Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Version 1.0.1 Zhejiang Dahua Vision Technology Co., Ltd.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Welcome Thank you for purchasing our network cameras. This user’s manual is designed to be a reference tool for your system. Please read the following safeguards and warnings carefully before you use this series product. Please keep this user’s manual well for future reference. Important Safeguards and Warnings 1. Electrical safety All installation and operation should conform to your local electrical safety codes.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide dismantling. Please contact after-sale service to replace desiccant if it becomes green. It is recommended to use the device with lightning arrester to improve thunder-struck protection effect. The grounding holes of the device are recommended to be grounded to further enhance the reliability of the device. Do not touch the CCD (CMOS) optic component directly.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide This device must accept any interference received, including interference that may cause undesired operation. 2. FCC compliance： This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Table of Contents 1 Device Framework .............................................................................................................................. 1 1.1 Device External Cable .......................................................................................................... 1 1.2 Dimension ..........................................................................................................................
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 1 Device Framework 1.1 Device External Cable Note The following structure figure is for reference only. It is only used to know the functions of device ports. There might be some minor differences between different devices, so please refer to the actual products you purchased. The following figure shows port information.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide The following tables show more information about port function. Table 1-1 Cable port function No. Cable port Port name Connector Function description Power port, input DC12V or AC24V. Note 1 POWER Power input port - 2 It needs to connect the default DC5.5 round port to 2-pin converter cable when you are using AC 24V power. Actual use in accordance with device label instruction.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Figure 1-2 Device dimension (unit: mm) 1.3 Alarm Setup Note This function is only supported by some models. The following figure shows the Alarm setup screen. Figure 1-3 Alarm setup To set up the Alarm input and output, do the following: 1. Connect alarm input device to the alarm input port of I/O port cable. 2. Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND ports of I/O port cable.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 4. Set alarm output on the WEB, the alarm output is corresponding to the alarm output of the device, that is, the alarm output port of the I/O port cable. The following figure shows Alarm input. Figure 1-4 Alarm input Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the alarm input port. The input signal is connected to 3.3V or it is idle, the device collects the logic “1”.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 2 Device Installation Note Wall-mounted dome can be installed on the hard wall structure in both indoor and outdoor environments. The bracket installation wall shall be thick enough to install expansion bolts and make sure it can sustain at least 8X weight of the total weight of bracket and camera. Please cut off the device power before installing Micro SD card.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 3. Insert the SD card into the card slot shown in Figure 2-2. Press it gently until it locks into place. Note You can check video via connecting the analog video output port to the TV monitor. Long press the reset button for 4 to 5 seconds to realize the reset the device. Step 2 Fix the device on the installation surface. To install the device, firstly take out the necessary accessories, and then do the following: 1.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide are of the same type, you can find in the accessory bag. Figure 2-5 Fixing adapter and steel cable 5. Connect the hook of steel cable to the hanging ring of adapter, and fix the nut of the hook. Then align the top buckle of the changeover plate with the internal holes of the adapter, finally tighten the fixing screw of adapter firmly. See Figure 2-6.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide box from the wall, then put them together into the junction box. Use 4 fixing screws to fix the wall-mount bracket on the junction box. See Figure 2-7. Figure 2-7 Device and junction box connection Step 3 Adjust the monitoring direction of the device. See Figure 2-8. Note The range of angle adjustment for lens: horizontal rotation direction (0︒~ +355︒), vertical rotation direction (0︒~ +75︒), and image rotation direction (-20︒~ +20︒).
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide Step 4 (Optional) Waterproof connector installation for network port. See Figure 2-9. Note Implement this step if the device is equipped with network port waterproof connector and it is used outdoors. Figure 2-9 Waterproof Connector Installation for Network Port 1. 2. 3. 4.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP 192.168.1.108). To make the camera access to the network smoothly, please plan the available IP segment reasonably according to the actual network environment. 3.1 Modify IP Address The cameras which are accessed via wired network can acquire and modify the IP address through “Quick Configuration Tool”.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide See Figure 3-2 for more details. Figure 3-2 Network Parameters 3.2 Login WEB Interface Note Different devices might have different WEB interfaces, the figures in this document are just for reference, please refer to the document WEB Operation Manual in the disk and the actual interface for more details. To login WEB interface, do the following: 1.
Dahua HD Panoramic Multi-sensor Network Dome Camera Quick Start Guide 3. respectively), click Login. Note The default username and password is admin and admin respectively, please modify the administrator password as soon as possible after you successfully logged in. Install controls according to the system prompt. See Figure 3-4 for the WEB main interface. Figure 3-4 WEB main interface Note This quick start guide is for reference only. Minor differences might be found in user interface.
