ZHONE 6748-W1-EU,6748-W1-UK,6748-W1-NA User Manual VER: 1.
FCC Statement This equipment has been tested and found to comply with the limits for a C lass B digital device, pursuant to part 15 of t he FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
(2) This device must accept any interference received, including interference that may cause undesired operation. Caution! The m anufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. FCC - PART 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
User Manual Contents 1 Safety Precautions ............................................................................................. 1 2 Overview ............................................................................................................ 2 3 2.1 Application ............................................................................................. 2 2.2 Features ................................................................................................ 3 2.
User Manual 5.5.2 6 Update Software ....................................................................... 44 Q&A..................................................................................................................
User Manual 1 Safety Precautions Read the following information carefully before operating the device. Please follow the following precaution items to protect the device from risks and damage caused by fire and electric power: Use volume labels to mark the type of power. Use the power adapter that is packed within the device package. Pay attention to the power load of the outlet or prolonged lines. An overburden power outlet or damaged lines and plugs may cause electric shock or fire accident.
User Manual 2 Overview The xDSL Router integrates wireless LAN, USB, and VoIP service into one unit. It is designed to provide a simple and cost-effective xDSL Internet connection for a private Ethernet and 802.11b/802.11g/802.11n wireless network. The Router combines high-speed xDSL Internet connection, Ethernet uplink, IP routing for the LAN and wireless connectivity in one package.
User Manual 3G WAN service 2.2 Features User-friendly GUI for web configuration Several pre-configured popular games.
User Manual DSL router is targeted at the following platforms: DSL modems, wireless access points and bridge. 2.3 Standards Compatibility and Compliance Support application level gateway (ALG) ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.hs) ITU G.992.3 (ADSL2) ITU G.992.5 (ADSL2+) ITU G.993.1 (VDSL) ITU G993.2 (VDSL2) 3G (WCDMA, CDMA2000, TD-SCDMA) ANSI T1.413 Issue 2 IEEE 802.3 IEEE 802.3u IEEE 802.11b IEEE 802.11g IEEE 802.
User Manual 3 Hardware Description and Installation Note: The figures in this document are for reference only. 3.1 Hardware Description 3.1.1 Front Panel Figure 1 Front panel The following table describes the indicators on the front panel. Indicator Color Status Description On Green Power Red DSL Green The software is upgrading. Off The device is powered off. On The device is initiating. Blink The software is upgrading. On DSL link has established. Blink The DSL line is training.
User Manual Indicator Color Status Description Ethernet cable. On LAN 1/2/3/4 WiFi Green Green Blink The Ethernet interface is disconnected. On WIFI is enabled. Blink On Green Blink Off On USB1/2 Phone1/2 Green Green interface. Off Off WPS The Ethernet interface is connected. Data is being transmitted through the Ethernet Data is being transmitted through the wireless interface. WIFI is disabled. Connection succeeds under Wi-Fi Protected Setup.
User Manual 3.1.2 Rear Panel and Side Panel Figure 2 Rear panel Figure 3 Side panel The following table describes the interfaces and the buttons. Interface Description DSL Phone1/2 LAN 4~1 WAN Reset USB1/2 RJ-11 port. Connect the router to DSL connector or splitter through telephone cable. RJ-11 port, using the telephone cable to connect the telephone set. RJ-45 port, for connecting the router to a PC or another network device. For connecting Ethernet cable to provide Ethernet uplink.
User Manual Interface Description This button is used for enabling WPS PBC mode. If WPS is enabled, WPS press this button, and then the wireless router starts to accept the negotiation of PBC mode. Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small circular hole on the rear panel.
User Manual Phone: Connect to a telephone set Step 2 Connect the LAN port of the router to the network card of the PC through an Ethernet cable. Step 3 Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the router. The followig figure displays the connection of the DSL router, PC, and telephones. Figure 4 Connecting the DSL router Note: If you use 3G WAN service, connect the 3G USB data card to the USB port of the router.
