User guide

ManualsBrandsDarex ManualsPower ToolsXT-3000 attachments manual (LEX050)

Congratulations on the purchase of your Darex

XT-3000 Large Drill Attachment. (21 mm—30

mm) As part of the assembly (see picture from

left to right) you should have a SA16565XA Large

drill alignment, SA16575CA Sharpening fixture,

and SA16500TA Large Drill Chuck.

By now you are familiar with the ‘quick disconnect’

feature of your XT-3000. Start by placing the

Large Drill Alignment on the top of your XT-

3000. Rotate the ‘Docking Lever’ clockwise to

securely lock the fixture in place. In a similar

manner, remove your current sharpening fixture

and replace it with the Large Drill Sharpening

Fixture.

Now would be a great

time to determine the

point angle of the drill

that is to be sharpened

and adjust both the

sharpening fixture and

alignment to that point

angle. The Sharpening

fixture is adjusted by

pulling the red lever

towards (counter

clockwise) the operator

and sliding the fixture to

the point angle desired. Lock the fixture by

returning the red lever to its original position. The

alignment is adjusted by

rotating the black lever

located at on the front of the

alignment fixture. As per the

decal, rotating the lever

towards the operator will

reduce the amount of relief

ground onto the drill and

pushing the lever away from

the operator will increase the relief. Placing the

pin at the midway point on the decal is a good

starting place for 118° drills. For 135°-150° drills

start with the alignment 2 marks towards the

operator. You can set the alignment at any setting

necessary to achieve the amount of relief desired.

Place the drill in the chuck and turn the chuck

knob clockwise until the drill slides freely through

the chuck jaws. Next slide the Chuck and drill into

the alignment rotating the chuck until one of the

‘cam dogs’ aligns with the

mating ‘notch’ in the fixture.

You will notice the opposite

‘dog’ aligns with a reference

mark machined into the

alignment fixture.

Now push the drill through the chuck until it

contacts the stop. Rotate the drill clockwise until

Large Drill Attachment

LEX050

Incorrect Correct

Summary of content (19 pages)

