User's Manual

ManualsBrandsDarfon Electronics ManualsComputers & AccessoriesWireless Bluetooth Keyboard

Table Of Contents

Subject: PRODUCT ENGINEERING

SPECIFICATION

Part No.: 9Z.P5E**.***; Rev.: 0

Doc. No.:

201-C001

Project Code:

9Z.P5E81.001

Page 1 of 33

Model Name:

U10B

Release Notice

Table of Contents……………………………………………………………………………………Page

1. Introduction .........................................................................................................................................3

2. Electrical specifications ........................................................................................................................3

2.1 Pseudo N-key rollover .................................................................................................................3

2.2 Cables and Connectors ................................................................................................................3

2.3 Connectors to match with ...........................................................................................................3

2.4 Safety and EMI Requirements .....................................................................................................4

2.5 Membrane Switch Electrical Requirements ................................................................................5

2.5.1 Contact resistance: ..........................................................................................................5

2.5.2 Bounce: ............................................................................................................................5

2.5.3 Dielectric strength: ..........................................................................................................5

3. Mechanical Specification .....................................................................................................................5

3.1 General Items ..............................................................................................................................5

3.1.1 Overall Dimensions/ Weight............................................................................................5

3.1.2 Keycap Legend .................................................................................................................6

3.1.3 Row offsets ......................................................................................................................6

3.1.4 Key Pitch ..........................................................................................................................6

3.1.5 Keycap Texture ................................................................................................................6

3.1.6 Color ................................................................................................................................6

3.1.7 Flammability of materials (Unless otherwise specified): ................................................8

3.1.8 Key Switch Function.........................................................................................................8

3.2 Mechanical Requirements.........................................................................................................10

3.2.1 Switch Operating Characteristics (silent tactile): ..........................................................10

3.2.2 Smoothness: ..................................................................................................................11

3.2.3 KB Strengths: .................................................................................................................11

4. Environment Test Specification .........................................................................................................13

4.1 Environment test items for keyboard function: ........................................................................13

4.1.1 High Temperature Operation ........................................................................................13

4.1.2 High Temperature and High Humidity Operation .........................................................13

4.1.3 High Temperature Storage ............................................................................................14

4.1.4 High Temperature and High Humidity Storage .............................................................14

4.1.5 Low Temperature Operation .........................................................................................14

Form No.: A-01-001-09(111107) 保存期限:最新狀態保存單位:eGRNSystem

過期處置:背面紙

Summary of content (33 pages)

