S/M No. : TSC110NEF0 Service Manual Relese 1 DIGITAL HDTV CHASSIS : SC-110 Model : DSC-30W60N DSC-30W60N Specifications General Picture Sound Number of Inputs / Outputs R-V3 Power Requirement Power Consumption Dimensions(W/H/D) AC 120V, 60Hz 250W (1.
TABLE OF CONTENTS 1. Product Safety ................................................................................................................................2 2. Specifications .................................................................................................................................4 3. Reote Control Overview.................................................................................................................5 4. Limited Warranty .....................................
1.PRODUCT SAFETY SERVICING GUIDELINES FOR COLOR TELEVISION RECEIVERS GRAPHIC SYMBOLS : CAUTION : Do not attempt to modify this product in any way. Unauthorized modifications will not only void the warranty, but may lead to your being liable for any resulting property damage or user injury. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines. To do otherwise, increases the risk of potential hazards and injury to the user.
SUBJECT : IMPLOSION 4. Wall and shelf mounted installations using a commercial mounting kit, must follow the factory approved mounting instructions. A receiver mounted to a shelf or platform must retain its original feet(or the equivalent thickness in spacers) to provide adequate are flow across the bottom, bolts or screws used for fasteners must not touch and parts or wiring. Perform leakage test on customized installations. 5.
2. Specification General Power Requirement Power Consumption Dimensions(W/H/D) Weight Antenna RF Band Coverage AC 120V, 60Hz 250W (1.
33. Remote control overview The remote control has the following functions: 1. Power button Press to turn the HDTV(and other equipment) on and off. 2. MODE buttons Press to select which equipment you wish your remote control to operate: * SAT(satelite) * CATV (cable box) * VCR * TV The Mode button you press will light up in red. 3. MENU button Press once to display the HDTV menus. Press again to make the menus disappear. 4. SEL ( Select) button Press to select items on the HDTV menus. 5.
Remote control overview 11. SOUND button 24. PREV (Previous) button Press to select a sound option : Mono, Stereo, or Secondary Press to back up one menu at a time in the HDRV menus or to Audio Programming (SAP). When you tune to a digital return to the previous channel. channel, press to select various languages. 12. SLEEP TIMER button Press to select the time before the HDRV turns off: 30 minutes, 60 minutes, 90 minutes, or 120 minutes. 13. CLOSED CAPTION button Press to turn closed captions on and off.
4. Limited Warranty Daewoo Electronics Corporation of America Inc. (also known as DECA) warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers 3 years labor and 3 years parts from the date of original purchase. This warranty applies only to product purchased from authorized DECA dealer and used within the boundaries of U.S.A.
5. Service Modes 1. Entering to Service Mode 1) With the user remote control Press the button in the following order. 1 MUTE SELECT MUTE POWER 2) With the service remote control S1 : Heat Run S2 : Screen Voltage S3 : Sound Controls S4 : Video Controls S5 : Geometry S7 : White Balance S8 : Sub Brightness S9 : Software Version S10: Factory Setting 2. Function of each service mode 1) S1 : Heat Run mode.
Service Modes 5) S5 : Geometry Adjustment mode V Size Max 31 Side Pin W 22 V Size 0 Side Pin S 34 V Position 26 Trapezoid 33 V C Linearity 23 Side Pin Balance 31 V S Linearity 31 H Duty 31 H Size 53 Parallelogram 28 H Position 70 H Focus Phase 31 Pincusion 32 H Focus Amplitude 60 6) S6 : No Use 7) S7 : White Balance Adjustment mode White Balance Control Drive R Bias R 128 64 G 32 G 224 B 128 B Initial value 64 8) S8 : Sub Brightness Adjustment mode.
Service Modes 3. Selecting the adjusting items 1) With the user remote control Pressing of ARROW s button changes the adjustment items. (t button for reverse order) 2) With the service remote control Pressing of CHANNEL s button changes the adjustment items. (t button for reverse order) 4. Adjusting the data 1) With the user remote control Pressing of ARROW3button changes the value of data.4 ( button for reverse order) 2) With the service remote control Pressing of VOLUME3button changes the value of data.
