User`s manual

106 • Part III: IFC PC2-CamLink User's Manual
IFC_ACTIVE_HIGH
LNK_DVAL_INPUT_MODE LNK_DVAL_INPUT_FIELD
LNK_DVAL_INPUT_VALID_DATA
CL2_DVAL_INPUT_MODE CL2_DVAL_INPUT_VALID_DATA
LNK_SPR_ENABLE IFC_DISABLE
IFC_ENABLE
Spare not supported in CamLink
spec.
LNK_SPR_POLARITY IFC_ACTIVE_LOW
IFC_ACTIVE_HIGH
Spare not supported in CamLink
spec.
Camera Timing Outputs
PC-CamLink
Param
Values PC2-CamLink
Param
Values
MAIN GROUP
No equivalent on PC-CamLink CL2_COMBINE_EXSYNC_PRI IFC_DISABLE
IFC_ENABLE
EXSYNC SIGNAL
OUTPUT GROUP
LNK_EXSYNC_ENABLE IFC_DISABLE
IFC_ENABLE
CL2_EXSYNC_ENABLE IFC_DISABLE
IFC_ENABLE
LNK_EXSYNC_POLARITY IFC_ACTIVE_LOW
IFC_ACTIVE_HIGH
CL2_EXSYNC_POLARITY IFC_ACTIVE_LOW
IFC_ACTIVE_HIGH
LNK_EXT_SYNC_OFFSET_TIME Range 0 to 1.87466e+007 ms, step size
0.069842 microseconds
CL2_EXT_SYNC_OFFSET_TIME Float range parameter,
min:0us, max:65535000us,
step size:1us
LNK_EXT_SYNC_ACTIVE_TIME Range 0.13968 to 1.87481e+007 step size
0.069842 microseconds
CL2_EXT_SYNC_ACTIVE_TIME Float range parameter,
min:1us, max:65535000us,
step size:1us
LNK_EXSYNC_MODE LNK_EXSYNC_FREE_RUNNING
LNK_EXSYNC_TRIG1
LNK_EXSYNC_TRIG2
LNK_EXSYNC_SOFT_TRIG
LNK_EXSYNC_SOFT_TRIG2
LNK_EXSYNC_VB_TRIG
External trigger source selects the
reference for EXSYNC.
LNK_EXT_SYNC_PERIOD_TIME Range: 0.34921 to 1.87481e+007 ms,
step size 0.069842 microseconds
Use CL2_FRAME_TRIG_FREQ for
area scan or
CL2_LINE_TRIG_CYCLE_TIME
for linescan
PRI SIGNAL OUTPUT
GROUP
LNK_PRI_ENABLE IFC_DISABLE
IFC_ENABLE
CL2_PRI_ENABLE IFC_DISABLE
IFC_ENABLE
LNK_PRI_POLARITY IFC_ACTIVE_LOW
IFC_ACTIVE_HIGH
CL2_PRI_POLARITY IFC_ACTIVE_LOW
IFC_ACTIVE_HIGH
LNK_PRI_OFFSET_TIME Range 0 to 1.87466e+007 ms, step size
0.069842 microseconds
CL2_PRI_OFFSET_TIME Float range parameter,
min:0us, max:65535000us,
step size:1us
LNK_PRI_ACTIVE_TIME Range 0.13968 to 1.87481e+007 ms, step
size 0.069842 microseconds
CL2_PRI_ACTIVE_TIME Float range parameter,
min:1us, max:65535000us,
step size:1us
LNK_PRI_END_LOCATION LNK_PRI_END_AT_LEN_BEGIN
LNK_PRI_END_AT_LEN_END
LNK_PRI_END_IS_START_DEPEND
No equivalent on PC2-CamLink
CAMERA CONTROL