Installation Instructions Ziga Zaga™ Collection Vessel Lavatory DC037350 CALL 1-888-328-2383 OR VISIT WWW.DANZE.COM © 2007 DANZE, INC. ALL RIGHTS RESERVED. Pub No. IM-DC037350/12-07.
Introduction to Danze Thank you for choosing Danze. We believe that elements in your bathroom should awaken your senses like a splash of cool water. That’s what you will experience with Danze. Danze is a manufacturer of high quality decorative plumbing products for your powder room, kitchen and bath. We offer a broad variety of products, designs & finishes to suit your own particular needs. You can feel confident that our products will provide years of beauty and trouble-free performance.
Product Dimensions 4. Cut out template (Z) at dashed line. Line up the centerline arrows on the template (Z) with the centerlines marked on the slab or counter top. Trace around the outside of the template (Z). This line indicates where the outer edge of the lavatory (A) will be after installation. 24” 20 3/4” 7 3/4” 14 5/8” 11” 15 3/8” 5. Cut out the inner circle on the template (Z) at the solid line.
10. Press down firmly on the lavatory rim to distribute the adhesive. 11. Remove excess adhesive with a dry cloth. 12. If there are any gaps visible between in the adhesive caulk, work additional adhesive caulk into the gap immediately. This will assure a water tight seal between the lavatory (A) and slab or counter top. Instrucciones para la instalación Lavabo de cubeta de Ziga Zaga™ Presentación de Danze Gracias por haber elegido Danze.
HERRAMIENTAS NECESARIAS Tijeras Nivel de carpintero Lápiz 2. Compruebe que la plancha o la encimera sea perfectamente plana a lo largo y a lo ancho por medio de un nivel. Taladro Sierra de perforación 3. Utilice un lápiz para marcar ligeramente el lugar donde se ubicará el lavabo (A) en la plancha o encimera. Rubbing Alcohol Material sellante Espátula para enmasillar Un trapo Alcohol de fricción Dimensiones de producto 4. Recorte la plantilla (Z) por la línea discontinua.
instructions d’installation 9. Coloque el lavabo (A) en la posición adecuada en la plancha o en la encimera utilizando como guía la línea exterior. Vasque Ziga Zaga™ Présentation de Danze Nous vous remercions de choisir Danze. Nous croyons que les différents éléments de votre salle de bain doivent éveiller vos sens comme une eau fraîche dont on s’asperge. C’est exactement l’effet que Danze produit. 10. Presione firmemente en el borde del lavabo hacia abajo para que el sellante se extienda. 11.
Outils requis Ciseaux 2. Utiliser un niveau pour s’assurer que la surface du dessus ou du comptoir est parfaitement plane autant sur la longueur que sur la largeur. Niveau de menuisier Crayon Perceuse Scie-cloche 3. Utiliser un crayon pour tracer faiblement les lignes centrales de la position du lavabo (A) sur le dessus ou sur le comptoir. Rubbing Alcohol Calfeutrant adhésif Couteau à mastic Alcool à friction Chiffon Dimensions du produit 4. Découper le gabarit (Z) le long du pointillé.
9. Mettre le lavabo (A) en place dans le dessus ou dans le comptoir, en se servant des lignes extérieures comme repère. 10. Appuyer fermement sur le bord du lavabo pour répartir l’adhésif. 11. Enlever le surplus d’adhésif à l’aide d’un chiffon sec. 12. S’il manque de calfeutrant adhésif à certains endroits, il faut en ajouter à cette étape-ci pour combler les espaces vides. Ceci permettra d’assurer qu’il y a un joint étanche entre le lavabo (A) et le dessus ou le comptoir. 13.