ENGLISH MEGALINE EUPHONIA HELICON MK2 Item No. 951017-0-0A MENTOR IKON® LEKTOR® CONCEPT NN SUBWOOFER TABLE 1 DALI SUB P-10 DSS MANUAL P-10 DSS Speaker(s) pr. carton 1 x4 x1 x1 x1 MEGALINE EUPHONIA HELICON MENTOR MK2 IKON ® ENGLIS LEKTOR ® H - DEUTS CONCEPT CH - DANSK N SUBWOOFE R DAL I P-1 MAN 0 DSS UAL FIGURE 1 FIGURE 2 x1 FIGURE 3 20 Hz 100 Hz Movie DALI Denmark +45 9672 1155 www.dali-speakers.
FIGURE 4 FIGURE 5 A B DALI P-10 DSS SUB IR REMOTE CONTROL CINEMA HIFI PHASE FREQ VOL 1 2 H C D E F + G TABLE 2 - DALI SUB P-10 DSS TECHNICAL SPECIFICATIONS FIGURE 6 3 MEMORIES DALI SUB P-10 DSS Frequency Range [+/- 3] dB [Hz] 24 - 250 Input Impedance [kohm] 26 Maximum SPL [dB] 112 Crossover Frequencies [Hz] FIGURE 7 Low Frequency Driver(s) C B A Enclosure Type 40 - 120 1 x 10” long stroke active, 2 x 10” long stroke passive Closed box with dual passive radiators Bass Tuning Freque
UK CONTENTS ENGLISH 6 5
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE BACK PANEL. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. 1 2 3 4 5 6 7 8 The lightning flash within an equilateral triangle is intended to alert you to the presence of non insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock to persons.
UK CONTENTS 1.0 INTRODUCTION 8 2.0 UNPACKING 8 3.0 POSITIONING 8 4.0 CONNECTION 8 5.0 INSTALLING AND ADJUSTING 10 6.0 RUNNING-IN 14 7.0 OVERLOADING 14 8.0 MAINTENANCE 14 9.0 DISPOSAL 14 10.0 AMPLIFIER BACK PLATE 15 11.
1.0 INTRODUCTION Congratulations on your new DALI SUB P-10 DSS subwoofer. Please read this manual thoroughly before unpacking and installing the subwoofer in order to get the most from your purchase. You can find more information on our website: www.dali-speakers.com or by contacting your authorized DALI dealer. Remember to sign up for the DALI newsletter at www.dali-speakers.com. Enjoy! 2.0 UNPACKING Be careful not to damage the contents when unpacking the parts.
UK The subwoofer can be connected to your stereo or surround sound amplifier/receiver in two ways: 1) LINE input: The signal from the amplifier is low pass filtered inside the subwoofer using one or both of the LINE INPUTS. This way of connecting the subwoofer is typically used for connecting to a stereo amplifier/receiver. 2) LFE input: The signal from the amplifier is already filtered inside the amplifier when using the LFE input connector.
4.3 USING TWO DALI SUB P-10 DSS SUBWOOFERS In most cases you will achieve excellent results with one DALI SUB P-10 DSS. Use of two subwoofers is possible as a no-compromise stereo solution, or for reproduction of very powerful sound pressures in a stereo or surround setup in larger rooms.
UK 5.1 PHASE SETTING The PHASE switch of the subwoofer has 4 settings: 0°, 90°, 180°, and 270°. The phase setting will adjust the timing between the subwoofer and the main speakers. To set the phase, do the following: 1) 2) Turn up the volume of your subwoofer a little higher than you would normally do. Set the crossover point to maximum (120 Hz).
5.3.2 USING LFE INPUT When connecting your DALI SUB P-10 DSS to smaller speakers, e.g. the DALI EPICON 2, we recommend a crossover point of approximately 80 Hz. This must be entered in the menu system of your (pre-) amplifier. You might need to enter the ‘small’ setting when selecting type of front speakers in the AV receiver menu. Connecting larger speakers (typically floor-standing front speakers) will allow you to choose a lower crossover point, and to define your speakers as ‘large’ in the menu system.
UK 5.7 REMOTE CONTROL (see Figure 4) A) Standby ON/OFF Press to toggle between the two states (ON/OFF switch on the rear panel must be set to ON). NOTE: When the AUTO/MANUAL switch is set to AUTO, the subwoofer cannot be turned off with signal on the inputs. B) Mute Press to mute the subwoofer. The display on the front of the subwoofer will show “---”. Press again to un-mute the subwoofer. C) Cinema/Hifi mode Press the CINEMA/HIFI button to toggle between the two sound modes.
Display (see Figure 6) On the front of the subwoofer there is a translucent logo badge/display. The settings of the subwoofer can be seen on the display when the subwoofer is operated by the remote control or the buttons on the amplifier. 5.8 FACTORY RESET To reset all memory settings to factory default, press the ‘+’ and ‘-’ buttons on the back of the SUB P-10 DSS simultaneously for 10 seconds. This will set the values to: VOLUME: PHASE: CROSSOVER: SOUND MODE: 25 0 120 CINEMA 6.
UK 10.0 AMPLIFIER BACK PLATE (se Figure 7) A) VOLUME control: Press the ‘VOLUME’ button and adjust to the desired value using the ‘+’ and ‘-’ buttons. B) CROSSOVER control: Press the ‘CROSSOVER’ button and adjust to the desired value using the ‘+’ and ‘-’ buttons. C) PHASE switch: Press the ‘PHASE’ button and adjust to the desired value using the ‘+’ and ‘-’ buttons.
16