User Manual 4 PC Network Configuration and Login 4.1 PC Network Configuration Each network interface on the PC should either be configured with a statically defined IP address and DNS address, or be instructed to automatically obtain an IP address using the network DHCP server. DSL router provides a DHCP server on its LAN and it is recommended to configure your LAN to automatically obtain its IP address and DNS server IP address.
User Manual Figure 5 IP and DNS configuration TCP/IP configuration steps for Windows XP are as follows: Step 1 Choose Start > Control Panel > Network Connections. Step 2 Right-click the Ethernet connection icon and choose Properties. Step 3 On the General tab, select the Internet Protocol (TCP/IP) component and click Properties. Step 4 The Internet Protocol (TCP/IP) Properties window appears.
User Manual Step 5 Select the Obtain an IP address automatically radio button. Step 6 Select the Obtain DNS server address automatically radio button. Step 7 If you want to set the IP address and subnet mask manually, you can set the IP address and subnet mask of the computer to 192.168.1.x and 255.255.255.0 respectively. The range for x is from 2 to 254. Step 8 Click OK to save the settings. 4.
User Manual Figure 6 Login page After logging in to the DSL router as a super user, you can query, configure, and modify all the settings, and diagnose the system 5 Web-Based Management This chapter describes how to use Web-based management of the DSL router, which allows you to configure and control all of DSL router features and system parameters in a user-friendly GUI. 5.1 Quick Setup Choose Quick Setup and the following page is displayed.
User Manual VPI (Virtual Path Identifier): The virtual path between two points in an ATM network, and its valid value is from 0 to 255. VCI (Virtual Channel Identifier): The virtual channel between two points in an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known protocols). Encapsulation Mode: LLC/SNAP-BRIDGING, or VC/MUX Protocol: You can select the following items from the drop-down list: PPPoE, DHCP, PPPoA, IPoA, or Bridge.
User Manual PPP Username: The correct user name provided by your ISP. PPP Password: The correct password provided by your ISP. Use Static IP Address: If this function is disabled, the modem obtains an IP address assigned by an uplink equipment such as BAS, through PPPoE dial-up. If this function is enabled, the modem uses this IP address as the WAN IP address. SSID: The service set identification (SSID) is a unique name to identify the router in the wireless LAN.
User Manual 5.2 Advanced Setup 5.2.1 Layer2 Interface 5.2.1.1 ATM Interface Choose Advanced Setup > Layer2 Interface > ATM Interface . In this page, you can add or remove to configure DSL ATM Interfaces. Click Add to add ATM Interface and the following page appears.
User Manual In this page, you can enter this PVC (VPI and VCI) value, and select DSL link type (EoA is for PPPoE, IPoE, and Bridge.), encapsulation mode, service category. VPI (Virtual Path Identifier): The virtual path between two points in an ATM network, and its valid value is from 0 to 255. VCI (Virtual Channel Identifier): The virtual channel between two points in an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known protocols).
User Manual Select Scheduler for Queues of Equal Precedence as the Default Queue: Weighted Round Robin or Weighted Fair Queuing. Click Apply/Save to save the configuration, and return the following page: If you want to remove this Interface, please select the Remove check box and click Remove. 5.2.1.2 PTM Interface Choose Advanced Setup > Layer2 Interface > PTM Interface, and the following page appears. In this page, you can add or remove to configure PTM WAN Interfaces.
User Manual In this page, you can select scheduler for queues of equal precedence and enter the queue value. Click Apply/Save to save configuration. 5.2.1.3 ETH Interface Choose Advanced Setup > Layer2 Interface > ETH Interface, and the following page appears. In this page, you can add or remove to configure ETH WAN Interfaces.
