7/22/03 VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 14-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data is included we cannot fill your order.
7/22/03 Table of Contents Model 14-10 Specifications ………………………………… Page 3 Features ………………………………………. Page 3 Adjustments ………………………………….. Page 4 Lubricating …………………………………… Page 4 Blade Selection ……………………………… Page 5 Parts List ……………………………………..
7/22/03 Specifications Part Number 988050 / 988051 Blade Width ¼-½ inches Blade Length 120 inches Blade Speed 70/140/270/540 Band Wheels 2 Band Wheel Size 14 inches Horsepower 1 h.p.
7/22/03 Adjustments Blade Tension Handle (Item A) – Used to remove and install saw blade. Also used to set the correct blade tension – Be sure blade is tight. Upper Blade Wheel Cant Adjustment (Items B&C) – If your saw should get out of adjustment and the blade runs off the wheel or runs back against the lip, loosen the two bottom bolts on the wheel slide. Turn the set screw in or out to make the blade run approximately 1/32” away from the lip on the back of the wheel. Tighten the two wheel slide bolts.
7/22/03 Blade Selection For Operator convenience, a blade selector chart is located inside the saw cover. It provides recommended blade speeds, required teeth per inch, and minimum cutting radius for various blade widths.
7/22/03 1 2 3 4 5 Item 1 2 3 4a 4b 5 Model 14-10 Part Number 716716 86747 87088 300568 300569 716745 Description Tension Handle Assembly Door Latch Table Door Handle Door Latch Frame Assembly Quantity 1 1 1 2 2 1 6
/22/03 1 2 4 3 2 Item 1 2 3 4 Model 14-10 Part Number 716716 86828 87104 716705 300459 300466 300693 86795 86803 86804 87012 300585 Description Tension Handle Assembly Tension Handle Body Tension Handle Wheel Assembly Band, Blade Wheel Retaining Ring Bearing, Wheel Wheel Blade – Lower/Upper Axle Wheel Lower/Upper Stud – Wheel Blade Guard Speed Selector Label Quantity 1 1 2 2 1 2 2 1 1 1 1 1 7
7/22/03 1 2 3 4 5 6 7 8 10 9 11 12 13 Item 1 2 3 4 5a 5b 6 7a 7b 8a 8b 9 10 11 12 13 Model 14-10 Part Number 43450 86827 86830 43447 86824 86825 86826 43922 43638 43452 43632 43591 86810 300832 70287 43451 Description Cap Screw Pillow Block Tension Screw Cap Screw Wheel Slide – External piece Wheel Slide Adjustment – Internal piece Rail Wheel Slide Nut Washer Soc Cap Screw 3/8-16 x 1-3/4 Washer 5/16” flat Set Screw 3/8-16 x 1 Guide Bar Holder Knob Assembly 1-1/2” Roll pin Cap Screw Quantity 2 1 1 6
7/22/03 13 14 5 4 12 3 2 4 6 1 7 9 10 8 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Model 14-10 Part Number 716749 87081 87025 43939 44033 87078 87077 43449 43451 300564 43939 43591 86806 87034 87033 11 Description Saddle Assembly Table Top Base Table Lock Nut, Hex Jam, 7/16-20 Pin, Dowel Rocker Rings Pointer, Rocker Ring Screw, Soc Set Screw, Soc Cap Cam Follower Nut, Hex Jam 7/16-20 Pin, Spiral or Roll Insert, Contour Guide Insert Lower Guide Holder 1 x 1-5/8” x 1-9/16” Guide Bracket 4” x 4” x ¾” x 1
7/22/03 1 7 2 3 4 6 5 8 Item 1 2 3 4 5 6 7 8 Model 14-10 Part Number 87029 86912 43545 87028 86808 86807 87012 43545 Description Guide Bar Upper guide stem Screw, Soc Cap 1-1/2-6 x 4 1/2 Upper Guide Swivel Holder Contour Insert Insert Contour Guide Blade Guard Screw, Soc Set #10-24 x ¼, Cup point Quantity 1 1 1 1 1 1 1 1 10
7/22/03 7 1 2 3 4 6 5 Item 1 2 3 4 5 6 Model 14-10 Part Number 300473 77449 300522 86798 43314 43632 86800 43450 300597 300542 77449 300485 300486 Description Pulley, Gearbox Key for Pulley V-Belt Motor mounting axle Screw, Hex cap 5/16-18 x 3/4 Washer 5/16 inch flat Block, motor mounting Screw, Soc Cap 3/8-16 x 1-1/4 Screw, Soc Set 1/4 – 20 x 1/4 Pulley, Motor Key for Pulley Motor, Single Phase Motor, Three Phase Quantity 1 1 1 1 2 2 2 4 2 1 1 1 1 11
7/22/03 Model 14-10 12
7/22/03 Item 12 13 14 15 20 21 22 23 28 29 30 31 Model 14-10 Part Number 716712 300472 300490 300491 300589 43412 43414 43590 86820 86821 86822 86823 300666 86784 300456 300646 300454 300448 86785 86781 86783 86786 300449 300451 Description Gearbox Assembly Bearing, Seal Gasket, Gearbox Gasket, Gearbox Dowel Pin 3/16 x 1/2 Screw, Soc Cap Screw, Soc Cap Screw, Soc Set Bearing Cover, Small/hole Bearing Cover, Small Gearbox Casting Cover, Gearbox Gear, Worm 40T Bronze 80 Tooth Gear Worm, 4-Lead 24 Tooth G