Use and Care Manual

ManualsBrandsDAP ManualsPaint8 oz. '33' Window Glazing

Technical Bulletin

2400 Boston Street, Suite 200, Baltimore, Maryland 21224

Phone: 410-675-2100 or 800-543-3840

Revised: 2/14/12

DAP

‘33’

Glazing

 For face glazing wood, metal and aluminum sash

 Forms an airtight, watertight seal

 Resists sagging, cracking and shrinking

 Interior/exterior use

Packaging: ½ pint tub, 1 pint tub, 1 quart tub, 1 gallon tub, 3.5 gallon tub

Colors: White

UPC Numbers: 7079812120, 7079812121, 7079812122, 7079812019, 7079812124

Company Identification:

Manufacturer: DAP Products Inc., 2400 Boston St., Ste. 200, Baltimore, Maryland 21224

Usage Information: Questions? Call 1-888-DAP-TIPS or visit dap.com & click on "Ask the Expert".

Order Information: 800-327-3339

Fax Number: 410-558-1068

Product Description:

DAP

‘33’

Glazing is a ready-to-use glazing compound that may be used for face glazing wood or

metal sash. Its knife grade consistency allows for smooth, easy application. DAP

‘33’

Glazing sticks

tightly to glass and sash and resists sagging, shrinking and cracking.

Suggested Uses:

For face glazing:

 wood window frames  metal window frames

NOTE: Do not use DAP

‘33’

Glazing on plastic windowpanes, porcelainized steel insulating panels,

insulated glass units with an organic seal, stained or leaded glass, any windowpane over 48 inches in

any run direction, any metal sash with rabbets over 1¼" wide, composite or composition panels,

channel glazing or on any surfaces not prepared as set forth below.

Surface Preparation, Application & Painting:

Surface Preparation

1. When re-glazing, remove from sash (i) all old glazing compound, (ii) any glazier points and/or

spring clips, (iii) glass, and (iv) any back bedding. Glass should be free from any residual glazing

compound and back bedding prior to reinstallation.

Summary of content (4 pages)

PAGE 1
Technical Bulletin 2400 Boston Street, Suite 200, Baltimore, Maryland 21224 Phone: 410-675-2100 or 800-543-3840 Revised: 2/14/12 DAP® ‘33’® Glazing     For face glazing wood, metal and aluminum sash Forms an airtight, watertight seal Resists sagging, cracking and shrinking Interior/exterior use Packaging: Colors: UPC Numbers: ½ pint tub, 1 pint tub, 1 quart tub, 1 gallon tub, 3.
PAGE 2
. All surfaces must be clean, dry, and free of frost or any substance that would compromise adhesion of the glazing material (e.g., wax, oil, grease, rust inhibitors, silicone residue, etc.). 3. For metal windows, sash corners must be sealed. All sashes must be safely installed and adjusted prior to glazing and sufficiently rigid to permit normal operation without excessive bending or flexing. Adjustment of freshly glazed sash will disrupt the adhesive bond of the glazing material to the glass and sash. 4.
PAGE 3
NOTE: The glazing compound may still feel soft and may not have full adhesion even after it has skinned over and attained a firm set. Accordingly, sash should be operated carefully for approximately three weeks on the average. Glazing may still be damaged if sash is handled carelessly. Full adhesion will develop within two to four months, depending on job conditions.
PAGE 4
Paint Requirements: Odor: Consistency: Vehicle: Volatile: Filler: Solids: Weight per Gallon: Temperature Service Range: Temperature Application Range: Shelf Life: Coverage: MSDS No.: Apply a high quality exterior-grade oil-based paint after product has skinned over and attained a firm set. A high quality exterior-grade latex paint can only be used if glazing surfaces are first primed with a high quality oilbased primer.