Installation Instructions

ManualsBrandsDaikin ManualsAir Conditioner AccessoriesWired Remote Control

Wireless LAN Connection Adapter Installation Procedure

The following procedures are also applicable to air

conditioners ﬁtted with an S21 connector.

All types

When turning on the power, always

attach the upper adapter case.

Top clip of lower

case

•

Attach it to the reverse side of the lower case.

•

Depending on the type of the wall, there is a

possibility of damaging the wall, and the

adapter falling.

Please install it after consulting with the client.

Do not

fasten the

screws

into the

indoor unit.

Do not block the

holes at the top

and bottom.

Mounting screws

When attaching the fastening tape

Fastening tape

Fasten the connection

cord and ensure that

external force is not

transmitted.

Lower

case

Slot-head screwdriver

Upper

case

Do not press the

screwdriver into

the hole for the

connection cord.

Connector

Cord anchor

Ensure that the connector on

the connection cord is

ﬁrmly inserted all the way.

Wireless LAN connection adapter

4. Return the adapter case to its

original condition.

Close the adapter by hooking the top of the

upper case on the top clip of the lower case.

Push until you hear a click.

Check that the

connection cord is

securely fastened.

1. Remove the upper case of the

wireless LAN connection adapter.

Press a slot-head screwdriver* into the dent between the

upper and lower cases of the wireless LAN connection

adapter to remove. (Be careful not to damage the case.)

* Use a slot-head screwdriver with a wide head (0.2 inches

(5mm) or wider is recommended).

5. Turn on the power supply, wait until the

initialization is complete, and check that

the [POWER] lamp of the wireless

LAN connection adapter lights up.

2. Attach the connection cord to the

wireless LAN connection adapter.

1) Attach the connector of the connection cord.

2) Fasten the connection cord to the notch in the lower

case of the wireless LAN connection adapter.

3. Install the lower case of the wireless

LAN connection adapter to a wall, a

pillar, or similar location.

• Install the lower case so as to allow the upper case to be

easily removed for maintenance purposes.

• Do not install outdoors or anywhere it is likely to get wet.

• Do not install it near the sensor part of the indoor unit.

All types

[MODE]

button

[WPS] button

Preparation Before Conﬁguring Connection Settings

Conﬁguring Connection Settings (1)

The customer is responsible for providing the following.

• Smartphone or tablet PC

(Supported OS: Android 4.0.3 or later; iOS 7.0 or later.)

• Internet line and communicating device

(Modem/router or a similar device)

• Wireless LAN access point

(The corresponding channel for the wireless LAN connection adapter is 1-11.)

• [DAIKIN Mobile Controller] (No Cost)

Check that the [POWER] lamp is continuously lit and the [RUN] lamp

is blinking.

• If the [POWER] lamp is lit and the [RUN] lamp is not lit, hold down the [MODE] button on the

adapter for about 2 seconds to prompt the [RUN] lamp to begin blinking. (Blinking begins in

about 30 seconds.)

2. Press the [WPS] button on the router (wireless LAN access point).

• Operation procedures for the [WPS] button vary by router (wireless LAN access point).

For details, refer to the instruction manual for the router.

Hold down the [SETUP] button on the adapter for about 2 seconds.

• The [RUN] lamp will begin to blink more rapidly, and will change to a continuous light once a

connection between the router (wireless LAN access point) and the adapter has been

established.

If a connection fails to establish, repeat procedures from step 1 of “Simple setup”.

If a connection still cannot be established, follow the procedures in “Advanced setup”.

(In some cases, a connection cannot be established using the steps in “Simple setup” owing

to compatibility issues.)

4. Connect the smartphone (tablet PC) and the router (wireless LAN

access point).

• A connection can be established by opening the smartphone's Wi-Fi network list, selecting

the [SSID] for the router and entering its password.

5. Tap the installed app [Daikin Comfort Control] to start it.

• If the connected air conditioner is listed in the units overview screen, setup is complete.

