ORBIT MASSAGE LOUNGER ORB-2 / ORB-3 Consumer Limited Warranty: ONE-YEAR WARRANTY This warranty guarantees that the product purchased is to be free from defects in material and workmanship under normal usage and local voltage for a period of one year. This warranty expires in TWO (2) years on parts, and ONE {1) year on labor after the date of purchase. U.S. Clean, Inc.
}> TECHNICAL SPECIFICATIONS ) ORBIT Product name: Orbit Massage Lounger Product Model: ORB-2 / ORB-3 Rated voltage: 110-120 V~ Rated frequency: 60 Hz Rated power: 1.1 A 30, Thank you for purchasing the Orbit Massage Lounger. Before using this chair for the first time, please read through all sections of this User Manual carefully, paying special attention to the Safety Instructions. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
J» IMPORTANT SAFETY PRECAUTIONS » Basic precautions should always be followed when using an electrical unit, including the following. » Please ensure that you read all instructions before using the Orbit. A DANGER To reduce the risk of electric shack: 1. Always unplug this unit from the electrical outlet immediately after using and before cleaning. A WARNING To reduce the risk of burns, fire, electric shock, or injury to persons: .
> PRODUCT STORAGE AND MAINTENANCE CLEANING » Before cleaning, switch off power and remove the power plug from the wall outlet. » Dip a soft, cotton cloth in neutral detergent and wring dry. Use it to wipe the pillow cushion, back cushion, armrests, footrests, and any plastic parts of the chair. » Use a piece of wet cloth (without detergent) to re-wipe the pillow cushion and back cushion. Place them in a well-ventilated location for drying.
b> PARTS EXTERIOR PARTS Speaker Pillow Back cover INTERIOR PARTS Massage mechanism Shoulder airbags USB port Back heating pad Arm airbags Calf airbags Footsore roller massage Armrest Caster b SETUP GROUNDING INSTRUCTIONS This product must be grounded in the event of an electrical malfunction. Grounding provides a low resistance path for the electric current to reduce the risk of electric shock. The cord is equipped with a built-in equipment-grounding conductor and a 3-prong grounding plug.
b SETUP b PARTS MASSAGE CHAIR PLACEMENT POWER SUPPLY BOX When looking for a location to place your massage chair, keep following in mind: » The chair takes up significantly more space when stretched out, than when in an upright position. With the chair upright, allow at least 3 inches of open space behind the backrest, and at least 12 inches of space in front of the footrest.
b 2D CONTROLLER p SETUP Note: This is the controller that comes with the Orbit Base Mode! (ORBIT. Additional MOVING THE CHAIR features of the chair are unlocked with the upgraded remote control that comes with the Orbit upgraded mode! (ORB T-3). Instructions for both are included in this manual > Make sure that the backrest is in its highest upright position. » Shut off power and remove the power plug from the wall outlet.
b SETUP INITIAL OPERATION P Make sure there are no objects, people, or pets in the vicinity of the unit. PP Use the controller to lower the backrest to its furthest outstretched position. Raise the footrest to its highest position. Make sure that sufficient open space surrounds the chair on all sides. Make sure that the leg rest is properly connected to the main part of the chair. » Return the chair to its original, upright position A caution P Do not sit on the massage chair while the footrest is rising.
p> 2D OPERATION Backrest Up Button » Press and hold to raise the backrest. Backrest Down Button > Press and hold to lower the backrest. Leg Extend Button » Press and hold to extend the footrest. Leg Retract Button > Press and hold to retract the footrest if your legs need more room DISPLAY SCREEN OPERATION Instructions: Navigate the menus using the Direction Dial. Press Right to go to the next sub-menu of your current selection and press Left to return the previous screen.
b SETUP Installation Method 1: Carefully lift the chair and all of its parts from their packaging. > Remove any protective wrapping and check to make sure that all parts are present. 2: Installing the Footrest p> Lift the footrest and connect it with the coupling shaft by hanging {pay attention to the balance), move the hook to one side of the coupling shaft, then attach the other side.
» 2D OPERATION J GENERAL OPERATION Notes: H ; Home Page i TAPPING OFF 1. Upon making any selections within the Saris Hock Art ads Use the Direction Dial to turn || Le + pon ma y oe the ho : ihc Automatic or Manual Mode menus, after pin ng massage function 10 seconds of inactivity, the display screen will rectum to the home page. 2.
> 3D OPERATION SETTING Settings allow you to change the duration, to set your language, to tum on Bluetooth, and to turn ambient lights on or off. Use the Direction Dial to navigate and set these options. Taproom De TIME Massage duration can be set to 10 mind, 20 mind, or 30 mind. LANGUAGE Access alternate languages for the Controller. BLUETOOTH Turn Bluetooth on or off. 20, » 2D OPERATION ROLLER Foot rollers can be adjusted from speed levels 1-3 or muted off completely.
Note: This is the controller that comes with the upgraded Orbit Mode! (ORB T-3). If you have the based model (ORB T-2), use the instructions for that remote instead } 3D CONTROLLER MANUAL ©10:00 Display screen Power button Point adjustment button Menu button. Auto mode button Direction dial Select button Footrest up Backrest Up Footrest down Backrest Down Extend footrest. Retract footrest button 3D Rollers button button » 3D OPERATION Force Ee Adjust the strength of the 3D rollers from weak to strong, 1-5.
p> 3D OPERATION ROLLER Foot rollers can be adjusted from speed levels 1-3 or turned off completely. ZERO GRAVITY Use the Direction Dial to activate Zero Gravity recline mode select Off to return to the initial position. TAPPING OFF Use tha Direction Dial to turn the Tapping massage function on or off. 3D Massage Use the Direction Dial to choose ona of the three 3D programs: Deep Shiatsu, Breathe, or Revive. 3D OPERATION CONTROLLER OPERATION Power Button P Press to tur on the unit.
3D OPERATION Backrest Up Button » Press and hold to raise the backrest. Backrest Down Button > Press and hold to lower the backrest. Leg Extend Button P Press and hold to extend the footrest. Leg Retract Button P Press and hold to retract the forest if your legs need more room DISPLAY SCREEN OPERATION Instructions: Navigate the menus using the Direction Dial. Press Right to go to the next sub-menu of your current selection and press Left to return the previous screen.