！ Us ebol t st os ecur et hef r amet ot hegr oundt oagai ns tt hes t r ongwi nd.
1 Pole Beam Beam Corner Roof Bar Corner Roof Bar Connector Roof Bar Corner Roof Solidifying Bar Corner Roof Solidifying Bar Corner Roof Solidifying Bar Corner Roof Solidifying Bar Finishing Bar Finishing Bar Finishing Bar Finishing Bar Finishing Bar Solidfying Bar
Solidfying Bar Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Plastic Bar Base Joint Cover Inside Roof Connector 2 Bracket Union Bar Outside Roof Connector Bracket Corner Solidifying Bar Joint Cover Corner Solidifying Bar J-Hook Bracket Hook Bracket
Bracket 3 Bracket Joint Cover Corner Cover Spacer Finishing End Solid Sidewall Mosquito Sidewall Mesh Joint Cover Finishing End
(1) Attach 2 Part #B1 to Part #A with 4 Bolts #8. (2) Attach 2 Part #B2 to Part #A with 4 Bolts #6. 4 (3) Attach Part #B to Part #A with 3 Bolts #8. (4) Repeat the above procedures to assemble the other three Part #A.
(1) Insert Part #X into Part #C1. (3) Insert the other side of Part #C2 into Part #C1 and secure with 4 Bolts #8. (2) Insert one side of Part #C2 into Part #C and secure with 4 Bolts #8. X4 32 (4) Secure Part #X with 2 Bolts #3. 5 (5) Repeat the above procedures to assemble the other three sides.
(1) Connect Part #C and #C1 to Part #A with 4 Bolts #4 and 4 Bolts #5 (From Outside). (2) Repeat the above procedures to assemble the other three sides. Please don’t tighten all the bolts.
(1) Connect Part #C and #C1 to Part #A with 4 Bolts #8. (From Inside) (2) Repeat the above procedures to assemble the other three sides. C 7 C1 Please don’t tighten all the bolts.
(1) Affix Part #R and #R1 to the frame with 8 Bolts #8. (2) Repeat the above procedures to assemble the other three sides. C1 C1 8 Please don’t tighten all the bolts.
(1) Cover the corner with Part #X1 and secure with 2 Bolts #2. (2) Put Part #X2 on the protruding place and secure with 2 Bolts #3. (3) Repeat the above procedures to assemble the other three sides. 9 Tighten all the bolts.
Assemble the 4 Corner Roof Bars: 8 10
(1) Please have a freestanding ladder ready at the center of the gazebo. (2) Place 4 Part #E1 on Part #S; secure with 8 Bolts #8 (from bottom to top). ATTENTION: You can also finish this step on the ground and then lift 4 Corner Roof Bar and Inside Roof Connector to the top together. (Need 2 people and 2 ladders) U 11 (3) Place 4 Part #E on 4 Part #A; secure with 8 Bolts #8.
(1) Place Part #E2 on Part #S; secure with 2 Bolts #8( from bottom to top). C C1 12 (2) Connect Part #E2 and the Assembled Beam (C&C1) with Part #U1. Secure with 3 Bolts #8. (3) Repeat the above procedures to assemble the other three side.
(1)Attach Part #U2 to Part #F/F1/F2/F3 with Bolt #6. (2)Repeat the above procedures to assemble the other 3 pieces.
(1) Insert Part #F2 and Part #F3 into Corner Roof Bar Part #E; secure with 2 Bolts #6. (2) Insert Part #F and Part #F1 into Corner Roof Bar Part #E; secure with 2 Bolts #6. F/F2 F1/F3 W1 F1/F3 14 F/F2 (3) Connect Part #F/F1/F2/F3 and the Assembled Beam with Part #U2; secure with Bolt #8. (4) Repeat the above procedures to assemble the other three sides.
(1)Insert Part #W3 to Part #K1 and secure with Bolt #8. X4 w E2 F2 E2 F3 F2 F3 12 1 F2/F3 K/K1 2x (2) Attach Part #K and Part #K1 with Part #W3 and 2 Bolts #8. 15 (3) Connect Part #K (K1) and Part #F2 (F3) with Bolt #9. (4) Repeat the above procedures to assemble the other three sides.
(1) Insert Part #W2 into Part #K1 and Part #K. (2) Secure them to Part #E with 3 Bolts #8. 16 (3) Repeat the above procedures to assemble the other three sides.
Secure Part #T to Part #Z2, Part #S and Part #S1. ATTENTION: The holes of Part #Z2, Part #S and Part #S1 need to be aligned, on the same vertical line.
Insert Part #Q1 into the hole that around the edge of Part #Z2.
4 4 (1) Place Part #J, Part #J1 and Part #Q1 into order on Part #E2; put on Part #Y and secure with Bolt #8. ATTENTION: The holes need to be aligned. (2) Repeat the above procedures to assemble the other three sides.
(1) Attach Part #Q1 on Part #J&J1 with 2 Bolts and Nuts #7. (2) Place Part #Y1 on Part #J/J1 and Part #E, securing with Bolt #8. (3) Repeat the above procedures to assemble the other three sides.
ASSAMBLE ROOF PANELS: P2 P2 P2 P2 21
(1) Insert Part #P2 into the top roof. (2) Place Part #H2 on Part #E2, securing with Bolt #8. E2 E2 E2 E2 (3) Repeat the above procedures to assemble the other three sides.
E1 (1) Place Part #H2 on Part #E1; put on Part #Y1 and secure with Bolt #8. (2) Repeat the above procedures to assemble the other three sides.
(1) Insert Part #L, Part #L1 and Part #L2 into the frame. L2 E2 8 F F2 E2 F F2 F/F2 (2) Attach Part #G to the frame, securing with 2 Bolts #6. (3) Repeat the above procedures to assemble the other three sides.
(1) Insert Part #N, Part #N1 and Part #N2 into the frame; F3 L F1 L E2 8 E2 F3 F1 (2) Attach Part #G1 to the frame, securing with 2 Bolts #6. (3) Repeat the above procedures to assemble the other three sides.
(1) Place Part #G and Part #G1 on Corner Roof Tube Part #E2; put on Part #Y and secure with Bolt #8. (2) Repeat the above procedures to assemble the other three sides.
E G1 G (1) Place Part #G and Part #G1 on Part #E; put on Part #Y1 and secure with Bolt #8 (2) Repeat the above procedures to assemble the other three sides.
(1) Place 7 hooks on each slot of the Sidewall Track (C&C1). 4X C C1 C1 C C C1 C C1 Double-Track (2) Install Part #W at the joint of Part #C&C1 with Bolt #8. 28 (3) Repeat the above procedures to assemble the other three sides.
Hang up mosquito sidewalls to inside track.
Hang up solid sidewalls to outside track.
