continuously due to an inferior valve inlet. Change the valve inlet. The valve inlet is normal, but the water level sensor (sensor pressure) is inferior. Change the water level sensor (sensor pressure). The drain motor dose not work. (The drain motor is an inferior product or broke down.) Change the drain motor. E4 LEAKAGE ERROR Water leaks from the tub or the hose drain. Check the leak of the tub or the hose drain.
12 WH 12 12 BL SENSOR THERMISTOR BUBBLE PUMP (OPTION) PRESSURE 123 Vdd1 BK GY OR RD PK YW GND Signal PRE COLD RD BL YW WH VT VALVE INLET PUMP MOTOR SWITCH DOOR LOCK BK PK HOT (OPTION) 132 WF-2 12345678 12345678 YL R (OPTION) EARTH OUTER MOTOR MAIN (UNIVERSIAL) T 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 WF-3 4321 4321 WH PK GN BL RING 2 1 RY-8 RY1-HO (OPTION) (1800W) RING RY8-HI RING WF-5 123456 123456 HEATER WASH GN/YW RD BR RING WF-1 21 21 12 R.
DAEWOO ELECTRONICS CORP. 1-2, Jeo-dong 1(il)-ga, Jung-gu, Seoul, Korea C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” S/M NO. : PRINTED DATE: Feb.
ABOUT THIS MANUAL VISION CREATIVE, INC. 서울 종로구 통의동 6번지 이룸빌딩 4층 담 당 MODEL 정재열 님 DWD-M8051/M8052/M8053 DWD-M1051/M1052/M1053 (S/M) 접 수 2007.06.01 총 31페이지 MEMO 총 28p 11.02.21-전체 신규 28p 11.03.18-19p, 20p 수정_ 신규 2p 11.03.22-2p, 15p, 16p 수정_ 신규 3p 11.05.06-20p, 21p 수정_ 신규 2p 11.05.23-표지 (DWD-M1051/M1052/M1053 추가), 2p, 12p, 13p, 14p, 15p, 16p, 17p, 18p, 19p, 20p 수정_ 신규 11p 11.05.
