Dahua HD Pinhole Network Camera Quick Start Guide Dahua HD Pinhole Network Camera Quick Start Guide Version 1.0.0 Dahua Vision Technology Co., Ltd.
Dahua HD Pinhole Network Camera Quick Start Guide Welcome Thank you for purchasing our network cameras. This user’s manual is designed to be a reference tool for your system. Please read the following safeguards and warnings carefully before you use this series product. Please keep this user’s manual well for future reference. Important Safeguards and Warnings 1.Electrical safety All installation and operation should conform to your local electrical safety codes.
Dahua HD Pinhole Network Camera Quick Start Guide Do not dismantle the device as there is no component that can be fixed by users themselves in the device. Otherwise, it might cause water leakage or bad image for the device due to unprofessional dismantling. Please contact after-sale service to replace desiccant if it becomes green. It is recommended to use the device with lightning arrester to improve thunder-struck protection effect.
Dahua HD Pinhole Network Camera Quick Start Guide FCC Information 1. FCC conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. 2. FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
Dahua HD Pinhole Network Camera Quick Start Guide Table of Contents 1 Device Framework .............................................................................................................................. 1 1.1 1.2 1.3 2 3 Structure and Dimension ...................................................................................................... 1 1.1.1 Structure and Dimension of Modular Pinhole Network Camera ................................... 1 1.1.
Dahua HD Pinhole Network Camera Quick Start Guide 1 Device Framework 1.1 Structure and Dimension Note: The framework figures in this manual are just for reference. There might be some minor differences between the actual products and the corresponding figures, so please refer to the actual products you purchased. 1.1.1 Structure and Dimension of Modular Pinhole Network Camera 1.1.1.1 Structure You can refer to the following figures for port information. See 错误!未找到引用源。 and Figure 1-2.
Dahua HD Pinhole Network Camera Quick Start Guide Table 1-1 Description of Port Function SN Port Port Name Audio output Connector Function Note Output audio signal to the speakers and other devices. 1 AUDIO OUT 2 AUDIO IN 3 Micro SD Card Micro SD Micro SD Card slot Micro SD card storage 4 SENSOR Sensor port Sensor board Connect front end Sensor board, get image data.
Dahua HD Pinhole Network Camera Quick Start Guide 1.1.1.2 Dimension Please refer to the following figures for dimension information of different models for modular pinhole camera. The unit is mm. Please refer to Figure 1-3 for the dimension of model A. Figure 1-3 Dimension of model A Please refer to Figure 1-4 for the dimension of model B.
Dahua HD Pinhole Network Camera Quick Start Guide Figure 1-6 Dimension of rear end Please refer to Figure 1-6 for the dimension of rear end for the three models described above. 1.1.2 Structure and dimension of All-in-one Pinhole Network Camera You can refer to the following figures for more details. See Figure 1-7.
Dahua HD Pinhole Network Camera Quick Start Guide Figure 1-8 Structure of device Please refer to the table 1-3 for more details about each component. Table 1-3 Description of components No. Name Function 1 Lens Receive the optical signal from the environment. 2 Back cover - 3 Binding wire It is used to fix the cable. 4 Network port Connect to standard Ethernet cable. 5 Power input port Power port, input DC 12V。 6 Bracket It is used to fix the camera.
Dahua HD Pinhole Network Camera Quick Start Guide Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the bidirectional talk function. Click Talk button again to stop the bidirectional talk function.
Dahua HD Pinhole Network Camera Quick Start Guide 2. Connect alarm output device to the alarm output port of I/O cable, alarm output port can only be connected to NO alarm device. 3. Open the Web, set alarm input and output correspondingly. Alarm input 01 on WEB corresponds to the first alarm input of I/O cable on device. When there is alarm, alarm input device will generate signal of high and low level. Set corresponding NO and NC inputs. 4. Set the WEB alarm output.
Dahua HD Pinhole Network Camera Quick Start Guide 2 Device Installation Note: All the installation figures below are for reference only due to the different models and appearances; please refer to the actual devices for exact details. 2.1 Installation of HD Modular Pinhole Network Camera This product is a kind of separate device, and both the front end and the rear end of the device have to be installed respectively.
Dahua HD Pinhole Network Camera Quick Start Guide Figure 2-2 Installation of round front end 1. Take out the installation bracket from the accessories bag (with installation foam) 2. Tear off the film of the foam, and stick it on the surface to be installed. 3. Set the fixing ring on the installation bracket. 4. Put the round front end into the installation bracket and adjust the location. 5. Tighten the fixing ring.
Dahua HD Pinhole Network Camera Quick Start Guide Refer to the following installation steps: 1. Open the accessories bag and take out the fixing enclosure (with fixing foam). 2. Stick the fixing enclosure on the installation surface. 3. Embed the square front end into the fixing enclosure. Installation Mode 2: Figure 2-4 Installation mode 2 for square front end Refer to the following installation steps: 1. Dig the holes for installation expansion bolts on the installation surface. 2.
Dahua HD Pinhole Network Camera Quick Start Guide Figure 2-5 Installation of device Install the camera: Use screws to fix the camera on the installation wall, as it is shown in Figure 2-1. Location /angle adjustment: 1. Install the camera on the fixed wall together with the bracket. The screw is installed in the middle hole, and then the camera can rotate. The screw is installed in the left and right waist-shaped holes, and then the camera can be adjusted rightward and leftward. 2.
Dahua HD Pinhole Network Camera Quick Start Guide 3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108). To make the camera get access to the network smoothly, please plan the useable IP segment reasonably according to the actual network environment. 3.
Dahua HD Pinhole Network Camera Quick Start Guide 4. Modify the camera IP address on the “Net” interface, click “Save” to finish modification. See Figure 3-2 for more details. Figure 3-2 Network parameters 3.2 Login WEB Interface Note: Different devices may have different WEB interfaces, the figures below are just for reference, please refer to the document WEB Operation Manual in the disk and the actual interface for more details 1. Open IE and input the modified camera IP address in the address bar.
Dahua HD Pinhole Network Camera Quick Start Guide 2. The login interface is shown below, please input your user name and password (Default user name is admin and password is admin respectively), click “login”. 3. Install controls according to the system prompt. See Figure 3-4 for the WEB main interface. Please modify the administrator password as soon as possible after you successfully logged in. Figure 3-4 WEB main screen Note: This quick start guide is for reference only.