6. General Adjustment In the majority of cases, a high definition digital television will need basic adjustments such as high voltage, screen voltage, focus, white balance, sub brightness, geometry, and blanking width. All adjustments should be performed after heat-running the set for at least 20 minutes. 1. Press the S1 button on the service remote control, and then full white pattern will appear on the screen. 2. Press again the S1 button, and then the pattern will disappear. High Voltage Adjustment 1.
General Adjustment 4. Dark Area Adjustment 1) On the center of dark area, attach the sensor of a white balance meter. 2) To be Y=12, turn the Dark Beam control volume on the White & Black pattern generator. 3) To adjust the white balance of dark area, select Bias R, G, B with CHANNEL Up or Down buttons, and adjust individual values with VOLUME Up or Down buttons. 4) Repeat two processes above until the white balance is completed. Sub Brightness Adjustment 1. Tune on Retma Pattern. 2. Press S8 button. 3.
General Adjustment Geometry 1. To adjust V-Position, H-Size, H-Position and so forth, tune on Retma Pattern. 2. To adjust Pincushion, Parallelogram and so forth, tune on Cross Hatch signal. 3. Screen Mode should be on Full mode, and the Video Mode should be on Normal mode. 4. Press S5 button to adjust Geometry. 5. With Up/Down buttons, perform the adjustment items in the following order. Item Screen Image V Size Max. Adjustment Procedure 1) Receive NTSC Retma signal.
General Adjustment Item VS Linearity Horizontal Size Horizontal Position Pincushion Side Pin W Screen Image Adjustment Procedure 1) Receive NTSC Retma signal. 2) The Screen mode should be selected on Full mode 3) When the center area of Retma signal’s circle is S type in the vertical direction, adjust VS Linearity so that vertical interval may be the same. 1) Receive NTSC Retma signal.
General Adjustment Item Screen Image Adjustment Procedure 1) Receive NTSC Cross Hatch signal. 2) The Screen mode should be selected on Full mode. 3) When the vertical lines of the left and right side is not straight but distorted in the S type, adjust Side Pin S to correct the unbalanced vertical lines. Side Pin S 1) Receive NTSC Cross Hatch signal. 2) The Screen mode should be selected on Full mode.
General Adjustment Item Screen Image Adjustment Procedure 400Vp-p H Focus Amplitude 1) There is no need to adjust, and check if the value of data is "32". 2) Check if the focus on the right and left side is clear. 900Vp-p 60Hz Blanking Width 1. Tune on NTS Retma pattern. 2. Press Screen mode on the remote control, and then slelct Normal mode. 3. To be symmetrical the screen, adjust Blanking Width with rotating the variable volume RU19 on the Blanking Board.
7. Special Adjustment (When replacing new circuit boards) 1. DTV Decoder module 1) Before replacing a new module, if seeing OSD menu is possible, record the adjusted data value of White Balance and Geometry. 2) After replacing the defective module with a new one, memorize the value of data value to the new DTV decoder module with the service remote control. 3) Perform the Y Level Adjustment. 2.
8. Troubleshooting charts. No Picture (NTSC Signal) NO OSD is on the screen. To DTV Decoder Module AV Signal RF Signal Check video signal of IC210. CVBS is to pin 13 of PW01M Video 1 : CVBS to pins 43 ,Y to pin 45, NO and C to pin 47 Video 2 : CVBS to pin 7 Check Tuner (U101). YES Video 3 : CVBS to pin 27 Video 4 : CVBS to pin 1 ,Y to pin 3, and C to pin 5 NO YES NO CVBS is to pin 34 of IC210. Check each input signal. Check IC210. YES NO Check if CVBS is 1Vp-p to pin 88 of ICA1.
