OPERATION MANUAL Wireless remote controller kit BRC7E530W8 BRC7E531W8
1 ON/OFF ON/OFF 8 1 H 3 M L TEMP H DOWN 10 11 C M L TIME C UP 6 4 FAN FAN 9 hr. 2 UP 2 ON OFF RESERVE CANCEL 13 hr. 12 hr. DOWN TIME TIMER CODE MODE UNIT NO. •4•6 hr. 15 SWING 14 5 7 TEST TEST 16 5•7 TEST 17 1 1 2 3 4 20 21 22 23 19 18 24 25 3 4 6 7 5 1 CODE 2 2 1 5 3 6 7 UNIT NO.
BRC7E530W8 BRC7E531W8 Wireless remote controller kit CONTENTS Page Safety considerations .....................................................1 Names and functions of the operating section ...............2 Handling for wireless remote controller ..........................3 Precautions in handling remote controller .................... 3 Installation site.............................................................. 3 Placing the remote controller in the remote controller holder..........................
NAMES AND FUNCTIONS OF THE OPERATING SECTION See figure 1, (figure 1B shows the remote controller with font cover opened) 16 FILTER SIGN RESET BUTTON Refer to the section of MAINTENANCE in the operation manual attached to the indoor unit. 17 INSPECTION/TEST OPERATION BUTTON This button is used only by qualified service persons for maintenance purposes. 1 DISPLAY “ ” (SIGNAL TRANSMISSION) This lights up when a signal is being transmitted.
HANDLING FOR WIRELESS REMOTE CONTROLLER Placing the remote controller in the remote controller holder Precautions in handling remote controller Install the remote controller holder to a wall or a pillar with the attached screw. Make sure the remote controller transmits. ■ Direct the transmitting part of the remote controller to the receiving part of the air conditioner.
OPERATION RANGE ■ Refer to the operation manual provided with the indoor unit or with the outdoor unit. ■ If the indoor temperature or humidity is beyond operating conditions as listed in the indoor unit or outdoor unit manuals, it may happen - that safety devices work, - that the air conditioner does not operate, - that water drips from the indoor unit. ■ The setting temperature range of the remote controller is 16°C to 32°C. ON/OFF Press ON/OFF button.
Explanation of heating operation Defrost operation FAN SPEED CONTROL ■ As the frost on the coil of an outdoor unit increase, heating effect decreases and the system goes into DEFROST OPERATION. ■ The fan operation stops and the DEFROST lamp of the indoor unit goes on. After 6 to 8 minutes (maximum 10 minutes) of DEFROST OPERATION, the system returns to HEATING OPERATION. Heating capacity and outdoor air temperature ■ Heating capacity drops as outdoor air temperature lowers.
Program timer operation 4 Operate in the following order. ■ The timer is operated in the following two ways: - Programming the stop time ( ). The system stops operating after the set time has elapsed. - Programming the start time ( ). The system starts operating after the set time has elapsed. ■ The timer can be programmed for a maximum of 72 hours. ■ The start and the stop time can be simultaneously programmed. 1 TIMER CANCEL Press the TIMER OFF button to cancel programming. The display vanishes.
How to designate controller the master remote Operate in the following order. 1 Continuously press the OPERATION SELECTOR button for 4 seconds. MODE The displays showing “ ” of all slave indoor units connected to the same outdoor unit or BS unit flash. 2 Press the OPERATION MODE SELECTOR button to the indoor unit that you wish to designate as the master remote controller. Then designation is completed.
HOW TO DIAGNOSE TROUBLE SPOTS In case besides emergency stop 1 The unit does not operate at all. ■ Check if the receiver is exposed of sunlight or strong light. Keep receiver away from light. ■ Check if there are batteries in the remote controller. Place the batteries. ■ Check if the indoor unit number and wireless remote controller number are equal. See figure 6. Operate the indoor unit with the remote controller of the same number.
NOTES
Zandvoordestraat 300, B-8400 Oostende, Belgium 4PW23711-1