Danalock V3 EURO Mounting guide www.danalock.
Page 2
Table of contents Tools needed page 5 Parts involved page 5 Contents of the Danalock box page 6 1. Remove the old cylinder page 7 2. Pull out the old cylinder page 8 3. Adjust the new cylinder page 9 4. Unscrew the small screws page 10 5. Insert the spacer piece and brass tube page 11 Cylinder Size guide page 12 - 13 6. Assemble the cylinder page 14 7. Insert the adjustable cylinder page 15 8.
Table of contents 10. Fasten the back plate to the cylinder page 19 Check that the lock still works! page 20 11. Give the tailpiece t he right length page 21 12. Attach the tailpiece adaptor page 22 13. Fit the tailpiece page 23 14. Align the plate marks page 24 15. Fasten the Danalock page 25 16. Activate batteries page 26 17. Before downloading the Danalock app page 27 18. Download the Danalock app page 28 19. Dismount instructions page 29 20. LED-Signals page 30 21.
Tools needed: To mount the Danalock you need a Philips screwdriver and two pliers or a wire cutter.
Contents of the Danalock box Adjustable cylinder Small screwdriver Danalock V3 4 small screws Rosette spacers Keys Tailpiece adapter Back plate Breakable screws Page 6 Cylinder brass tubes
1. Remove the old cylinder First you have to remove your current cylinder. Unscrew the lock-screw in the mortise-plate on the side of the door.
2. Pull out the old cylinder Insert your key and turn it so the cam lines up with the body of the cylinder. Now pull out the cylinder.
3. Adjust the new cylinder Measure the back part (on the outside of your door) of the old cylinder from the middle of the screwhole and away (see illustration). In the Danalock box you’ll find an adjustable lock cylinder. Back part Outside Inside The tailpiece will always be irected towards the inside d of the door Measure fro m center of screwhole If the old cylinder and the adjustable cylinder matches - go to page 11. If they don’t please proceed to the next page.
4. Unscrew the small screws on both sides of the cylinder and pull it apart.
5. Insert the same size of spacer piece and brass tube to make the adjustable cylinder match the old cylinder. +7 7 Please look at the size guide on the next pages to find the right length for the spacer piece and the brass tube.
Size guide - When you adjust the size of the Danalock cylinder to the old cylinder you’ll have to exchange the brass tube in the center with another that fits the spacer piece. Here are the different combinations: Fits min. 35 mm The adjustable cylinder as it is in the box = Fits min. 40 mm = 7 +7 7 space piece Fits min.
Size guide - last part Fits min. 50 mm = 15 +15 15 space piece Fits min. 55 mm = 22 +22 22 space piece Fits min.
6. Assemble the cylinder and screw the small screws back in on both sides of the cylinder.
7. Insert the a djustable cylinder Insert the new cylinder, and re-insert the lock-screw in the mortise-plate to fix the cylinder. (b) Do not tighten the screw to hard - make sure the cylinder is working by locking and unlocking w ith your hand.
8. The right rosette spacer To avoid pulling the cylinder out of place you need to find the right spacer or a spacer combination between the rosette and the back plate. � Unscrew the two breakable screws that holds the spacers together with the adjustable cylinder. Choose one or more spacers so they flush with the rosette surface.
IMPORTANT! Avoid pulling the c ylinder out of place. It is important that the s pacer flushes or sticks out from the hole in t he rosette plate.
9. Break the screws to the right length Depending on which spacer or spacer combination you chose, it is now important that the screws that fasten the cylinder to the backplate have the right length. Use this chart to find the right length: No spacers cut 30 mm 5 mm spacer cut 25 mm 10 mm spacer cut 20 mm 5+10 mm spacers cut 15 mm 10+10 mm spacers cut 10 mm 30 mm 25 mm 20 mm 15 mm 10 mm Use a wirecutter, two pliers or bend the screws forth and back s everal times in a vice to break them.
10. Fasten the back plate to the cylinder Now fasten the back plate to the c ylinder with the mortise spacer i n between them.
IMPORTANT! Check that the lock still works! Make sure that the lock still works properly by turning the tailpiece. If you can’t lock and unlock this way please loosen the cylinder screws.
11. Give the tailpiece t he right length To avoid damaging the Danalock you will have to shorten the new cylinder tailpiece to max. 35 mm from the door surface. Use two pliers or a wire cutter t o shorten the tailpiece.
12. Attach the tailpiece adaptor Insert the green tailpiece adaptor i n the center tube on the backside of the Danalock. Press on the adaptor until a click ensures i t is fixed firmly to the Danalock.
13. Fit the tailpiece to the middle of the housing base Fit the Danalock over t he back plate. Make sure the tailpiece hits the s lide in the middle o f the adaptor.
14. Align the plate marks Find the small marking on the edge of the backplate and align the mark on the back of the Danalock baseplate with it. Now you are sure to hit the notches on the backplate with the Danalock.
15. Fasten the Danalock Turn the Danalock clockwise until it clicks to fasten it to the back plate. NOTE: If you need to unfasten and retry, see “Uninstall instructions” at the end of the manual.
16. Activate batteries Pull out the plastic tab to activate the batteries. A light will flash to confirm the Danalock is ready. Note: If the batteries are disconnected, you will have t o re-calibrate the Danalock.
17. Before downloading the Danalock app Your Danalock is now attached to the door. Download and open the Danalock app to finish setting it up. Leave the door open, so the lock isn’t influenced when calibrated.
18. Download the Danalock App Go to Google Play or App Store and download the Danalock App. When the App is installed you create a user profile by pressing the blue ring. You will use this profile each time you sign into the App. You now need to add your Danalock in the App. Press ”Add lock” at the bottom of the screen. A guide will lead you through the installation and configuration of your Danalock.
19. Dismount instructions If you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press while turning the lock counter-clockwise until the lock releases. This will not reset the lock or disconnect it from your account, but the lock may need to be re-calibrated if fastened to your door again.
20. LED-Signals A LED light on the Danalock indicates the status of several operations with different colours: LED-Mode LED colour Status indication Constant red till light finishes Lock has successfully locked Constant green till light finishes Lock has successfully unlocked Constant white for 3 seconds Power on.
21. How to operate the Danalock V3 with click-commands You can control the Danalock via a switch reached through the small hole on top of the lock. You have 5 seconds before the Danalock engages the activity, giving you plenty of time to click the switch the right number of times. Notice: If you make a wrong number of clicks you can cancel by clicking 7 times.
www.danalock.