All-in-one Bullet Network Camera Quick Start Guide V1.0.
Quick Start Guide Foreword General This manual introduces the functions, installation and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. Indicates a potential risk which, if not avoided, could result in property damage, data loss, lower performance, or unpredictable result.
Quick Start Guide errors in the print. If there is any doubt or dispute, we reserve the right of final explanation. Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if any problems occur while using the device.
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation should conform to your local electrical safety codes. The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2. Note that the power supply requirements are subject to the device label. Make sure the power supply is correct before operating the device. A readily accessible disconnect device shall be incorporated in the building installation wiring.
Quick Start Guide during installation or operation. For removing dust, grease or fingerprints, wipe gently with moistened oil-free cotton with diethyl or moistened soft cloth. You can also remove dust with an air blower. WARNING Please strengthen the protection of network, device data and personal information by adopting measures which include but not limited to using strong password, changing password regularly, upgrading firmware to the latest version, and isolating computer network.
Quick Start Guide Table of Contents Foreword ............................................................................................................................................................ I Important Safeguards and Warnings ............................................................................................................... I 1 Introduction.................................................................................................................................................
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ manual. Figure 1-1 Cables Table 1-1 Cable information No. Port name Description Inputs 12 VDC power. Be sure to supply power as instructed in the manual. 1 Power input 2 Ethernet port 3 Alarm I/O 4 RS-485 5 Audio input Device abnormity or damage might occur if power is not supplied correctly.
Quick Start Guide Port Port Name Description ALARM_COM Outputs alarm signal to alarm device. ALARM_ON When connecting to alarm device, only the ALARM_COM port and ALARM_ON port with the same number can be used together. 1.2 Connecting Alarm Input / Output The camera can connect to external alarm input/output device through digital input/output. Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port.
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the ConfigTool or on web page. For more information, see web operation manual. Device initialization is available on select models, and it is required at first-time use and after device is being reset. Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stays in the same network segment.
Quick Start Guide When initializing multiple devices, ConfigTool initializes all devices based on the password reset mode of the first selected device. Figure 2-2 Password setting Step 8 Set and confirm the password of the devices, then enter a valid email address, and then click Next. Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected. Step 10 Click OK to initialize the device.
Quick Start Guide 2.2 Changing Device IP Address You can change IP address of one or multiple devices at one time. This section is based on changing IP addresses in batches. Changing IP addresses in batches is available only when the corresponding devices have the same login password. Step 1 Follow Step1 to Step4 in "2.1 Initializing Device" to search devices in your network segment.
Quick Start Guide 3 Installation 3.1 Packing List The tool required for the installation such as electric drill is not provided in the package. The operation manual and related tool information are contained in the disk or the QR code. Figure 3-1 Packing list 3.
Quick Start Guide 3.3 Installing Camera 3.3.1 Installation Method Figure 3-3 Installation method 3.3.2 Installing SD/SIM Card Disconnect the power before installing or removing the SD/SIM card. Micro SIM card size: 15 mm × 12 mm × 0.76 mm （L × W × H). Press the reset button for 10 seconds to reset the device.
Quick Start Guide 3.3.3 Attaching Camera Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket. Figure 3-5 Attach camera 3.3.4 Installing Waterproof Connector (Optional) This part is needed only when there is waterproof connector in the package and the device is used outdoors.
Quick Start Guide 3.3.
Quick Start Guide
