- Dakota Digital, Inc. Automobile Parts User's Manual

ManualsBrandsDakota Digital ManualsAutomobile PartsMCL-3207

MAN# 650305:D

MODEL MCL-3207

3-3/8” SPEEDOMETER/TACHOMETER for 2008-2010 Rocker

GAUGE SETUP AND CALIBRATION

The setup menus are entered by holding the switch in while turning the

key on. The menus are as follows:

Menu Description

dIag read diagnostic codes

ADJUST adjust calibrate speed

vnIt select speed unit (MPH or km/h)

S SET miles to service setting

GEAR transmission gear display selection

PERF turn on/off performance displays

teMKp set temperature warning point

WXARN

RPM

set RPM shift warning point

WXARN

set low volt warning point

CL CAL adjust clock calibration

NIGHT turn on/off automatic night dimming

FUEL low fuel light setup

INFO display gauge revision code on speedometer

-odoMK one-time odometer preset

POWER & GROUND

The gauge is a direct plug in. Constant battery power and key switched power are supplied by the stock

harness along with ground.

STATUS AND WARNING INDICATORS

Several indicators are supplied on the stock wiring harness. Some of these may not be active on your

motorcycle. These include the security, engine, ABS, and low fuel.

LOW VOLTAGE WARNING

When the voltage drops below the warning limit with the engine running, LO and your current voltage will be

displayed. (default warning limit is 11.0V)

SPEEDOMETER & TACHOMETER

The speedometer and tachometer signals are read from the engine control module (ECM) over a data bus.

The speed can be calibrated to allow for differences in tires or gearing; calibration is discussed later.

The tach bar displays rpm x1000 with a range of 7000 rpm. The rpm can also optionally be shown on the message

display.

CLOCK

The clock uses a 12 hour format and can be set by pressing and holding the switch while the clock is

displayed. After the switch is held for a few seconds the hours will begin flashing. Momentarily pressing the switch will

change the hours, holding the switch will move to the minute set, and the minutes will begin flashing. Momentarily

pressing the switch will now change the minutes. Holding the switch will exit the clock set mode.

MOUNTING

The gauge will mount into the original housing using original grommet, screws, and mounting clip. Remove the

stock gauge by pulling it out of the housing using a slight rocking motion; it is held in place by a plastic mounting clip on

the back of the gauge. Once out, remove the two screws from the back of the mounting clip, then unplug the gauge.

Remove the grommet from the stock gauge and install it over the MCL-3207. Plug in the MCL-3207 and secure the

mounting clip with the two screws. Push the gauge firmly back into the hole making sure the clip lines up with the slots

in the dash and also watching that wires are not damaged or pinched. (see photos below and on next page)

IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles

(160km) of operation. See “Odometer preset” for instructions.

B V

MPH

km/h

RPM

Summary of content (5 pages)

PAGE 1
MODEL MCL-3207 3-3/8” SPEEDOMETER/TACHOMETER for 2008-2010 Rocker IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles (160km) of operation. See “Odometer preset” for instructions. GAUGE SETUP AND CALIBRATION The setup menus are entered by holding the switch in while turning the key on.
PAGE 2
SPEEDOMETER SETUP Press and hold the switch while turning the key on and starting the engine. Once the engine is running, release the switch. Press and release the switch to change the menu selection. dIAG Diagnostics mode for checking/clearing trouble codes • • • • Press and release the switch until “dIAG” is displayed, then press and hold the switch until “ - ” is displayed. Release the switch. The display will show “ENGINE”, “SECvRE”, ”ABS”, or “DoNE”.
PAGE 3
nIgHt Night Dimming Your display system has a dimming feature that dims the display intensity automatically at night. Normally the system is at full brightness for daytime viewing. To have the system at full brightness all of the time, go into the setup menu as described above and select “ngt” (night). Press and release the function switch to select “OFF” instead of “on”. Press and hold the function switch to save the new setting.
PAGE 4
PERF Performance menu setup • • • • The performance readings can be turned on or off. When they are turned off the odometer display will only toggle through the mileage readings. Press and release the switch until “PErF” is displayed, then press and hold the switch until “ - ” is displayed. Release the switch. The current setting will be displayed (on or oFF). Press and release the switch until the desired setting is displayed. Press and hold the switch until “ - ” is displayed to save the setting.
PAGE 5
Troubleshooting guide Problem Gauge will not light up. Possible cause Orange/White wire does not have power. Brown/Gray wire does not have power. Black wire is not getting a good ground. Gauge is damaged. Clock resets when key is off. Brown/Gray wire does not have constant power. Gauge lights up, but speed No data from ECM. will only show zero. Sensor is not sending a speed signal. Speed reading is incorrect. Gauge is not calibrated correctly. Gauge lights up, but tach No data from ECM.