PAGE 1
Large Drill Attachment LEX050 Congratulations on the purchase of your Darex XT-3000 Large Drill Attachment. (21 mm—30 mm) As part of the assembly (see picture from left to right) you should have a SA16565XA Large drill alignment, SA16575CA Sharpening fixture, and SA16500TA Large Drill Chuck. By now you are familiar with the ‘quick disconnect’ feature of your XT-3000. Start by placing the Large Drill Alignment on the top of your XT3000.
PAGE 2
the outer edge of the cutting lip is touching the pins in the setting fixture. Firmly tighten the chuck by turning the knob clockwise while the chuck is still in the fixture. Remove the chuck and drill. The drill is now aligned and set to length to the chuck cam for the necessary grinding. Slide the chuck into the Sharpening fixture and rotate the Chuck clockwise applying slight pressure into the wheel. It is also necessary to keep the cam up against the swing cam follower bearing.
PAGE 3
Large Drill Attachment 43
PAGE 4
Large Drill Attachment LEX050 SA16615BA SA16585TA SA16652TA SA16657TA SA16645TA SA16500TA 44 Pivot Lock Lever Assembly PP16615BF Pivot lock lever PP16630FF 5mmX8mm SSS Timing Adjuster Assembly PP16283RF Material adjust spring PP16285TF Material adjust screw PP03924TF PS Latch Screw Handle PP16585TF Large Drill Timing Adjuster PP11015FF 1/8" Dowel Pins Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing Swing Bearing Assembly PP16655LF Swing Bearing PP16657TF Swing Bearing Bolt Spring
PAGE 5
XY Table Attachment X-Y Table No Sub Assemblies, Send in for Repair 45
PAGE 6
46
PAGE 7
Countersink Instructions LEX150 Congratulations on the purchase of your Darex XT-3000 Countersink Attachment. This fixture comes with 2 V-40 double angle collets and is used in conjunction with the Darex XT-3000 X-Y Attachment. X-Axis Knob Pivot Lock Knob Y-Axis Knob By now you are familiar with the ‘quick disconnect’ feature of your XT-3000. Begin by removing the current sharpening fixture and replacing it with the X-Y table. Secure it in place by rotating the ‘Docking Lever’ clockwise.
PAGE 8
To sharpen the tool, determine which angle the tool will be sharpened at. To adjust the X-Y table, loosen the Pivot Lock Knob and swing the table to that angle. Tighten the Pivot Lock Knob. Pivot Lock Knob Remove the Countersink Attachment from the top of the machine and place it on the X-Y Table. Again, rotate the Docking Lever clockwise to secure the fixture. Turn the machine ON. Using both the X and Y axis feed knobs, carefully position the cutter into the grinding wheel.
PAGE 9
Countersink Attachment 49
PAGE 10
Counter Sink Attachment LEX150 SA16823TA SA16860BA SA16830TA 50 Alignment Assembly PP16823TF Alignment Thumb Screw PP16820BF Alignment Arm PP16312FF 1/8"x2" Dowel pin PP08558FF Washer Swing Arm Assembly PP16860BF Swing Arm PP06136FF Dowel Pin PP08560LF Bearing CS Spindle lock assy.
PAGE 11
BRAD POINT ATTACHMENT LEX200 Congratulations on the purchase of the Darex XT3000 Brad point Attachment. (LEX200) This attachment consists of 2 pieces, 1 Sharpening Fixture, SA16900BA and 1 - 3mm – 12mm Chuck, SA16916TA. (The 12mm – 21mm Chuck, SA16918TA is available as an optional accessory) Both components are laser marked with a Brad Point icon to minimize confusion with other XT3000 attachments.
PAGE 12
Brad Point Attachment Brad Point Attachment LEX200 SA11790PA PP11745FF PP11790PF 1/4-20 x 1 SSS Point angle lock knob SA16652TA PP16652TF PP08560LF 52 Feed Bearing Bolt Feed Bearing
PAGE 13
STEP DRILL ATTACHMENT LEX 250 Congratulations on the purchase of your Darex XT- 3000 Step Drill Attachment. (LEX250). This attachment consists of 3 pieces, 1 Sharpening Fixture, SA16950BA, 1 Alignment Fixture, SA116970XA and a 3mm – 12 mm Chuck, SA16975TA. (The 12mm – 21mm Chuck, SA16980TA is available as an optional accessory) All 3 components are laser marked with a Step Drill icon to minimize confusion with other XT3000 attachments. the XT-3000.
PAGE 14
Rotate the Chuck until 1 of the alignment dogs rests firmly against the Alignment. Rotate the Pawl Locating Cam until the arrow lines up to the major diameter of the drill. As indicated by the logo on the Timing Arm, rotating it will have an impact on the amount of relief ground on the drill. Unless the drill is intended for a unique material, it is our recommendation that it stay in its normal location. Push the drill through the chuck until the pilot starts to pass through the Alignment.
PAGE 15
Step Drill Attachment 55
PAGE 16
Step Drill Attachment SA16950BA SA16652TA SA03413BA Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing Pawl Assembly PP03440FF 10-24 Nylon hex nut PP03435FF #10 nylon washer PP03420TF Pawl Retaining Pin PP03415TF Pawl Guide Pin PP03412BF Pawl Step Drill 3mm-12mm Chuck SA16975TA 56 Step Drill 3-12mm Chuck PP16400TF 3-12mm Body PP16975TF Step Drill 3-12mm Cam PP16410TF 3-12mm knob PP16415TF 3-12mm closing sleeve PP16420TF 3-12mm closing screw PP02404SF Thrust Washer PP16425SF 3-12mm - 12
PAGE 17
90º - 120º Drill Attachment LEX300 Congratulations on the purchase of your Darex XT-3000 90°-120° Sharpening Attachment. As part of the assembly you should have a Sharpening fixture (SA16995XA) and Drill Chuck (SA16890TA) range 3mm to 12mm. (SA016880TA Use the XT-3000 alignment to align the drill in the same manner that you are accustomed to. The Alignment tube should be positioned at the 118° mark.
PAGE 18
90º - 120º Sharpening Attachment 58
PAGE 19
90°- 120º Attachment SA16652TA SA16615BA SA16657TA SA16645TA SA16890TA Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing Pivot Lock Lever Assembly PP16615BF Pivot lock lever PP16630FF 5mmX8mm SSS Swing Bearing Assembly PP16655LF Swing Bearing PP16657TF Swing Bearing Bolt Spring Tensioner Assembly PP16645TF Spring Tensioner PP12280FF M6 x 1 x 8mm SSS 3-12mm 90° Chuck PP16400TF 3-12mm body PP16890TF 90° 3-12 mm Cam PP16410TF Knob PP16415TF Closing sleeve PP16420TF Closing screw PP02404S