DAKE 10- & 20-Ton Floor/Bench Utility Press INSTRUCTIONAL MANUAL (This is a F-20 model so there may be slight differences) WARNING! Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury. Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 Phone: 800.937.3253 Fax: 800.846.3253 www.dakecorp.com customerservice@dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Table of Contents DAKE Standard Limited Warranty......................................................................................................... 3 Return & Refund Policy ......................................................................................................................... 5 Specifications .................................................................................................................
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com DAKE Standard Limited Warranty Finished Machines Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free from defects in material and workmanship under normal use and service within 1 year (12 months) from the delivery date to the end user.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Warranty Exceptions The following conditions are not applicable to the standard limited warranty: (a) Part installation or machine service was not completed by a certified professional, and is not in accordance with applicable local codes, ordinances, and good trade practices.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Return & Refund Policy Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are here to help. Returns All Dake manufactured / distributed machines, parts and couplings include a 30-day return option. These policies are valid from the date of final shipment to the end user. To be eligible for a return, the item must be unused and in the same condition as received.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SAFEGUARDING THE POINT OF OPERATION ANSI B11.2 – Hydraulic Power Presses Safety Requirements for Construction, Care and Use It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safeguards.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com AMT – The Association for Manufacturing Technology 7901 Westpark Drive Mclean, VA 22102 Specifications Machine Specifications: - 10 Ton Bench 10 Ton Floor 20 Ton Floor Press Type Manual 10-ton Bench Manual 10-ton Floor Manual 20-ton floor Cylinder Type Single Acting Single Acting Single Acting Max.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Safety Warnings BEFORE USE, ALL SAFTEY INSTRUCTIONS MUST BE READ - - - Before the PRESS is used, the instruction manual with this machine must be read and understood. This manual offers safe operation instructions. Offered below are safety instructions designed for the press and general safety instructions that apply to most machinery.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Label Part # 300168 Label Part # 84399 Label Part # 84487 Follow recommended precautions and safe operating practices. Carefully read all safety This machine is intended to messages in these be operated by one person. instructions and on your This person should be press safety signs. Keep conscious of the press ram safety labels in good movement not only for condition.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Assembly Instructions: 10 Ton Bench Model Step 1 (Bench Model Only): - Using (2) M8 x 20mm bolts, nuts and washers install the union support to the bottom from of the upright channels. (Pump hanger bracket on the right-hand side of the upright.) The union support is to face outward. See drawing below. Step 2: - Carefully stand the unit upright.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Step 5: - - Locate the cylinder and remove the plastic protective cap on the end of the ram. (If applicable) Carefully screw the cylinder from the top into the head traverse ram plate. Screw this in as tight as possible while keeping the cylinder’s hydraulic hose fitting facing to the right or pump side.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Assembly Instructions: 10 / 20 Ton Floor Model Step 1: - Install the union support to the inside of the upright channels and base angles, using the 4 of the M8 x 25mm bolts, nuts and washers provided. Step 2: - Place union support in-between the channels and install the 2 base angles to the frame through the union support and install nuts. Base angles face outward (See drawing below) Hand tighten.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Step 5: - Using two 10mm x 120 mm bolts, washers, and nuts, snug only enough to allow plate to travel. Step 6: - Install the pumping device to the mounting plate using 2 M10 x 25mm bolts, nuts, and washers. Make sure pump is aligned in the center on this mounting plate for proper installation. Step 7: - With press standing upright and all bolts tightened install the worktable. Insert two table pins in the two lowest holes.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Operation Procedure - - - Always use the supplied nose pieces. The flat nose piece will be good for most pressing and flattening operations. The step style nose piece will work well for pressing bearing, bushing and parts that have a hole that the nose piece will fit into. This nose piece will help support or hold the piece during pressing operations.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com How to Add Fluid to Hydraulic Pump: 1. Retract the ram that is connected to the pump. 2. Place the pump on a smooth, level surface so that that handle is in the up position. 3. Remove filler plug (small plug near the top). 4. Lift the plug end of the pump 3 8 𝑡𝑡𝑡𝑡 3 4 of an inch off the ground to properly fill the reservoir. 5. Replace the plug to ensure quality sealing. 6. Reinstall pump on press. 7.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Gauge Conversions 10 Ton: 10 Ton 45MM Bore = 1.77 Inch Bore Bar 55 110 165 220 275 551 Tons 1 2 3 4 5 10 PSI(lbs/in2) 799 1598 2397 3196 3996 7992 20 Ton: 20 Ton Tons (1-10) 1 2 3 4 5 6 7 8 9 10 65MM Bore = 2.56 Inch Bore PSI (lbs/in2) Tons (11- 20) 388.86 11 777.73 12 1166.59 13 1555.46 14 1944.32 15 2333.19 16 2722.06 17 3110.92 18 3493.78 19 3888.65 20 #972200, 972210, 972220 16 PSI (lbs/in2) 4277.51 4666.38 5055.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Order Information - - Please contact factory for current prices Parts are available for direct purchase from Dake or through a distributor. When placing a parts order, you will need to provide the part number, name of part, and model number. All parts shipped F.O.B. Factory in Grand Haven, MI.
