User's Manual

ManualsBrandsDarfon Electronics ManualsComputers & Accessories27 MHz Mouse

N331 Wireless Mini Optical Mouse User’s Guide

Mouse

1. Left mouse button

2. Right mouse button

3. Scroll wheel

4. Charge port

5. Battery cover

6. Receiver storage compartment

7. Battery cover release button

8. Receiver release button

9. Connect button

10. Power ON/OFF Switch

Receiver

11. USB connector

12. Connect button

Charging Cable

13. Charging cable

System Requirements

• IBM compatible PC or Macintosh system

• Microsoft Windows 98SE, 2000, Me, XP or Mac OS X

•

An available USB port

Installation Instructions

Battery Installation

Step 1. Press the “Battery Cover Release Button” to remove the battery cover.

Step 2. Load two AAA rechargeable batteries into the mouse.

Step 3. Slide and lock the battery cover back into place.

NOTE:

 Please insert the batteries correctly as the pictures. Don’t insert the batteries upside down.

 Do not use Ni-Cd or alkaline batteries, or mix batteries of different types. Otherwise leakage of chemicals from or damages to the batteries may

occur.

Summary of content (8 pages)

PAGE 1
N331 Wireless Mini Optical Mouse User’s Guide Mouse 1. Left mouse button 2. Right mouse button 3. Scroll wheel 4. Charge port 5. Battery cover 6. Receiver storage compartment 7. Battery cover release button 8. Receiver release button 9. Connect button 10. Power ON/OFF Switch Receiver 11. USB connector 12. Connect button Charging Cable 13.
PAGE 2
Operating Instructions Step 1. To ensure correct operation, please make sure that the receiver is installed at least 20cm (8 inches) away from electronic devices (such as monitors or speakers). Step 2. Plug the receiver unit into a USB port on your system. The system will automatically detect the new hardware and install the device. Step 3. To activate, first press the CONNECT button on the receiver, and then the CONNECT button located on the bottom of the mouse within 10 seconds of each other.
PAGE 3
mouse is being charged. 2. If the mouse is going to remain unused for a long period of time, remove the rechargeable batteries from it to avoid unwanted battery power consumption. 3. DO NOT charge the battery unless it is labeled as a “rechargeable” battery. Trouble Shooting If you experience problems setting up your M310 Plus Wireless Mini Optical Mouse, please check the following: 1. Make sure the mouse “Power ON/OFF Switch” is in the ON position. 2.
PAGE 4
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 5
N332 Wireless Mini Optical Mouse User’s Guide Mouse 1. Left mouse button 2. Right mouse button 3. Scroll wheel 4. Charge port 5. Battery cover 6. Receiver storage compartment 7. Battery cover release button 8. Receiver release button 9. Connect button 10 2 3 11 1 8 7 9 6 4 5 10. Power ON/OFF Switch Receiver 11. USB connector 12. Connect button Charging Cable 13.
PAGE 6
NOTE: • The receiver/mouse may not function properly if placed on or near a metal surface. • If the mouse does not activate, please Repeat Step 3. • It is necessary to repeat Step 3 after any loss of power from battery replacement. Power-Saving Modes 1. The mouse can be manually powered OFF by using the “Power ON/OFF Switch”. 2. The mouse can be manually powered OFF by pressing both Left and Right Mouse Buttons and the Scroll Wheel Button simultaneously.
PAGE 7
Warranty Information Warranty • One year parts/labor from the date of purchase. • Please refer to the Warranty Terms and Conditions for your local region for further warranty details. • For more information, please visit: www.BenQ.
PAGE 8
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.