Troubleshooting charts V1 NO To DTV Decoder Module When input signal is color bar, check the following output level to PA06D. Y=0.7Vp-p ± 0.1Vp-p Pb=0.6Vp-p ±0.1Vp-p Pr=0.6Vp-p±0.1Vp-p YES Check the input and output signal of IC208. Pins 9, 10, and 11 : Low (Base of QC215 : High) Pin 14 : Y signal Check IC208 NO Pin 15 : Pb signal Check logical state to pin 52 of IC 212.
Troubleshooting charts V2 NO Signals R, G, and B are to pins 2, 4, and 6 of PW07K. Check the following parts. R : pin 25 of IC201, Q218 YES G : pin31 of IC201, Q216 B : pin 28 of IC201, Q217 There are R signal to R504, G signal to R513, and B signal. NO Check the following parts. 130Vp-p ±10Vp-p R: pin8 of IC501, G: pin8 of IC502, B: pin 8 of IC503 Check 200V and 12V of PA17M.
Troubleshooting charts Y, Pb, Pr Input NO OSD is on the screen. To DTV Decoder module YES Check the SELECT SGINAL switch on the rear panel is to Y/Pb/Pr. NO If the switch is selected to R/G/B, the color of screen is pale green. Select the switch to Y/Pb/Pr. Check if Y/Pb/Pr signals are well connected to input terminals. YES Check if pin 18 of IC212 is Low. Check the input/output signal of IC207. Pins 9, 10, and 11 : Low Pin 14 : Y signal Pin 15 : Pb signal Pin 4 NO : Pr signal Check IC207.
Troubleshooting charts R, G, B Input NO OSD is on the screen. To DTV Decoder module YES NO Check the SELECT SGINAL switch on the rear panel is to R/G/B. Select the switch to R/G/B. YES NO Signals R, G, and B are to pins 7, 8, and 9 of IC201. Check IC207. YES NO Signals B-Y, Y and R-Y are to pins 3, 4, and 5 of IC201. Check IC207. YES Check the input/output signal of IC207. NO Check IC207.
Troubleshooting charts No sound (NTSC) Audio signal output is only R and L. There are no sound to Center, SL, SR, and Woofer. RF Signal AV Signal Check if the audio signals are input to the follow Check the audio base-band signal to SIF of U101. pins of IC210 (CXA1855). Amplitude of SIF : 800mVp-p ± 100mVp-p Video 1 : L to pin 44, R to pin 46 YES Video 2 : L to pin 8, R to pin 10 Video 3 : L to pin 25, R to pin 26 Video 4 : L to pin 2, R to pin 4 SIF is to pin 67 of IC215.
Troubleshooting charts A1 NO Check if R, L signals are input and output to I609. (The audio output of I609 is equalized signal.) Audio L input : pin 1, Audio R input : pin 30 Audio L output : pin 12, Audio R output : pin 19 YES Check if R, L signals are input and output to I607.
Troubleshooting charts No sound (External HD) SL, SL, Center, and Woofer R, L Check the following audio signals. Check if R, L signals are input and output to IC215. SL input / output : pins 12, 6 of I603 HD_L input : pin 53 HD_L output : pin 37 SR input / output : pins 16, 2 of I603 HD_R input : pin 54, HD_R output : pin 36 NO C input /output : pins 9, 7 of I602 YES NO W input /output : pins 9, 7 of I603 Decoder Check I603 YES Check IC215. R, L and I602.
Troubleshooting charts NO Sound Decoder (RF DTV) C, W, SR, SL R, L Woofer, Center, SR, SL Check DEC_R and DEC_L to PA05D. Check S_R, S_L, Center and Woofer to PA12D. NO To DTV Decoder module Decoder R, L Check the following audio signals.
