Use and Care Manual

www.daichcoatings.com • 1-866-GO-DAICH (463-2424)
Textured Primer locks
into concrete pores
and also creates
added surface profi le
for enhanced bond of
subsequent coatings.
DAICH Textured Primer
acts as the exposed
visible “grout joint”
in DAICH stenciled
fl oor coating projects.
Creates the realistic
appearance of tile and
stone fl oor coverings.
TEXTURED PRIMER
Textured
Primer
SURFACE PREPARATION:
For optimal long–term performance, surface should be clean and dry – and free from dust, dirt, spalling, efflorescence, oil, poorly bonded or glossy paint, glue,
surface sealers and other contaminates. New concrete – minimum 28 day cure before application. New masonry – 48 - 72 hours cure before coating.
CONCRETE / MASONRY / BRICK:
1) Surface should be level and in good condition. Chip away any loose or flaking concrete and skim coat any rough or uneven areas with a quality levelling
compound. Allow to cure as directed. 2) If concrete is smooth, new or efflorescent, the surface must be etched using Daich Concrete Cleaner/Etcher as directed,
or a two-parts water / one-part muriatic acid solution (consult muriatic acid container for mixing and safety instructions). For very smooth
concrete, etching twice is advisable. If concrete is heavily soiled, cleaning is required prior to etching to ensure best results. After etching,
follow with general cleaning. 3) Whenever possible, clean concrete with a pressure washer. For best results, especially for exterior
surfaces, a minimum of 2000 psi is recommended in a slow sweeping motion. Hold spray fan tip 4” above the concrete to effectively clean
out pores for best bond.) If a pressure washer is not available, scrub the surface with Daich Concrete Cleaner/Etcher or a strong TSP
solution. Rinse thoroughly, removing all washing/etching debris with clean water and a scrub broom followed by thorough rinse. 4) To
prepare exterior brick and concrete block surfaces, pressure wash as normal to remove accumulated dirt and grime. Allow to dry fully before
coating. 5) For interior walls, wash and /or wipe down prior to application to the dry surface. It drywall dust is present, vacuum dust and
wipe down with a damp cloth before proceeding.
MIXING: Daich Textured Primer is pre-mixed and ready to apply. Stir before use.
APPLICATION
1) Application temperature range - 50ºF - 80ºF. 2) Apply by paint roller until the surface is thoroughly and uniformly coated. 3) Brush or roll carefully into all surface
texture, light pitting, etc. for full contact over the entire surface. Coated surface must be uniformly covered without show-through. 4) For broom finished concrete,
brush uniformly into and in the same direction as the broom texture for full contact. Let dry 20-30 minutes and follow with a roller-applied coat (same direction as
the broom texture) to fill the broom texture completely. 5) Two coats are recommended for projects utilizing a DAICH decorative stencil or grout line effect.
APPLICATION TOOLS: Use a 3/8” roller for level unpitted concrete. For textured surfaces, use a 1/2” pile roller for better penetration. Paint brush for edges and
deeper texture spot filling.
DRY & CURE TIMES: Outdoor dry (>70º F) 30 - 60 minutes (longer in damp or cool conditions). Indoor dry (>70º F) 1 - 2 hours (due to limited air flow).
Full cure: 24 hours.
COVERAGE: Average of 160 sq.ft. (15m2) per gallon (18.9 liters) based on one uniform coat over a smooth surface. Varies with roughness of surface and
application technique.
STORAGE: Textured Primer may be stored in its original unopened container in a cool dry place for up to two years.
PRECAUTIONS:
Avoid contact with eyes and skin, flood eyes repeatedly with potable water for 15 minutes. DO NOT RUB EYES due to stone content of material. Wash hands
thoroughly after handling. Do not take internally. KEEP OUT OF REACH OF CHILDREN. Keep container closed. Dispose of old material as prescribed by local
laws.
Need further assistance or have questions? Call - 1-866-463-2424. Or email us at [e-mail].