User Manual

ManualsBrandsDake ManualsMetalworking & Cutting Tools909205 10-ton Electrically Operated H-frame, 110v-1 ph

Force 10DA & Force 25DA

INSTRUCTIONS AND PARTS

LIST FOR MODEL

FORCE 10DA and FORCE 25DA

(Double Acting, Electrically-Operated Hydraulic Press)

Thank you for buying Dake !!!!

We hope you enjoy many years of using your new Dake hydraulic press. We hope you find these instructions

helpful, if you have any questions please give us a call, or just stop by for a factory tour.

724 Robbins Road

Grand Haven, MI 49417

Phone: 616-842-7110 800-937-3253

Ordering information

Please order all parts by part number and name; also mention model number as shown

on plate attached to the frame of the press.

Note: This press is not intended for stripping operations! Personal injury or

machine damage can result.

Summary of content (14 pages)

PAGE 1
INSTRUCTIONS AND PARTS LIST FOR MODEL FORCE 10DA and FORCE 25DA (Double Acting, Electrically-Operated Hydraulic Press) Thank you for buying Dake !!!! We hope you enjoy many years of using your new Dake hydraulic press. We hope you find these instructions helpful, if you have any questions please give us a call, or just stop by for a factory tour.
PAGE 2
SAFEGUARDING THE POINT OF OPERATION ANSI B11.2 – Hydraulic Power Presses Safety Requirements for Construction, Care and Use It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for a more complete understanding of their responsibilities.
PAGE 3
Press set-up Installation Instructions Your new Dake Press has been packaged in a manner to prevent damage to any critical components; some assembly may be required. All parts in the accessory box are critical to the function of your press. Some presses may come completely assembled. NOTE: FOR EASE OF ASSEMBLY LEAVE THE PRESS FRAME MOUNTED ON THE SHIPPING SKID 1. Remove plastic from the machine. 2. Open the box and you will see a pumping unit, with the press still laying on its side.
PAGE 4
How to install the fittings on your new hydraulic press 1 A Port 1 2 3 4 3 B Port Cylinder 2 5 6 7 8 9 72050 73425 72047 10 ton 301315 25 ton 301316 50 ton 302179 69671 72402 302183 302061 302224 Hydraulic hose connects here and to the A port. 4 Hydraulic hose connects here and to the B port. 5 6 8 7 9 Joy stick valve mounts here. It only fits one way. WARNING!!! Be sure all fittings and bolts are tight. Do not over tighten fittings or bolts.
PAGE 5
Wiring Instructions WARNING!!!! A licensed qualified electrician that follows all state and local laws must wire and install the electrics on this machine. 110 Volt 1. For 110 volts this machine is ready to plug in. The machine can be wired 220 volt single phase. Always follow the wiring diagram provided in the motor cover when converting to 220 volt single phase. A cord and plug that is rated for the specified voltage and amperage must be used. This rating is located on the motor.
PAGE 6
WARNING!!!! This press is not intended for stripping operations! Personal injury or machine damage can result. WARNING!!!! Only use Hydraulic oil in this machine DTE 24 hydraulic oil is recommended. Do not use transmission fluid in this press, the warranty will be void and this fluid will damage the seals.
PAGE 7
PROBLEM & SOLUTIONS Ram moves in the neutral position 4-way valve is off center Ram runs jerky while moving up and down Air in the system Machine will not build desired pressure Relief valve needs to be reset Pins are shearing or bending Relief valve needs to be reset Oil leaks around the ram Cylinder seals need replacing Re-adjust the 4-way valve by centering the valve stem. See Page 5 Self-bleeding system. Continue to run ram up & down aprox. 15 times.
PAGE 8
Force 10DA & Force 25DA 8
PAGE 9
ITEM DESCRIPTION QTY FORCE 10DA FORCE 25DA Part No. Part No. 1 Frame, 10-Ton 1 86517 86684 2 1/2" - 13NC x 2 3/4" 4 43355 43355 3 1/2" Channel Washer 4 43657 43657 4 Workhead Assembly 1 716514 716640 5 1/2" Lock Washer 4 43647 43647 6 1/2" - 13 Hex Nut 4 43916 43916 7 Base Angle 2 85189 978 8 1/2" - 13NC LG. 4 43349 43347 REMARKS LG.
PAGE 10
Force 10DA & Force 25DA 10
PAGE 11
ITEM DESCRIPTION A Piston B Cylinder Flange C Cylinder D Socket Head Cap Screw E O-Ring F Seal G Wear Ring H Wear Ring J O-Ring Complete Workhead Assembly Cylinder Repair Kit (Includes items E, F, G, H, J) Force 10DA & Force 25DA 11 PART NO.
PAGE 12
FORCE 10DA - Specifications Force 10DA & Force 25DA 12
PAGE 13
FORCE 25DA - Specifications Force 10DA & Force 25DA 13
PAGE 14
Safety This is the safety alert symbol; follow recommended precautions and safe operating practices. When you see this symbol on your press be alert to the potential for personal injury. Carefully read all safety messages in these instructions and on your press safety signs. Keep safety labels in good condition. Replace missing or damaged safety labels This machine is intended to be operated by one person.