Troubleshooting charts H/V Sync Check (External HD Component Input) R/G/B/Hs/Vs R/G/B with sync on green or Y/Pb/Pr Check the input/output signal of IC202. Check the input/output signal of IC203 Pins 11, 10 : High (Base of QC215 : Low) G or Y input : pin 4 HS input : pin 13 HS output : pin 14 HS output : pin 14 VS input : pin 1 VS output : pin 15 VS output : pin 13 NO YES NO Check IC202. S2 Check IC202. YES Check the input/output signal of IC203.
Troubleshooting charts S1 Check the following signals. NO HP : pin 6 of PW01V Check HP signal of Q426’s base. 5Vp-p NO Check VP signal of Q415’s base. 33.75KHz VP : pin 7 of PW01V 5Vp-p YES Check VP signal is to pin 21 of IC212. 60Hz NO YES YES Check IC204. Check HP signal is to pin 13 of IC216 through IC204. NO Check EVEN/ODD signal is to pin 46 of IC 212 Check IC204 YES YES NO Check IC212. Check HP signal is to pin 14 of IC216 . Check EVEN/ODD signal is to pin 1 of IC216.
Troubleshooting charts H/V Sync Check (RF DTV, RF NTSC, AV NTSC) DEC_HS is to PA06D. NO 3.3Vp-p To DTV Decoder module 33.75KHz DEC_VS is to PA06D. 3.3Vp-p 60Hz YES DEC_HS is input / output to pins 15, 2 of IC209. NO Check IC 209. DEC_VS is input / output to pins 14, 13 of IC209. Pins 10, 11 of IC 202 : High (Base of QC215 : High) YES DEC_HS is input to pin 12 of IC 202. NO DEC_VS is input to pin 2 of IC 202. Check IC 202. H_sync is output to pin 14 of IC 202.
Troubleshooting charts No Raster NO Press POWER button, and wait for 2 minutes. Check if TV micro- processor (IC212) communicates Power LED keeps continuously lighting up green. with DTV Decoder module on UART. If the LED changes from green to red, check pin 39 YES (TXD) of IC212. IC212 communicates with I402 on the IIC bus. 5Vp-p Check the pins 3 (SDA) and 4 (SCL) of I402. Check the pin 38 (RXD) of IC212 or pin 6 of PA05D. 5Vp-p 3.3Vp-p NO YES Check IC212 and I402.
Troubleshooting charts HD1 NO Trigger pulse is input to pin 2 of I407. Check Q416, Q417 2Vp-p 6Vp-p 33.75KHz YES The control voltage of H Drive is input to pin 5 of I407. NO 60Hz Check pin 9 (E/W ) of IC402. 0.5Vp-p 7Vp-p YES NO H Drive signal is output to pin 3 of I407. Check I407. 12Vp-p 33.
Troubleshooting charts HD2 NO Check 200VA to PA14M. To No Power YES NO H Drive signal is output to Source of Q423. Check Q423. 200Vp-p 33.75KHz YES Horizontal Drive B+ to R481 is about 130Vp-p ±10Vp-p . 60Hz 10Vp-p 130Vp-p YES The voltage waveform of Q425’s collector is the following. NO 1400Vp-p ±50Vp-p If the impedance value of Q425’s collector is near zero Ω , the horizontal deflection TR (Q425) is dead. Replace Q425.
Troubleshooting charts High Voltage Drive Check pin 17 (H-Drive output) of I402. NO 0.7Vp-p Check I402. 33.75KHz YES Check H Drive signal to emitter of Q402. 12Vp-p 33.75KHz NO Trigger pulse is input to pin 2 of I401. NO Check Q403. 2Vp-p 6Vp-p 33.75KHz YES The control voltage of high voltage feedback is input to NO Check I403 and high voltage pin 5 of I401. feedback circuits. 60Hz 0.
Troubleshooting charts HVD1 High Voltage Drive signal is output to pin 3 of I401. NO Check I401. 12Vp-p 33.75KHz YES NO Check 200VB to PA14M. To No Power YES High Voltage Drive signal is output to Source of Q407. NO Check Q407. 200Vp-p 33.75KHz YES FBT B+ to pin 15 of PW16P is about 130Vp-p ±10Vp-p. NO 60Hz Check Q407.
