SDS

SDS Number: 00079201001 Revision Date: 2/13/2019
SAP Number:
n-Butyl acetate 123-86-4 1-5
GHS02-GHS06-
GHS07
H226-330-336
Isopropyl alcohol
67-63-0
1-5
GHS02-GHS07
H225-302-319-336
Ethyl acetate
141-78-6
1-5
GHS02-GHS07
H225-319-332-336
Attapulgite
12174-11-7
1-5
GHS07
H332
C.I. pigment yellow 42
51274-00-1
0.5-1.5
No Information
No Information
The text for GHS Hazard Statements shown above (if any) is given in the "Other information" Section.
4. First-aid Measures
FIRST AID - INHALATION: Move to fresh air.
FIRST AID - SKIN CONTACT: Wash off with soap and water.
FIRST AID - EYE CONTACT: Flush eye(s) immediately with plenty of water.
FIRST AID - INGESTION: Do not induce vomiting.
5. Fire-fighting Measures
UNUSUAL FIRE AND EXPLOSION HAZARDS: Eliminate sources of ignition: heat, electrical equipment, sparks and flames. Vapors
can form an ignitable mixture with air. Vapors can flow along surfaces to a distant ignition source and flash back. Vapors may form
explosive mixtures with air. Will ignite if exposed to intensive heat or open air. Store away from caustics and oxidizers. Containers
may explode if exposed to extreme heat. Empty containers retain product residue (liquid and/or vapor). Vapor can ignite potentially
causing an explosion.
SPECIAL FIREFIGHTING PROCEDURES: Use a self-contained breathing apparatus with full facepiece operated in pressure-
demand or other positive pressure mode. Cool fire-exposed containers using water spray.
EXTINGUISHING MEDIA: Alcohol Foam, Carbon Dioxide, Dry Chemical, Foam, Water Fog
6. Accidental Release Measures
ENVIRONMENTAL MEASURES: No Information
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: NOTE: Review fire hazards before proceeding with clean up.
Immediately eliminate sources of ignition. Keep people away from and upwind of spill/leak. Contain spilled material and remove with
inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal
regulations. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Read
all product instructions before using. Personal protective equipment should include impervious gloves, protective eye wear, and
suitable work clothes. Scrape up dried material and place into containers.
7. Handling and Storage
HANDLING: KEEP OUT OF REACH OF CHILDREN!DO NOT TAKE INTERNALLY. Remove all sources of ignition. Keep away from
open flames, hot surfaces and sources of ignition. Avoid breathing vapors. Provide adequate ventilation. Avoid heat, sparks and
open flames. Wear appropriate personal protection. Use only with adequate ventilation. Ensure fresh air entry during application
and drying. Avoid contact with skin and eyes. Do not breathe dust. While dry sanding, use of a NIOSH-approved dust mask is
recommended. Empty containers retain product residue (liquid and/or vapor). Vapor can ignite potentially causing an explosion. Do
not use in areas where static sparks may be generated.
STORAGE: Store away from sources of ignition and heat. Do not store at temperatures above 120 degrees F. Store containers
away from excessive heat and freezing. Store away from caustics and oxidizers. Keep containers tightly closed.
8. Exposure Controls/Personal Protection
Ingredients with Occupational Exposure Limits
Chemical Name ACGIH TLV-TWA ACGIH-TLV STEL OSHA PEL-TWA
OSHA PEL-CEILING
Limestone N.E. N.E. 15 mg/m3 TWA
total dust, 5 mg/m3
TWA respirable
fraction
N.E.
Acetone 250 ppm TWA 500 ppm STEL 1000 ppm TWA,
2400 mg/m3 TWA
N.E.
Cellulose 10 mg/m3 TWA N.E. 15 mg/m3 TWA
total dust, 5 mg/m3
TWA respirable
fraction
N.E.
Cellulose Acetate N.E. N.E. N.E. N.E.
Page 3 / 7