Boeing Stearman PT-17 Instruction Manual

ManualsBrandsDancing Wings ManualsAircraft(BNF) DSMX/2 Compatible Micro RC Foam Boeing Stearman PT-17 Biplane Kit 450mm

KIT

机身拼装 Assemble the Fuselage

01-1

配件图仅做参考用，您收到的实物可能因为修改/优化的原因导致与图片有略有不同。

Photos shown here just for reference, the product you received maybe slightly differ from the photos due to

continuous improvement on products.

在两片A1的反面均匀涂抹泡沫胶。

在A2的两侧均匀涂抹泡沫胶。

Spread foam glue evenly on the

reverse sides of the two pieces of

A1.

Spread foam glue evenly on

both sides of A2.

把涂好胶水的A1粘到A2的两侧，粘

贴时对齐边缘及各对应的空位。

Glue the glued A1 to both sides

of A2, and align the edges and

corresponding spaces when

pasting.

把转向舵从机身切下，用模型刀切割转向舵与机身连接处，

切出45度斜面。

Cut the steering rudder from the fuselage, use a model

knife to cut the connection between the steering

rudder and the fuselage, and cut a 45-degree slope.

H1 H2

A1-2：机身 Fuselage

B1-2：机翼 Wing

B3：水平尾翼 Horizontal Tail

C：机翼支架 Wing Structs

D1-3：起落架，轮子

Landing Gear; Wheels

E1-2：碳片 Carbon sheet

F：碳杆 Carbon Rod

G：舵角 Servo Horn

H1-2：钢丝连杆

Steel Wire Linkage

J：热缩管

Heat-shrinkable Tube

I：马达座 Motor mount

01-3

机翼拼装 Assemble the Wing

在下机翼B2底面预留槽内嵌入E1碳

片，并用泡沫胶把碳片粘固在槽内。

Insert the E1 carbon sheet into

the reserved groove on the

bottom of the lower wing B2,

and fix the carbon sheet in the

groove with foam glue.

把舵机通电回中，并安装

一字型舵臂。然后切掉舵

机支架。

Power on the servo

back to the center, and

install a flat servo arm.

Then cut off the servo

bracket.

用模型刀在机身下机翼安装位置切开一个小口。

Use a model knife to make a small cut in the wing installation

position under the fuselage.

把02-1步骤粘好的机

翼翻转，装入舵机并把

舵机线放置到正面。(

如左图安装)此处舵机

不要粘。

Turn over the wing

glued in step 02-1,

install the servo and

place the servo line

to the front. (as

shown on the left)

Do not paste the

servo here.

如图所示，在机身预留的机翼插槽内涂抹泡沫胶，两面

均匀涂抹。

Apply the foam glue evenly on the reserved wing

slots of the fuselage as shown in the picture.

02-1

02-302-2

02-4 02-5

01-2

从02-4切开的口插入下机翼到机

身，注意机翼正反，有字一面朝

下，调整机翼居中后，按压粘固

并随预留槽使机翼呈一定弧度。

Insert the lower wing into the

fuselage from the cut in 02-4.

Pay attention to the front and

back of the wing, with the

words facing down. After

adjusting the center of the

wing, press and fix it and

follow the reserved groove to

make the wing curve.

02-6