Troubleshooting charts HVD2 Check EHT Drive signal to base of Q808. NO Check emitter of Q401. 12Vp-p 33.75KHz YES The voltage waveform of Q810’s drain is the following. NO Check Q810.
Troubleshooting charts Vertical Deflection NO Check I402. Vertical SAW waveform is to pin 8 of I402. 2.2Vp-p 60Hz YES The following waveform is to pin 1 of I412. NO Check vertical deflection circuits around I412. 3.5Vp-p 0V YES Vertical deflection waveform is to pin 5 of I412. NO 50Vp-p 60Hz END 36 Check vertical deflection circuits around I412.
Troubleshooting charts No Power (Standby Power : U801) The Standby LED doesn’t light up red. YES NO Approximately 150VDC is to C806. Check if F801 is open. Check D801 (bridge rectifier). YES The following waveform is to drain of U801. NO Check the impedance value of between Source and Drain to U801. If the value is near zero Ω, U801 is dead. Replace U801. 320Vp-p 100KHz YES Check if voltages to PA17D is supplied to DTV NO Check the parts caused a short-circuit to secondary circuits.
Troubleshooting charts No Power Switch relay (Y802) doesn’t operate. YES (F801) doesn’t short-circuit. Replace F801. NO NO Bridge rectifier (D805) doesn’t short-circuits. Replace D805. (The voltage of between Anode and Cathode to D805 is 0.6V). YES NO Both AC lines of power cord don’t short-circuit. Replace the parts caused a short-circuit. YES NO PWR SW to PW15M is High. Check pin 26 of IC212. YES NO Q804 doesn’t defective. Replace Q804. YES NO Check Y802(switch relay). ReplaceY802.
Troubleshooting charts P1 The following waveform is to pin 1 of U803 and U805. NO Check the primary circuits of SMPS IC, and replace defective parts with a new one. 370Vp-p 50~80KHz END NO Power Switch relay operation (Y802) is OK. Check the parts caused a shortcircuit to secondary circuits.. NO Replace defective parts with a new one. YES NO Supply the power to PA17D. NO S/B SW to PW15 is High. YES P2 P3 39 Check pin 13 of IC212.
Troubleshooting charts P2 P3 Check Regulators. YES (U807, U808, U809) NO Supply 200VA to PA14M. NO R803 is OK. ReplaceR803. YES NO R815 is OK. Replace R815. YES NO Q802, D815 are OK. YES Replace Q802, D815. YES Check U805. NO Supply 200VB to PA14M. NO R807 is OK. Replace R807. YES NO Q801, D810 are OK. YES YES Check U803. END 40 Replace Q801, D810.
Troubleshooting charts DTV Channel Trouble When NO Signal Searching is not display Select Input Select on the Setup Menu, and Check Check Signal Strength. Check tuner power to pins 6, 11, and 15 of U101. NO Check IF signal to pin 19 of U101. 123, 124, 125 of IC100. Change Tuner U101. NO YES Check TS stream signal to pins 122, YES Check AGC to pin 3 of U101. NO Check B+, Clock and IIC Bus to pins 94, 104, and 105 of IC100. YES Check Please Back-end A/V function.
Troubleshooting charts No Picture to DTV RF (Color and luminance signal is not output.) Check Y, Pb, and Pr to pins 38, 33, and 39 of IC917(Video DAC). NO Check Pixcko to pin 27 of IC917. Check 27MHz clock to pin 88 of IC901(Video decoder), and Y/Pb/Pr to pin 93 ~ 125. YES V1 NO V2 If no signal, change IC901. END Mosaic Picture to DTV RF Mosaic picture is displayed on the screen. Check 97MHz clock to pin 68 of IC902 and IC903.
