Assembly Instructions

ManualsBrandsDarby Home Co ManualsFurnitureSusana 3 Piece Kitchen Island Set with Wood Top

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occuring to the wood parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level

Part List

Top

1 pc.

Top

1 pc.

Hardware List

Hex Wrench

1 pc.

Head Cap Bolt (short)

4 pcs. (+1 extra)

Cam Lock Screw

36 pcs.(+1 extra)

Magnet

2 pcs.

Machine Screw

8 pcs.

Pull Handle

4 pcs.

Small

Hex Wrench

1 pc.

Adjustable Pin

20 pcs. (+1 extra)

Wood Screw for Plinth

2 pcs. (+1 extra)

Wood Screw for Magnet

8 pcs. (+1 extra)

Wood Screw (short)

8 pcs.(+1 extra)

Wood Screw (long)

16 pcs.(+1 extra)

Cam Lock

36 pcs.(+1 extra)

Head Cap Bolt

10 pcs. (+1 extra)

Kitchen Island

For assembly see instructions in carton

Summary of content (7 pages)

PAGE 1
Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List A. Top 1 pc. B. Top 1 pc. Hardware List Small Hex Wrench 1 pc. Adjustable Pin 20 pcs. (+1 extra) Hex Wrench 1 pc.
PAGE 2
Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List (in this carton) C. Base 1 pc. D. Plinth 1 pc. I. Rail 2 pcs. F. Back Panel 1 pc. G. Back Panel 1 pc. H. Front Frame 1 pc. K.
PAGE 3
Assembly Instructions 2/6 IMPORTANT * Do not tighten up all the screws until each part is properly assembled. * You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * After assembly, item must be level to work properly. Use the included adjustable levelers to level. STEP 1 Attach Back Panel (F) to Back Panel (G) as shown.
PAGE 4
Assembly Instructions 3/6 STEP 4 H Attach Rails (I) and base unit in Step 3 to back panel unit in Step 2 with Cam Locks. Place Front Frame (H) onto unit with Cam Locks. H E I I H O I K L M STEP 5 Insert Cam Lock Screws into the pre-drilled holes of Plinth (K), Side Frame (L) and (M), Back Stretcher (O).
PAGE 5
Assembly Instructions 4/6 STEP 5 Attach Middle Panel (N) to Base (J) with Head Cap Bolts. P Attach Plinth (K) and Side Panel (L) to Base (J) with Cam Locks and Wood Screw. K N Attach Front Rail (P) to unit with Cam Lock. L J Wood Screw Q Head Cap Bolt STEP 6 O Attach Back Stretcher (O) and Divider (Q) to unit with Cam Locks. M Attach Side Panel (M) to unit with Cam Lock and Wood Screw. B Wood Screw STEP 7 Place Top (B) onto unit with Head Cap Bolts.
PAGE 6
Assembly Instructions 5/6 S Head Cap Bolt (short) STEP 8 Cam Lock Screw Cam Lock R Assemble Supports (R) and (S) with Cam Lock Screws and Cam Locks. S Attach unit in Step 4, Step 7 and support unit with Cam Lock and Head Cap Bolts (short). Head Cap Bolt (short) Head Cap Bolt Cam Lock Cam Lock Screw A STEP 9 Attach Doors (U) and (T) by sliding the door lift hinges into the side panels lift hinges. (See figure 3) U X T Place Top (A) onto unit with Head Cap Bolts.
PAGE 7
Assembly Instructions 6/6 Drawer (Z) Z1 Z3 Z4 Z2 Figure 1 STEP 1 MAKE SURE ROLLER IS ON THE BACK Attach Z1 to Z3 andZ4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. Attach Z2 to Z3 and Z4 using long wood screws (4X), tighten halfway. (see Figure 1) STEP 2 Slide Z5 into the grooves in Z3 and Z4. Be sure to push T5 all the way forward so it meets Z1.