Dannmar Dannmar Equipment 646 Flinn Avenue Moorpark, CA 93021 Tel: 1-877-432-6627 R EQUIPMENT www.dannmar.com www.maxjaxusa.com MAXJAX TILT USER MANUAL MODEL: MAXJAX TILT PORTABLE LOW-RISE TILTING LIFT 6,600 MAX. POUND CAPACITY FOR USE IN UNIBODY CONSTRUCTION VEHICLES ONLY FRAME CHASSIS MAXIMUM WIDTH IS 61”- MINIMUM WIDTH 48” PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION.
TABLE OF CONTENTS IMPORTANT NOTICE / DEFINITIONS OF HAZARD LEVELS 3 IMPORTANT SAFETY INSTRUCTIONS 4-5 OWNER / EMPLOYER RESPONSIBILITIES 6-7 INSTALLER / OPERATOR PROTECTIVE EQUIPMENT PARTS INVENTORY / ASSEMBLY DIAGRAM 7 8 - 10 INSTALLATION INSTRUCTIONS / SELECTING SITE / FLOOR REQUIREMENTS 11 UNPACKING OF MAXJAX TILT 13 ASSEMBLY OF MAXJAX TILT 14 - 16 USING MAXJAX TILT 15 - 16 INSTALLING MAXJAX TILT UNDER VEHICLE 19 RAISE/LOWER/TILT MAXJAX TILT 20 - 21 FAQ’S 22 - 24 GENERAL DISCLAIMER
IMPORTANT NOTICE 1. Read this manual thoroughly before installing, operating, or maintaining this lift. 2. This lift is designed for indoor/outdoor use and should not be installed in a pit or depression. 3. When not in use, store in cool, dry interior space. 4. The floor/surface on which the lift is to be used should be smooth and flat as possible. 5. The lift has specific mechanical requirements as described in the Installation Instructions section of this manual. 6.
IMPORTANT SAFETY INSTRUCTIONS READ THESE SAFETY INSTRUCTIONS ENTIRELY Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures. Stay clear of any moving parts that can fall and cause injury. 1. READ ALL INSTRUCTIONS. 2. READ AND UNDERSTAND all safety warning procedures before operating lift. 3. KEEP AREA WELL LIT. 4. KEEP HAIR, LOOSE CLOTHING, FINGERS, AND ALL PARTS OF THE BODY AWAY FROM MOVING PARTS. 5. USE ONLY AS DESCRIBED IN THIS MANUAL.
NOTE: If attachments, accessories, or configuration modifying components that are in the load path, affect operation of the lift, affect intended vehicle accommodation are used on this lift and, if they are not certified for use on this lift, then the certification of this lift shall become null and void. Contact Dannmar Equipment for information pertaining to certified attachments, accessories, or configuration modifying components.
SAVE THESE INSTRUCTIONS OWNER / EMPLOYER RESPONSIBILITIES • Shall ensure that lift operators are qualified and that they are trained in the safe use and operation of the lift using the manufacturer’s operating instructions and regional requirements. • Shall establish procedures to periodically inspect the lift in accordance with the lift manufacturer’s instructions and regional requirements.
Failure to follow danger, warning, and caution instructions may lead to serious personal injury or death to operator or bystander or damage to property. Please read entire manual prior to installation. Do not operate this machine until you read and understand all the dangers, warnings and cautions in this manual. For additional copies or further information, contact: Dannmar Equipment 646 Flinn Ave. Moorpark, CA 93021 Tel: 1-877-432-6627 Fax: 1-805-530-1909 www.dannmar.
MAXJAX TILT ASSEMBLY Component Parts Identifier ITEM No. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MaxJax Tilt Frame Jack Support Stand Frame Platform Frame Platform Risers Frame Connecting Sleeves Frame Connecting Bolts Frame Connecting Washers Frame Connecting Nuts Positioning Wheels Drill Drive Adapter Positioning Wheel Screws Positioning Wheel Nuts Positioning Wheel Washers Wall Hanger Safety Locking Pin Track Rails (Optional) ©2019 DANNMAR EQUIPMENT. ALL RIGHTS RESERVED.
Technical Lift Capacity Dimensions 3000 kg/6614 lbs 1635 x 1300 x 115 mm Weight Height capacity 64-1/2” x 51-1/4” x 4-1/2” 45 kg / 99 lbs 60 cm / 23-1/2” Lift speed 30 - 40 seconds (depending on drill amperage and vehicle weight) Impact drill IS NOT ALLOWED Platform Width/Length 184.15mm X 800mm / 7-1/4" X 31-1/2" Maximum Outside Width of Platform 1638mm / 64" (1) Inside Dimension Minimum Outside Width of Platform 1270mm / 50" Inside Dimension 1136.
