MANUAL ENGLISH Core Scratch Ordercode: D2312 Highlite International B.V.
Core Scratch Table of contents Warning ...............................................................................................................................................................................2 Unpacking Instructions .................................................................................................................................................2 Safety Instructions .........................................................................................................
Core Scratch Warning FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Core Scratch IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the system. Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never remove warning or informative labels from the unit. Never use anything to cover the ground contact.
Core Scratch Operating Determinations This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The minimum distance between light-output and the illuminated surface must be more than 0.5 meter. The maximum ambient temperature ta = 45°C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 35° C.
Core Scratch Microphone channel Mic input Connect a microphone here. Level control Adjusts the sound level output from the MIC channel. High control The High control adjusts the High frequency range. Range: -26dB to +12dB at 10kHz. Low control The Low control adjusts the Low frequency range. Range: -26dB to +12dB at 100Hz. Monitor section Phones output The PHONES output lets you plug in your headphones. Cue mix control This adjusts the signal of the phones output, between channel 1 and channel 2.
Core Scratch Main channels Selection switch (Line (31)/Line (32)) Assign Line (31) or Line (32) to Channel 1. Selection switch (Line (28)/Line (29)) Assign Line (28) or Line (29) to Channel 2. Gain control Adjusts the level of the audio signal input in each channel. High control The High control adjusts the high frequency range. Range: -26dB to +12dB at 10kHz. Low control The Low control adjusts the low frequency range. Range: -26dB to +12dB at 100Hz.
Core Scratch Master section Output L/R signal VU meter Displays the audio level output from the MASTER terminal. Master volume control Adjusts the audio level output from the MASTER terminal. Booth volume control Adjusts the audio level output from the Booth monitor. Bluetooth section Bluetooth Pair/Unpair button Push the Pair/Unpair button to pair a Bluetooth® device or to disconnect a paired Bluetooth device. Bluetooth connectivity LED Displays the status of the Bluetooth connectivity.
Core Scratch Rear AC adapter inlet Connects to a power outlet using the included AC power adapter. Channel 2 RCA unbalanced input Connect to a DJ player or a line level output component. Power switch Turns this unit’s power on and off. Line – Bluetooth switch Select input source Line – Bluetooth. Master RCA unbalanced output Connect to a power amplifier, etc. Channel 1 RCA unbalanced input Connect to a DJ player or a line level output component.
Core Scratch Connection Example D2312 9
Core Scratch Connection Cables Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely by using unsuitable or faulty cables.
Core Scratch Connect a Bluetooth device 1. 2. 3. 4. 5. 6. 7. Turn on your Bluetooth device. Power on the DAP Audio Core Scratch. Press the Pair/Unpair button on the DAP Audio Core Scratch. Navigate to your Bluetooth device’s setup screen, find “BT CORE” and connect. Note: If your Bluetooth device prompts for a pairing code, enter ‘0000’. The DAP Audio Core Scratch pairing LED will light up solid when it is 'paired'.
Core Scratch Product Specifications Model: DAP Audio Core Scratch Input Channels: 1x Microphone, combo XLR/Jack 4x Line RCA 1x Bluetooth 1x Record, RCA 1x Booth, RCA 1x Master unbalanced, RCA 1x Headphones, TRS 6.
Core Scratch Dimensions D2312 13
Core Scratch Notes D2312 14
©2013 DAP Audio