Installation & Assembly

ManualsBrandsDarby Home Co ManualsCandle-Style ChandeliersEberhart 3-Light Candle Style Classic / Traditional Chandelier

ASSEMBLING

ASSEMBLING &

& INSTALLATION

INSTALLATION

INSTALLATION INSTRUCTIONS

INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

ASSEMBLING

ASSEMBLING THE

THE

THE FIXTURE

FIXTURE

FIXTURE (

(

( Fig.

Fig.

Fig. 2)

2) .

1. Attach the pipe screw(A) onto the top coupling of the lamp body(D),

by turning it clockwise until tight.

2. Attach the short sleeve ( C ) onto the lamp holder, attach the candela

sleeve(B) insert the short sleeve(C).

3. .Install the light bulbs in accordance with the fixture specifications

NOTE:

NOTE: DO

DO NOT

NOT

NOT EXCEED

EXCEED

EXCEED THE

THE

THE SPECIFIED

SPECIFIED

SPECIFIED WATTAGE!

WATTAGE!

HANGING

HANGING THE

THE

THE FIXTURE

FIXTURE

FIXTURE (

(

( Fig.

Fig.

Fig. 1)

1. Shut off the power at the circuit breaker and remove old fixture

from ceiling, including the old single bar.

2. Carefully unpack new fixture and lay all the parts on a clear

surface.

3. Thread nipple (C) into loop (F) until snug.

4. Thread other end of nipple (C) with loop attached into single bar

(D) until snug.

5. Place lock washer (B) over end of nipple protruding t hrough single

bar and thread hex nut (A) onto nipple until tight.

6. Take this single bar assembly and mount to ceiling junction box

with junction box screws (E). Tighten screws securely with

screwdriver .

7. Us ing proper chain pliers to open one end link of the chain

provided and connect to the fixture loop (I). Close the link .

8. By measuring, determine correct number of links needed for

proper hanging height. Using proper chain pliers disconnect and

discard remaining chain.

9. Lace the fixture wires through the chain.

10. Slip loop collar (H) over the chain, then do the same with the

canopy (G).

11. Open the other end link of the chain and hang the f ixture on the

loop at the ceiling. Close the link.

12. Feed the fixture wires through the loop (F) and nipple (C) and pull

until taut.

13. Slide canopy (G) up flush to ceiling, secure using loop (H).

CONNECTING

CONNECTING THE

THE

THE WIRES

WIRES

WIRES (

(

( Fig.

Fig.

Fig. 3)

1. Take the black wire from the ceiling junction box and the smooth

wire leg from the fixture and twist bare ends together. Twist wire

connector onto end of wire until snug.

2. Repeat same process with white junction box wire and ribbed wire

leg of fixture wire. NOTE: Twist wires together in the same

direction you twist the wire connector onto wires.

3. If your junction box has a grounding wire (green or bare copper),

attach this wire and the bare copper wire from the fixture together

as step 1.If junction box has no ground wire, attach the bare copper

fixture wire to the green ground screw on the single bar.

4. Tuck these wire connections nea t ly into the ceiling outlet box and

then raise the canopy (G) all the way to the ceiling. Raise the loop

(H) and thread onto ceiling loop protruding through canopy .

Your

installation

installation is

is now

now

now complete.

complete.

complete. Return

Return

Return power

power

power to

to the

the

the junction

junction

box

box and

and

and test

test

test the

the

the fixture.

fixture.

Fig. 1

Fig. 2

Fig. 3

White or

HOUSE

Black

WIRES

(Hot)

Smooth

FIXTURE

WIRES

Black or

Ribbed

WIRES

FIXTURE

Bare Copper(Ground)

FIXTURE

WIRES

Copper

(Ground)

HOUSE

(Neutral)

WIRES

White

Bare

Green or

WIRES

HOUSE

Listed