If it is not listed, tap (refresh) in the top right corner of the units overview screen.

Installation method of online controller

(1) Open the [App Store].

(2) Search for [Daikin Comfort Control].

(3) Follow the directions on the screen to install.

(1) Open the [Google Play].

(2) Search for [Daikin Comfort Control].

(3) Follow the directions on the screen to install.

For Android Phones/Tablets For iPhones/iPads

Simple setup

Note

• If an upgrade is available for your adapter, the notiﬁcation icon “ ” will be displayed on the

units overview screen. Tap it to upgrade your ﬁrmware.

• If an upgrade is available for your adapter, the notiﬁcation icon “ ” will be displayed on the

Check whether the router to be used supports WPS.

Proceed to

If WPS is supported

Simple setup

Proceed to

If WPS is not supported

Advanced setup

Conﬁguring Connection Settings (2)

All types

(2) Select your home

network from the

list.

(1) Tap [Conﬁgure

the wireless

connection].

(4) Follow the on-screen instructions from here onward to complete setup.

(5) After implementing the setting above and the product and router (wireless LAN access point) are connected, the [RUN] lamp will light.

If this blinks for 1 minute or longer, check the power to the router (wireless LAN access point), network name and the password and start

again from the ﬁrst procedure.

[MODE]

button

(3)

Enter the password.

Tap [Connect].

To set the wireless connection manually, tap [Advanced network settings], turn off

[Automatic IP address (DHCP)], ﬁll in the required information for the Wi-Fi router, tap [ ]

and then tap [Connect] on the wireless connection screen. Follow the on-screen instructions

and then continue as in step (5).

for the Wi-Fi router, tap [ ]

1. Check that the [AP] lamp is lit (continuously).

If the [AP] lamp is not lit, hold down the [MODE] button on the adapter

for about 2 seconds to prompt the [AP] lamp to light up (continuously).

(Lights in about 10 seconds.)

5. Connect the smartphone (tablet PC) and the router (wireless LAN access point), and

then start [Daikin Comfort Control].

• Refer to step 4 and step 5 of “Simple setup”.

2. Connect the smartphone (tablet PC) directly with the adapter via wireless LAN.

• Open the smartphone's Wi-Fi network list, select the [SSID] (DaikinAP *****) shown on the serial number sticker, or the

wireless LAN connection adapter, and then enter the [KEY].

3. Tap the installed app [Daikin Comfort Control] to start it.

4. Make the wireless connection settings.

Advanced setup

• All steps are demonstrated using iOS.

Troubleshooting

After-sale Service

The following table provides brief descriptions of how to handle problems or uncertainties when you install the product or make

connection settings. Check our website for details.

When this happens Explanation and where to check

[RUN] lamp does not light up

(continuously).

The [RUN] lamp blinks.

 Perform Simple setup or Advanced setup again.

 Check that the [SSID] and password for the adapter are entered correctly.

 Move the router (wireless LAN access point) closer to the adapter.

 The smartphone or router (wireless LAN access point) in use may not be supported.

Check our website for details.

3P427537-1A

For inquiries concerning after-sale service, contact your dealer and advise them of the following details:

• Model name

• Date of installation

• Conditions at the time of failure (as precisely as possible)

• Your address, name, and telephone number

URL

http://daikincomfort.com/DuctlessWireless/FAQ

• FAQ can be viewed via smartphone

(tablet PC). To access, please scan

the 2D barcode.

This telecommunication equipment is in compliance with FCC/IC requirements.

FCC CAUTION

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This device complies with Part 15 of FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of this device.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio

frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be

installed and operated keeping the radiator at least 8 inches (20cm) or more away from person’s body.

Contains FCC ID:VPYLBYD

Contains IC: 772C-LBYD

01_EN_3P427537-1A.indd 2 2/22/2016 3:07:09 PM