Troubleshooting charts Loss of H/V sync to DTV RF Picture is scrolling due to horizontal or vertical sync loses. Check H/V sync signal of Video decoder to PW06V. Check 27MHz clock to pin 88 of IC901(Video decoder), and Y/Pb/Pr to pin 93 ~ 125. NO Check H/V sync. If no signal, change IC901. YES To H/V Sync Check END (RF DTV, RF NTSC, AV NTSC) No sound to DTV RF (Audio L, R) NO Check audio L/R to pins 2, 4 of PW05V Check pins 21, 22 of IC920 (Codec IC).
Troubleshooting charts No sound to DTV RF (Audio Center, Woofer) NO Check audio C/W to pins 2, 4 of PW12M. Check pins 23, 24 of IC920. YES NO Check pins 63, 64, 67, and 73 of IC912. Decoder YES NO C, W, SR, SL Check pins 188, 190, and 197 of IC701 (Transport IC). NO END If no signal, change IC701. No sound to DTV RF (Audio SL, SR) NO Check audio C/W to pins 6, 8 of PW12M. Check pins 25, 26 of IC920. YES NO Check pins 63, 64, 67, and 73 of IC912.
✔ Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 9.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE Q425A 4857027534 I412 1TDA8172-- IC V-OUT TDA8172 I412A 4857028207 HEAT SINK AL EX BK Q425B I412B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN Q425C I413 1KA7809--- IC REGULATOR KA7809 R476 I414 1KA7805--- IC REGULATOR KA7805 ! I601 1CXA1315P- IC CONVERTER CXA1315 ! I602 1LA7220--- IC SWITCH LA7220 R I603 1LA7220--- IC SWITCH I605 1UPC1406HA IC I606 1UPC1406HA IC UPC 1406HA I6
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS CC612 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CC613 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 RC404 HRFT102JCA R CHIP 1/10 1K OHM J 2012 CC614 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 RC405 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 CC615 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 RC406 HRFT682JCA R CHIP 1/10 6.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS RC465 HRFT102JCA R CHIP 1/10 1K OHM J 2012 RC467 HRFT103JCA R CHIP 1/10 10K OHM J 2012 RC656 HRFT393JCA R CHIP 1/10 39K OHM J 2012 RC468 HRFT102JCA R CHIP 1/10 1K OHM J 2012 RC657 HRFT393JCA R CHIP 1/10 39K OHM J 2012 RC469 HRFT102JCA R CHIP 1/10 1K OHM J 2012 RC658 HRFT303JCA R CHIP 1/10 30K OHM J 2012 RC470 HRFT103JCA R CHIP 1/10 10K OHM J 2012 RC659 HRFT333JCA R CHIP 1/10 33K OHM J 2012 RC471 HRF
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION E27 4856310300 EYE LET BSR T0.2 (R1.6) C401 CCXB1H391K C CERA 50V B 390PF K (TAPPING) E28 4856310300 EYE LET BSR T0.2 (R1.6) C402 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP E29 4856310300 EYE LET BSR T0.2 (R1.6) C403 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP E30 4856310300 EYE LET BSR T0.2 (R1.6) C404 CEXF1C221V C ELECTRO 16V RSS 220MF (8X11.
