Boeing Stearman PT-17 Instruction Manual

ManualsBrandsDancing Wings ManualsAircraft(BNF) DSMX/2 Compatible Micro RC Foam Boeing Stearman PT-17 Biplane Kit 450mm

如左图，截取合适长度的热缩管，把Z型钢丝和碳杆套再一起，加热热

缩管缩紧，然后点入少量CA胶加固。

As shown in the picture on the left, cut the suitable length of the

heat shrinkable tube, sleeve the Z-shaped steel wire and the

carbon rod together, heat the heat shrinkable tube to shrink it,

and then add a small amount of CA glue to reinforce it.

注意：2根连杆只做好一端的Z型头，另一端待后续步骤再制作。

Note: For the two connecting rods, only one end of the

Z-shaped head should be made, and the other end will be made

in subsequent steps.

连杆制作方法 Make the Connecting Rod

F 碳杆

carbon rod

J 热缩管

heat-shrinkable tube

H1 Z型钢丝

Z-shape steel wire

03-3

舵机的安装 Install the Servo

如左图，在机身中部安装舵机，上下

交错安装。舵机线从预留孔整理到同

一侧。

As shown in the picture on the

left, the servo is installed in the

middle of the fuselage, staggered

up and down. Arrange the servo

wires from the reserved holes to

the same side.

如上图，在转向舵上贴一段透明胶，然后把转向舵粘贴到机身尾翼上。

保留1mm间距。

As shown in the above picture, paste a piece of transparent glue

on the steering rudder, and then paste the steering rudder to the

tail of the fuselage. pls take care to keep 1mm spacing.

02-11

1mm

把水平尾翼插入机身

尾部，连接处用泡沫

胶粘固。

Insert the horizon-

tal tail into the tail

of the fuselage, and

fix the joint with

foam glue.

在转向舵下方与机身连接

处，用少量泡沫胶粘连。

Use a small amount of

foam glue at the

connection point

under the steering

rudder and the

fuselage.

02-11

GLUE

把钢丝连杆一端穿入舵

臂，另一端穿入舵角，预装

舵角在副翼上，并修剪舵

角插针长度。

Insert one end of the

steel wire linkage into

the servo arm, and the

other end into the

servo horn , pre-install

the servo horn on the

aileron, and trim the

pin length of the servo

horn.

在尾翼预留槽嵌入小碳

片，用泡沫胶粘固。

Insert a small carbon

sheet into the

reserved slot of the

tail wing and fix it

with foam glue.

调整好舵角后，涂抹泡

沫胶，把舵角粘固在副

翼上。

After adjusting the

servo horn, spread

the foam glue to fix

the servo horn on

the aileron.

02-7 02-8

02-9 02-10

02-12

03-1 03-2

把制作好的一端Z型头穿入舵机的舵

臂，然后参考尾翼上舵角的位置，

确定连杆合适的长度，并切除多余

的碳杆。

Insert the finished Z-shaped end

into the rudder arm of the

steering gear, and then refer to

the position of the rudder horn

on the tail to determine the

appropriate length of the

connecting rod, and cut off the

excess carbon rod.

然后对照步骤制作连杆另一端的Z型

头。

Then follow the steps to make

the Z-shaped head at the other

end of the connecting rod.

完成Z型头后，把Z型头穿入舵角，

把舵角用泡沫胶粘在舵面上。

After finishing the Z-shaped

head, insert the Z-shaped head

into the rudder horn, and glue

the rudder horn to the rudder

surface with foam glue.

连杆连接舵机与升降舵、转向舵

The connecting rod connects the servos to the elevator and rudder

继续拼装上机翼及起落架

升降舵

Elevator

转向舵

Rudder

GLUE

在上机翼B1底面预留槽内嵌入碳片，并用泡沫胶把

碳片粘固在槽内。

Insert the carbon sheet into the reserved

groove on the bottom of the upper wing B1,

and fix the carbon sheet in the groove with

foam glue.

把上机翼粘到支架上，

三处接触点粘固，并贴

合支架的弧度。

Paste the wing onto

the bracket and fix

the three contact

points to make it fit

the arc of the bracket.

GLUE

02-13

02-14

02-15

03-4

03-5

04-1

04-2 04-3

GLUE

D1 D1

D2*2

在下机翼上粘贴机翼支架，用泡沫胶粘固，并使

下机翼贴合支架的弧度。

Paste the wing bracket on the lower wing

and fix it with foam glue, and make the

lower wing fit the curvature of the bracket.