INSTALLATION INSTRUCTIONS TOOLS REQUIRED • • • • • 10*Amp/120Volt ½” Corded or Cordless Drill - DO NOT use Impact Drill (*less than 10 Amps may have difficulty in raising larger vehicle) Open-end Wrench Socket Wrench Phillips Screwdriver IMPORTANT NOTICE These instructions must be followed to ensure proper installation and operation of your lift. Failure to comply with these instructions can result in serious bodily harm and void product warranty.
UNPACKING OF MAXJAX TILT LIFT 1. Inspect shipping container. 2. Open shipping container by prying close tabs around crate. Verify all components are present. See Component Parts Identifier (page 8) 3.
UNPACKING OF MAXJAX TILT LIFT, continued 4. Remove, Risers (2), Lift Hangers (2) Screws (4) and Mollies (4) 5. Remove Safety Jack Stand (1) 6. Remove Parts Bag, cut strapping – for easier assembly, leave Tilt Mainframe in container.
ASSEMBLY OF MAXJAX TILT 1. Raise Arms up so both holes at top line up to each other. Coat the interior of holes with lithium grease to allow for easier components travel 2. Insert Frame Connecting Sleeves, Bolts, Washers and Nuts into Frame.
ASSEMBLY OF MAXJAX TILT, continued 3. Slide Platforms onto Sleeves, attach and tighten Bolts. Duplicate opposite set of Arms. 4. Flip Mainframe over and attach Positioning Wheels. 5. Assembly is complete.
ASSEMBLY OF MAXJAX TILT, continued Finished Images of MaxJax Tilt 16
While the factory has pre-greased the Gear Drive Box, we recommend that you add additional grease to Boxes (one per side) before first use. (example-Valvoline NLGI #2 GC-LB Complex Lithium EP Grease) Grease is designed to reduce friction of the gears and screw drive internally. NOTE: You will see grease on the side drive shaft as it opens and closes. This is normal and amount of grease will reduce with use. Wipe down excess after each use.
USING MAXJAX TILT 1. Insert Drill Drive Adapter into Drill and insert into Gear Box. 2. Once Drill has been inserted, lower Lift down to ground. 3. Once Lift has been lowered, you may now be able to use Lift under your vehicle.
INSTALLING MAXJAX TILT UNDER VEHICLE 1. Before using any lifting device, put vehicle in Park position and set Emergency Brake. 2. Roll MaxJax Tilt under vehicle closest to front wheels Slide Lift under vehicle and align Platforms under chassis frame rails. If pinch welds or body cladding interferes with Platform surface, place Riser Bars on Platforms before raising vehicle. 3.
RAISE/LOWER/TILT MAXJAX TILT TO RAISE VEHICLE • • • • • • • • • • • • • • Place vehicle in PARK and set parking brake Use on hard surfaces only Keep area clear around vehicle Measure width between chassis frame for correct arm location see manual for detail Roll lift under vehicle with the Drive Gearbox closest to front wheels Position lift arms under both the driver’s and passenger’s side of the vehicle’s frame. If alignment is necessary, adjust side-to-side.
USING MAXJAX TILT, continued TO TILT VEHICLE • Vehicles come in different configurations, engine locations, weights as well as shapes and sizes. o No vehicles weighing more than 6600lbs.
FAQ’s What is the maximum time a vehicle can remain lifted by the MaxJax Tilt? The MaxJax Tilt can keep a vehicle at a chosen height indefinitely. There is no time limit and the position is fixed. Always use the safety locking pin and jack stand before venturing under any lifted vehicle, no matter how long or short a time period.
What variety of vehicles can I lift with the MaxJax Tilt? FOR USE IN UNIBODY CONSTRUCTION VEHICLES ONLYFRAME CHASSIS MAXIMUM WIDTH IS 61”MINIMUM WIDTH 48” The MaxJax Tilt will lift the vast majority of passenger cars. The lifting platforms are designed to slide in and out to suit the sill widths or jacking points of most passengers’ cars. MaxJax Tilt is intended to be used to lift vehicles with unibody construction only.
What to do when there is a power outage – how can I lower the vehicle? In such case, use a ½ ratchet wrench to lower lift. Does the MaxJax Tilt need any maintenance (e.g. lubrication of the trapezoidal screw)? MaxJax Tilt does not need any maintenance. It contains a lifelong amount of lubrication without any need of a refill. Any tampering with the MaxJax Tilt hardware is not recommended and may affect the warranty.
MAXJAX TILT LIFT LIMITED WARRANTY* Better Products --‐ Better Service --‐ Better Value Duration: From the date of purchase by original Purchaser or 12--‐12 months from the date of shipment by DANNMAR or whichever comes first.
Warranty continued sole judgment have been altered damaged, misused, abused, badly worn, lost or improperly installed or maintained. This Warranty is null and void if the customer or any other person other than an authorized representative of DANNMAR has made any attempt to service or modify the tool prior to its return to DANNMAR under this Warranty. In no event will either party be liable for any damage caused by the other party’s failure to fulfill its responsibilities, under these terms and conditions.