Part List (DSC-30W60N) LOC C485 PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION REMARKS CMXB2A103J C MYLAR 100V EU 0.01MF J (TP) Q421 TKTC3202Y- TR KTC3202Y (TP) C486 CEXF2A479V C ELECTRO 100V RSS 4.7MF (5X11) TP Q422 TKTA1270Y- TR KTA1270Y (TP) C487 CMXM2A473J C MYLAR 100V 0.047MF J (TP) Q424 TKTC3198Y- TR KTC3198Y C490 CMXL2E104K C MYLAR 250V MEU 0.1MF K Q426 TKTC3198Y- TR KTC3198Y C491 CMXL2E104K C MYLAR 250V MEU 0.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION D443 D1N4148--- DIODE 1N4148 (TAPPING) R438 RD-AZ332J- R CARBON FILM 1/6 3.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION R613 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R623 RD-AZ182J- R CARBON FILM R626 RD-AZ273J- R CARBON FILM R629 RD-AZ471J- R630 R632 REMARKS LOC PART CODE PART NAME DESCRIPTION JU3 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING 1/6 1.8K OHM J JU4 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING 1/6 27K OHM J RU1 RD-AZ472J- R CARBON FILM 1/6 4.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION PA07V 4950706009 CONNECTOR SMH250-06+YT250+USW=350 PA08V 4950703007 CONNECTOR PA10V 4950704007 CONNECTOR PA11V 4950706008 PA17M PA18M REMARKS LOC PART CODE PART NAME DESCRIPTION C518 CMXL2E104K C MYLAR SMH250-03+YT250+ULW=500 C519 CCXB2H561K C CERA 500V B 560PF K (TAPPING) SMH250-04+YT250+ULW=800 C521 CXCH1H121J C CERA 50V CH 120PF J (TAPPING) CONNECTOR SMH250-06+YT250+ULW=450 C522 CCXF1H103Z C CERA 50V F 0.
Part List (DSC-30W60N) LOC D509 PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION DRH1B----- DIODE RH-1B (TAPPING) R533 RD-AZ390J- R CARBON FILM 1/6 39 OHM J D510 DRH1B----- DIODE RH-1B (TAPPING) R534 RD-AZ561J- R CARBON FILM 1/6 560 OHM J JY1 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING R535 RD-AZ109J- R CARBON FILM 1/6 1 OHM J JY2 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING R536 RD-AZ222J- R CARBON FILM 1/6 2.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION C890 CCYE3D103P C CERA 2KV E 0.01MF P C891 CCYE3D103P C CERA 2KV E 0.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC C835 CEXF1C102C C ELECTRO 16V RUS 1000MF (10X20) TP C807 C843 CEXF1C102C C ELECTRO 16V RUS 1000MF (10X20) TP C845 CEXF1C102C C ELECTRO 16V RUS 1000MF (10X20) TP C848 CEXF1C471V C ELECTRO C850 CCXB3D221K C852 CEXF2C220V C853 PART CODE PART NAME DESCRIPTION CMXB1H104J C MYLAR 50V EU 0.
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION C901 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP L804 5MC0000100 COIL BEAD HC-3550 F801A 4857415001 CLIP FUSE PFC5000-0702 L805 5MC0000100 COIL BEAD HC-3550 F801B 4857415001 CLIP FUSE PFC5000-0702 L806 5MC0000100 COIL BEAD HC-3550 L811 58C0000096 COIL CHOKE 610G0233(470K) L807 5MC0000100 COIL BEAD HC-3550 L813 58C0000096 COIL CHOKE 610G0233(470K) L808 5MC00001
Part List (DSC-30W60N) LOC PART CODE PART NAME DESCRIPTION REMARKS LOC PART CODE PART NAME DESCRIPTION REMARKS R859 RD-4Z103J- R CARBON FILM 1/4 10K OHM J R888 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R860 RD-4Z103J- R CARBON FILM 1/4 10K OHM J R891 RD-2Z103J- R CARBON FILM 1/2 10K OHM J R861 RD-2Z472J- R CARBON FILM 1/2 4.
10. Circuit Diagram 10-1.
Circuit Diagram 10-2. Signal Flow Diagram CRT ASS'Y R G B VM YPbPr VIDEO ASS`Y ATSC ASS'Y MAIN L/R VIDEO AUDIO NTSC A/V MAIN L/R MAIN L/R C SL SR WOOFER SPEAKER HD L/R SIF C.
Circuit Diagram 10-3.
Circuit Diagram 10-4.
Circuit Diagram 10-5.
Circuit Diagram 10-6.
Circuit Diagram 10-7.
Circuit Diagram 10-8.
Circuit Diagram 10-9.
Circuit Diagram 10-10.
Circuit Diagram 10-11.
Circuit Diagram 10-12.
11.
Circuit Diagram 10-13.
