DEHUMIDIFIER 150 PINT COMMERCIAL DEHUMIDIFIER USER MANUAL FOR MODEL: PACD150 Before using your commercial dehumidifier, please read this manual carefully and keep it for future reference, along with your receipt.
Table of Contents General Information................................................................................... 1 Important Safety Instructions..................................................................... 2 Structure Diagram..................................................................................... 3 Setup Instructions................................................................................. 4 – 5 Control Panel................................................................
Important Safety Instructions WARNING - to reduce the risk of fire, electrical shock or injury to persons or property: 1. Always operate the product from a power source of the same voltage, frequency and rating as indicated on the product identification plate. 2. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Never cut off the third prong. 3.
Structure Diagram 1. Metal handle 5. Air outlet grille 2. Control panel 6. Air inlet grille 3. Wheels 7. Power cord 4. Drain hose bracket 8. Drain hose NOTE: You will need to install the handle. Six bolts are included for the installation. WARNING DO NOT OBSTRUCT THE AIR INLET OR OUTLET.
SETUP Instructions IMPORTANT Place dehumidifier in the upright position. When transporting a dehumidifier to site, allow the dehumidifier to stand upright for 30 minutes before switching ON. This is necessary to allow the refrigerant system to stabilize and avoid system damage. SETTING UP THE DEHUMIDIFIER: Operate the dehumidifier in an enclosed area as this creates a drying chamber. Close all doors, windows and areas that open to external areas to maximize the dehumidifier’s water removal efficiency.
SETUP Instructions (continued) DRAINAGE: The dehumidifier pump connects to a plastic drainage hose. The hose is stored on the back of the appliance. Uncoil the entire hose, ensuring there are no kinks or restrictions, and place the unattached end into a drain or run outdoors. Ensure that draining running to the outdoors does not create a hazard that could cause someone to slip. Water drains MUST be checked regularly when used.
Control Panel 1. ON/OFF Key 5. PURGE Key 2. UP and DOWN Keys 6. HUMIDITY and TIME Display 3. Purging Indicator 7. TIME Key 4. Defrosting Indicator 8. Operating Indicator ON/OFF: Press the key to turn the unit ON or OFF. PURGE: Press the key to empty water from the pump reservoir. During normal operation the pump purges automatically when the reservoir is full. Use “PURGE” before moving the machine to avoid water spillage. The pump will close automatically after 40 seconds of continuous operation.
Control Panel (continued) TIME: Press this to display working hours and total working time. • Once the unit is running, the display will show the humidity setting (left) and current humidity (right). Humidity setting can be changed by pressing “Up” or “Down.” • Time settings are based on minutes. For example, if the display shows “0000:50,” this means that the unit has worked for 50 minutes since powered on.
Operating Instructions General Use: Press the ON/OFF key to turn the unit on. It will begin working automatically. After use, press ON/OFF key to turn the unit off. Water pump will turn on automatically for 40 seconds to drain the remaining water in the unit, then turn off automatically. ATTENTION: • DO NOT switch the power OFF by disconnecting at the main socket outlet. • To avoid water spillage, DO NOT move the dehumidifier for at least 3 minutes after turning the power OFF.
Maintenance To clean the air filter: Ensure the dehumidifier is turned OFF and the plug is removed from the power outlet before performing maintenance. The working performance of the dehumidifier will be greatly reduced if the filter becomes blocked. 1. Remove the filter as shown in the diagram below. 2. Vacuum any debris from the filter using the vacuum hose and nozzle attachment. 3. Using lukewarm water and a mild detergent, wash the filter and allow to air dry completely. 4.
Maintenance (continued) Changing the battery: The battery allows the user to check the total working time of the unit even when the unit is powered off. (Press the “T” button to check this.) 1. Remove the screws in the four corners of the control panel. 2. Once the screws are removed, carefully lift the control panel to access the PCB. 3. On the PCB is a 6F22 9V battery. Remove the battery and replace with a new battery. 4. Refit the control panel onto the PCB. 5. Replace the four screws.
Troubleshooting Please check the following troubleshooting tips before calling for assistance. PROBLEM CAUSE Dehumidifier No power to appliance. does not operate Dehumidifier collects little/no water Dehumidifier is operating but room is not drying SOLUTION Connect plug to power outlet. Power not turned on. Switch power on. E4 error is displayed. Check drainage flow.
ERROR CODES WARNING: DO NOT attempt to rectify errors using unqualified personnel. To remedy the following errors, a qualified professional is required. NOTE: With any error code, it is suggested to turn the unit off, wait five minutes, and then turn the unit on again. If the error code is still present, a qualified professional is required to fix the problem. CODE MEANING DISPLAY READING SOLUTION* E1 Coil sensor error Flashes every 30 seconds Replace coil sensor. Call for replacement part.
PURCHASE RECORD Purchase Date: Serial Number: Distributor: Tel.
DEHUMIDIFIER Distributed by: Perfect Aire, LLC 5151 Belt Line Rd. Suite 878 Dallas, TX 75254 877-365-6274 www.perfectaire.us Specification and performance data is subject to change without notice.