Troubleshooting guide

ManualsBrandsDakota Digital ManualsMotorcycle Accessories2000 Series

MAN# 650016

CMD-2000 SERIES REV A

REMOTE UP/DOWN DUAL WINDOW CONTROL

OR LOCK/UNLOCK CONTROL

INTRODUCTION

Thank you for purchasing the CMD-2000 series Remote Window Control from Dakota

Digital, Inc. This, along with many other products that Dakota Digital, Inc. has to offer, represents

the latest in electronics technology for the street rod, classic car and truck, and any custom

vehicle.

The CMD-2000 Remote Window Control system comes complete with receiver, two key

chain transmitters, wiring harness, two dual relay packs, and emergency release switch. An

emergency release switch can be concealed on the underside of the vehicle should the door ever

be closed with the transmitters inside and you on the outside. Pressing this button will allow

reentry to the vehicle.

INSTALLATION

While installation of the CMD-2000 is very straightforward, paying a little attention here and

planning out how the system will fit into your specific vehicle will save some time in the long run.

The receiver should be mounted under the dash up on the fire wall for best access to

wiring. The kick panel is also another good location for the receiver.

Connect the CMD-2000 system as is shown in the wiring diagram. While the wiring

diagram is self explanatory, there are several key areas to pay particular attention to. First, the 12

volt source to the relay packs should be able to supply up to 30 amps. This should have power

whether the key is on or off. The CMD-2000 should only be connected to a 12 volt battery for power

and never solely to a battery charger. The relay packs will typically be mounted inside the doors to

have the fewest wires running through the door jam. The relay packs should be mounted with the

wires exiting the bottom to prevent water from collecting inside the sockets.

ADDITIONAL TRANSMITTERS

The transmitters supplied with your remote system are serial number coded for security.

Each unit can “learn” up to 4 transmitters. It is also possible to program one transmitter into more

than one receiver. If you have more than one vehicle with the CMD-2000 system you can program

all of the transmitters into both units. Transmitters from other manufacturers, such as car alarm

systems, will not work with the CMD-2000.

Summary of content (11 pages)

PAGE 1
CMD-2000 SERIES REV A REMOTE UP/DOWN DUAL WINDOW CONTROL OR LOCK/UNLOCK CONTROL INTRODUCTION Thank you for purchasing the CMD-2000 series Remote Window Control from Dakota Digital, Inc. This, along with many other products that Dakota Digital, Inc. has to offer, represents the latest in electronics technology for the street rod, classic car and truck, and any custom vehicle.
PAGE 2
DAKOTA DIGITAL ANTENNA, DO NOT GROUND not used not used GROUND CH 1 CH 2 in-line FUSE All channels must be connected to relays if they are used. CHANNEL 2 CHANNEL 1 RED: +12 BATTERY BLUE GREEN CHANNEL 3 CHANNEL 4 BLACK: GROUND PINK WHITE YELLOW CHANNEL 7 PURPLE CHANNEL 6 BROWN CHANNEL 5 Wiring harness color code.
PAGE 3
LOCK/UNLOCK OPERATION Each key chain transmitter has four buttons. Each button will activate its own independent channel when pressed. Also, an additional 3 channels can be activated by pressing button 1 and one of the other three buttons at the same time. Button 1 activates the door actuator to lock the doors. Button 3 activates the door actuator to unlock the doors. The door actuator will remain powered for as long as the button is held.
PAGE 4
WIRING DIAGRAMS Wiring a relay for 12 volt accessories Fused 12V power. Do not connect. GREEN 87 BLUE 30 To 12 volt accessory. RED Fused 12V power. WHITE To CMD-2000 channel output. 86 85 BLACK Using a dual relay pack to operate 12 volt accessories. The blue wire can be used for one channel and the green wire for another channel. Fused 12V power. PURPLE To 12 volt accessory. BLUE To 12 volt accessory. GREEN BROWN Do not connect. To CMD-2000 output.
PAGE 5
GND GND +12V BLACK WHITE GROUND-AT-REST Switch - contact positions vary with style WHITE REGULATOR AND SWITCH NOT INCLUDED BLACK BLACK TO SWITCH WHITE BROWN GREEN BLACK TO MOTOR WHITE TO SWITCH BLUE PURPLE CHASSIS GROUND CONSTANT-ON FUSED +12V WHITE TO MOTOR TO CONSTANT-ON FUSED 12V WIRE COLORS COMING FROM WINDOW REGULATOR MAY VARY DEPENDING ON MANUFACTURER. Connection Ball's, GM, Specialty, Dakota Digital, Springfield Streed Rod, and similiar power window systems.
PAGE 6
BLACK 6 CHASSIS GROUND POWER WIRES DUAL RELAY PACK BLACK RED WINDOW MOTOR WIRES 4-WIRE or 3-WIRE NOT GROUND-AT-REST SWITCH WHITE BROWN GREEN CHASSIS GROUND BLUE BLACK PURPLE CHASSIS GROUND CONSTANT-ON FUSED +12V BLUE TO CONSTANT-ON FUSED +12V DO NOT CONNECT NOTE THAT +12V WIRE ON POWER WINDOW SWITCH IS NO LONGER CONNECTED.
PAGE 7
POWER WINDOW SWITCH GROUND SPLICE REGULATOR AND SWITCH NOT INCLUDED 7 DO NOT USE DO NOT USE TO CONSTANT-ON FUSED +12V TO CONSTANT-ON FUSED +12V Special regulator or an additional relay module required for this style of wiring connection WHITE BROWN GREEN BLUE PURPLE CHASSIS GROUND CONSTANT-ON FUSED +12V DUAL RELAY PACK BLACK RED GREEN small wire RED BLUE small wire GREEN CONNECT TO CONSTANT-ON FUSED +12V WHITE BLUE GREEN small wire RED BLUE small wire DUAL RELAY PACK SEALED SWI
PAGE 8
GROUND +12V (BATT) GROUND 5-WIRE SWITCH +12V BATTERY GREEN BROWN WHITE BLUE PURPLE GROUND +12V BATTERY Connection to door lock motors with a 5-wire switch.
PAGE 9
GROUND +12V BATTERY Connection to door lock motors directly without a switch.
PAGE 10
DOOR LOCK SWITCH GND +12V GND GROUND +12V BATTERY DO NOT CONNECT +12V BATTERY FACTORY DOOR LOCK SYSTEM BLACK RED Connection to factory door lock motors with a 3-wire switch. GREEN small wire GREEN RED +12V BATTERY small wire BLUE WHITE DAKOTA DIGITAL not used not used GROUND CH 1 CH 2 * wire colors listed in ( ) are for alternate relay sockets found in some units.
PAGE 11
TECHNICAL SUPPORT If you need any assistance with or have any questions about the wiring or operation of your CMD-2000 remote system, please call the Dakota Digital technical assistance line at (605) 332-6513 or email us at dakotasupport@dakotadigital.com. TRANSMITTER PROGRAMMING All of the transmitters to be programmed into the system should be available. This sequence will erase any previously programmed transmitters.