Danalock V3 BT HK EU Mounting guide
Table of contents Tools needed page 4 Contents of the Danalock box page 5 Parts involved 1. Remove the old cylinder 2. Pull out the old cylinder page page page 3. Adjust the new cylinder 4. Unscrew the small screws 5. Insert the spacer piece and brass tube Cylinder Size guide 6. Assemble the cylinder 7. Insert the adjustable cylinder 7 8 page 10 page 9 page 11-12 page 14 page 16 page page 9. Break the screws to the right length page Page 2 6 page 8.
Table of contents 10. Fasten the back plate to the cylinder page 18 Make sure that the lock still works! page 19 11. Give the tailpiece t he right length page 20 12. Attach the tailpiece adapter page 21 13. Fit the tailpiece page 22 14. Align the plate marks page 23 15. Fasten the Danalock page 24 16. Activate batteries page 25 17. Add the Danalock in the HomeKit App page 26 18. Calibrate the lock page 26 19. Dismounting page 27 20. LED-Signals page 28 21.
Tools needed: To mount the Danalock you need a Philips screwdriver and two pliers or a wire cutter.
Contents of the Danalock box Adjustable cylinder Danalock V3 4 small screws Rosette spacers Keys Tailpiece adapter Back plate Breakable screws Page 5 Cylinder brass tubes
1. Remove the old cylinder First you have to remove your current cylinder. Unscrew the lock-screw found in the mortise-plate on the side of the door.
2. Pull out the old cylinder Insert your key and turn it so the cam lines up with the body of the cylinder. Now pull out the cylinder.
3. Adjust the new cylinder Measure the back part (on the outside of your door) of the old cylinder from the middle of the screwhole and away (see illustration). Compare the length of the old cylinder to the length of the adjustable cylinder found in the box. Back part Outside Inside The tailpiece will always be irected towards the inside d of the door Measure fro m center of screwhole If the old cylinder and the adjustable cylinder matches - go to page 15.
4. Unscrew the small screws on both sides of the cylinder and pull it apart.
5. Insert the same size of spacer piece and brass tube to make the adjustable cylinder match the old cylinder. +7 7 Please look at the size guide on the next pages to find the right length for the spacer piece and the brass tube.
Size guide - When you adjust the size of the Danalock cylinder to the old cylinder you’ll have to exchange the brass tube in the center with another that fits the spacer piece. Here are the different combinations: Fits min. 35 mm The adjustable cylinder as it is in the box = Fits min. 40 mm = 7 +7 7 space piece Fits min.
Fits min. 50 mm = 15 +15 15 space piece Fits min. 55 mm = 22 +22 22 space piece Fits min.
6. Assemble the cylinder and screw the small screws back in on both sides of the cylinder.
7. Insert the a djustable cylinder Insert the new cylinder, and re-insert the lock-screw in the mortise-plate to fix the cylinder. (b) Do not tighten the screw too hard - make sure the cylinder functions correctly by locking and unlocking it w ith your hand.
8. The right rosette spacer To avoid pulling the cylinder out of place you need to find the right spacer or a spacer combination between the rosette and the back plate. � Unscrew the two breakable screws that holds the spacers together with the adjustable cylinder. Choose one or more spacers so they are flush with the rosette surface.
IMPORTANT! Avoid pulling the c ylinder out of place. It is important that the s pacer is flush with or sticks out from the hole in t he rosette plate.
9. Break the screws to the right length Depending on which spacer or spacer combination you chose, it is now important that the screws that fasten the cylinder to the back plate have the right length. Use this chart to find the right length: No spacers cut 30 mm 5 mm spacer cut 25 mm 10 mm spacer cut 20 mm 5+10 mm spacers cut 15 mm 10+10 mm spacers cut 10 mm 30 mm 25 mm 20 mm 15 mm 10 mm Use a wirecutter, two pliers or bend the screws forth and back several times in a vice to break them.
10. Fasten the back plate to the cylinder Now fasten the back plate to the c ylinder with the rosette spacer i n between them.
IMPORTANT! Make sure that the lock still works! Make sure that the lock still works properly by turning the tailpiece. If you can’t lock and unlock this way please loosen the cylinder screws.
11. Give the tailpiece t he right length To avoid damaging the Danalock you will have to shorten the new cylinder tailpiece to max. 35 mm from the door surface. Use two pliers or a wire cutter t o shorten the tailpiece.
12. Attach the tailpiece adapter Insert the green tailpiece adapter i n the center tube on the b ack side of the Danalock. Press on the adapter u ntil a click ensures i t is fixed firmly to the Danalock.
13. Fit the tailpiece to the middle of the housing base Fit the Danalock over t he back plate. Make sure the tailpiece hits the s lide in the middle o f the adaptor.
14. Align the plate marks Find the small marking on the edge of the back plate and align the mark on the back of the Danalock baseplate with it. Now you are sure to hit the notches on the back plate with the Danalock.
15. Fasten the Danalock Turn the Danalock clockwise until it clicks to fasten it to the back plate. NOTE: If you need to unfasten and retry, see “Uninstall instructions” at the end of the manual.
16. Activate batteries Pull out the plastic tab to activate the batteries. A light will flash to confirm the Danalock is ready. Note: If the batteries are disconnected, you will have t o re-calibrate the Danalock.
17. Add the Danalock in the HomeKit App When the Danalock has been mounted on the door it is ready to be set up with the Home app. Instructions on how to use the Home app can be found at: https://support.apple.com/en-us/HT204893 The HomeKit setup code can be found both inside the battery compartment and on the ”Simple Guidelines” leaflet. 18. Calibrate the lock The Danalock needs to be calibrated in order to function properly.
19. Dismounting If you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press while turning the lock counter-clockwise until the lock releases. This will not reset the lock or disconnect it from your account, but the lock may need to be re-calibrated if fastened to your door again.
20. LED-Signals A LED light on the Danalock indicates the status of several operations with different colours: LED-Mode Constant red till light finishes LED color Constant green till light finishes Status indication Lock has successfully locked Lock has successfully unlocked Constant white for 3 seconds Power on.
21. Configuring the Danalock V3 with click-commands You can configure the Danalock via the button found in the small hole on the top of the lock. When you click through settings, the LED will change color according to the following scheme. When you get to the setting you want to change wait for 5 seconds and the Danalock will react to your command. This gives you plenty of time to navigate to the right command.
Clicks Color Activity 4 Blue Brake and go back Turns the brake and go back functionality on or off. This setting will hold the latch back for 2 seconds to allow entrance. Everytime this command is entered the setting will switch to the next option. • Turning off will respond with one red blink when being set. • Turning on will respond with one green blink when being set. 5 Purple Auto lock timer Toggles between 3 auto locking settings: Off, short wait and long wait.
22. Firmware upgrade To install the latest firmware on your Danalock download the Danalock app on App Store and log in as a ”HomeKit only” user. Press the download icon on the front page in the app to start the firmware upgrade process. Make sure to keep your phone near the Danalock during the entire firmware upgrade process.
www.danalock.