PAGE 1
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 1 of 33 Table of Contents……………………………………………………………………………………Page 1. 2. 3. 4. Introduction .........................................................................................................................................3 Electrical specifications ......................................................................................
PAGE 2
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 2 of 33 4.1.6 Low Temperature Storage .............................................................................................14 4.1.7 Temperature Shock .......................................................................................................14 4.2 Environmental Data for reference only ...................................
PAGE 3
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 3 of 33 1. Introduction These specifications will give a description on the U10B keyboard modules designed to be installed into the Notebook PCs. 64keys module for US versions. They are designed with excellent silent tactile feeling by switch-stroke up to 1.1±0.2 mm full stroke and feeling technology improvements.
PAGE 4
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 4 of 33 U10B 2.4 Safety and EMI Requirements 2.4.1 There shall be no over-standard EMI emitting from keyboard module while assembled on the Notebook PC housing so as to assist notebook PC successfully granted by FCC (class-B) & CE (class-B). 2.4.
PAGE 5
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 5 of 33 2.5 Membrane Switch Electrical Requirements 2.5.1Contact resistance: Test method – Apply finger load on the center of keycap down to bottom, resistance must meet the following: (pin end to end) 500-ohm max. (Initially) 1000-ohm max. (After life & Environmental testing) 2.5.
PAGE 6
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 6 of 33 3.1.2 Keycap Legend U10B: Legends are made by laser etching or printing. 3.1.3 Row offsets Defined by drawing. 3.1.4 Key Pitch 16.9 mm. 3.1.5 Keycap Texture U10B NBL keycap texture is MT 11010. U10B with BL keycap is polish 800. 3.1.
PAGE 7
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 7 of 33 UV coating: 大瑞 UV0093 Color: Clear Dry film thickness: 12~18 µm Gloss: 6±1 units at 60 degrees MCS-A0UN + MCS-A982 for U10B Gloss: 3±1 units at 60 degrees Sample appearance also needs to be approved by DARFON. Paint: Primer: Paint: 歐力生 ECONET EY MIDDLE GRAY BASE NO.
PAGE 8
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 8 of 33 MCS-A0C8 for U10B Color of legend: Print (Panton coolgray 8c) (3) Note: Specification of keycap color comparison. Refer to appendix A. 3.1.
PAGE 9
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 9 of 33 B. Normal keys C. Multiple key and spacebar D. Enter key E. Special key(Caps lock key) OR Form No.
PAGE 10
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 10 of 33 3.2 Mechanical Requirements 3.2.1 Switch Operating Characteristics (silent tactile): Key Switch Specification for regular keys Total Travel(Te) Regular Keys 1.1±0.2mm 1.1±0.3mm Small Keys 1.1±0.2mm 1.1±0.3mm Peak Force(Fp) 60±15g Min 50% of P1 60±15g Min 50% of P1 Peak Travel(Tp) 0.45±0.2mm 0.45±0.25mm 0.45±0.2mm 0.
PAGE 11
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 11 of 33 3.2.2 Smoothness: Press key at random, the key must be up and down actively and freely without slow return, rubbing or sticking motions. 3.2.
PAGE 12
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 12 of 33 Placing the keyboard such that the direction of keyboard operation is vertical, the maximum pulling force required to remove a key cap shall be measured. The above values are based on initial keycap removal test cycle.
PAGE 13
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 13 of 33 Figure. Keyboard Bending Strength With the keyboard is placed on the bench supporting both at top and bottom end, applying 9.8N (1 kgf) load to the center of keyboard, the keyboard bending should be 5mm maximum. During the test, the keycaps and scissors should not dislodge.
PAGE 14
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 14 of 33 4.1.3 High Temperature Storage The keyboard shall be able to withstand storage at 70oC without condensation continuously for a minimum 96 hrs. There must be no evidence of internal corrosion or bacteria – fungus growth after the test. 4.1.
PAGE 15
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.
PAGE 16
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 16 of 33 1. No evidence degradation & No flux activity on membrane assembly. (Discoloration may be acceptable if pass the following) 2. Max. loop Contact resistance (switch contacted) to be less than 1 KΩContact Resistance Increasing Less then 30 %. 3. Pass the basic function test & switch reaction test (4 strikes/sec). 4.
PAGE 17
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 17 of 33 actuation force at a 3-5 cycles per second frequency. After testing individual keys must function properly. If keycap have linkbar, after life test the linkbar can’t come off.
PAGE 18
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 18 of 33 5.2.3 Paint Keycap Test a. Adhesion (ASTM D3359-02) Test Parameters: Curved surfaces or surfaces too small (with one dimension less than 10mm) for Cross-cut – use Method A, “X-cut Tape Test” – Permacell, 3M 250 tape, (or equivalent) shall be used for testing purposes.
PAGE 19
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 19 of 33 Piece part test location for hardness test shall be determined by the piece part drawing. If the specific test location is not called out, test will be performed in the same area as color and gloss measurements.
PAGE 20
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 20 of 33 8. Thermal Ink Transfer H or harder 9. Plated Finish H or harder 10. Conductive Coatings H or harder 11. NCVM H or harder 12. ED H or harder 13. Carbon Fiber Composite H or harder c. Cure (Solvent Resistance) (ASTM D4752) Test Parameters: 1. 2K low bake 50 double rubs MEK (100%) 2.
PAGE 21
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Resistance Rating 5 4 3 2 1 0 Page 21 of 33 Description No effect on surface; no color on cloth after 50 double rubs. Burnished appearance in rubbed area; slight amount of color on cloth after 50 double rubs. Some marring and apparent depression of the film after 50 double rubs. Heavy marring; obvious depression in film after 50 double rubs.
PAGE 22
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 22 of 33 Item Requirement Test Wheel Felt, Taber CS-5 Load 200g Stroke 36 mm Frequency 3 cycles/second Number of cycles 100,000 5.2.4 Boiling Test Poured pure water into waterbath, and set up the constant temperature to 60℃.
PAGE 23
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 23 of 33 Judgment: Meet the KB module requirements and no keycaps failing out/all key switches function OK. 5.4 Drop Test (1) Drop Test – Packaged All keyboards in the bulk and individual shipping package shall be able to withstand being dropped on 3 edges and six sides.
PAGE 24
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 24 of 33 j. A flat drop with impact on the top. Judgment: Meet the requirement of no keycaps falling out & all key switches are OK in function. (2) Drop Test – Unpackaged All unpacked keyboards shall be fully operational and without mechanical degradation after being dropped from the heights below.
PAGE 25
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 25 of 33 (2) Shock test – square wave Keyboard Only Test: The keyboard shall withstand not less than a 60 G faired square wave with velocity at 5080 mm/sec (200 in/s). Judgment: The structure would remain in condition without loose keycaps and deformation of module. 5.5.2 Simple Shock Test (1) Measuring Method 1: Operating, non-packaged.
PAGE 26
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 26 of 33 5.6 Water Spill test Equipment required for test: Kept at room temperature, Water, Small containers Use a syringe or small container to pour 20cc (20 mL, about 2/3 fluid ounce) of water on three evenly spaced spots on the keyboard: A and S, G and H L and ;. The total liquid will be 60cc (60mL, about 2.03 fluid ounces).
PAGE 27
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 27 of 33 6. Keyboard Layout 6.1 U10B Layout Drawing U10B US Layout Form No.
PAGE 28
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 28 of 33 Appendix A (Appearance Spec) Item Normal Backlit IMR C Definition of Keycap surface A, B, C B B A A Viewing angle, distance and lighting requirement for inspection Discolored spots(異色點) Scratch for Keycap Flash for Keycap Shrink for Keycap 300mm, 45°(from horizontal), 800Lux ~ 1200Lux Surface A: <0.1mm² Surface B, C: <0.
PAGE 29
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 29 of 33 Coating heap(堆疊) ≤0.1mm² Appearance of laser etching legend Folding mark of MEM tail Arch for RUB Mylar Scratch for RUB Mylar ”e” & “i” width tolerance is ±0.05mm No function issue, mark can’t be through MEM tail width and broken surface can’t be acceptable.
PAGE 30
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 30 of 33 No warp spec: 0 ±1.5mm Warp spec: Short side: 0mm
PAGE 31
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 31 of 33 FCC Statement： Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.
PAGE 32
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 32 of 33 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 33
Release Notice Subject: PRODUCT ENGINEERING Part No.: 9Z.P5E**.***; Doc. No.: 201-C001 Rev.: 0 SPECIFICATION Project Code: 9Z.P5E81.001 Model Name: U10B Page 33 of 33 cULus Caution CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS ATTENTION IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS Form No.