User Manual Click Add and the following page appears. In this page, you can select a ETH port. Click Apply/Save to save configuration. Note: If ETH Interface is selected, there are two WAN service types (PPPoE and IPoE). 5.2.2 WAN Service Choose Advanced Setup > WAN Service, and the following page appears. In this page, you are allowed to add, remove, or edit a WAN service. Note: If PTM Interface is selected, there are three WAN service types: PPP over Ethernet (PPPoE), IP over Ethernet, Bridging.
User Manual 5.2.2.1 Adding a PPPoE WAN Service This section describes the steps for adding the PPPoE WAN service. Step1 In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page. (At first, you must add a proper ATM or PTM interface for this WAN service.) Step2 In this page, you can select a ATM Interface for the WAN service. After selecting the ATM interface, click Next to display the following page.
User Manual Step3 In this page, select the WAN service type to be PPP over Ethernet (PPPoE). Click Next to display the following page.
User Manual Step4 In this page, you can modify the PPP username, PPP password, PPPoE service name and authentication method. PPP Username: The correct user name provided by your ISP. PPP Password: The correct password provided by your ISP. PPPoE Service Name: If your ISP provides it to you, please enter it. If not, do not enter any information. Authentication Method: The value can be AUTO, PAP, CHAP, or MSCHAP. Usually, you can select AUTO. Enable Fullcone NAT:.
User Manual does not stop, unless the modem is powered off and DSLAM or uplink equipment is abnormal. PPP IP extension: If you want to configure DMZ Host, you should enable it first. Use Static IPv4 Address: If this function is disabled, the modem obtains an IP address assigned by an uplink equipment such as BAS, through PPPoE dial-up. If this function is enabled, the modem uses this IP address as the WAN IP address. Enable PPP Debug Mode:Enable or disable this function.
User Manual Step7 In this page, you can obtain the DNS server addresses from the selected WAN interface. Click Next, and the following page appears. Step8 In this page, it displays the information about the PPPoE settngs. Click Apply/Save to save and apply the settings. 5.2.2.2 Adding a Bridge WAN service This section describes the steps for adding the Bridge WAN service. Step1 In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page.
User Manual or PTM interface for this WAN service.) Click the Add button to display the following page. Step2 Select the proper ATM Interface and then click Next to display the following page.
User Manual Step3 In this page, you can select the WAN service type, and modify the service description for this service. After finishing setting, click Next to display the following page.
User Manual Step4 In this page, it displays the information about the bridge settngs. Click Apply/Save to save and apply the settings. You can modify the settings by clicking the Back button if necessary. 5.2.3 3G WAN Service Choose Advanced Setup > 3G Wan Service , and the following page appears. This page is used to configure 3G connection. If you want to access the Internet through 3G connection, a 3G network card is required. Connect the 3G network card to the USB interface of the Router.
User Manual In this page, you are allowed to configure the settings of the 3G USB modem. Enable USB Modem: If you want to access the Internet through the 3G network card, you must enable the USB modem. User Name: Username provided by your 3G ISP. Password: Password provided by your 3G ISP. Authentication Method: Select a proper authentication method in the drop down list. You can select Auto, PAP, CHAP, or MSCHAP. APN: APN (Access Point Name) is used to identify the service type.
User Manual – - DSL: If the DSL is disconnected, the 3G starts to dial. – - IP connectivity: If the system fails to ping the specified IP address, the 3G starts to dial. After finishing setting, click the Apply/Save button to save the settings. You may also click the Auto Setting button to automatically configure the 3G connection. 5.3 Wireless Choose Wireless and the submenus of Wireless are shown as below: 5.3.1 Basic Settings Choose Wireless > Basic to display the following page.
User Manual This page allows you to configure the basic features of the wireless LAN interface. Enable Wireless: Enable or disable the wireless function. Hide Access Point: if you want to hide any access point for your router, select this option, and then a station cannot obtain the SSID through the passive scanning. Clients Isolation: When many clients connect to the same access point, they can access each other.
User Manual This page allows you to configure the security features of the wireless LAN interface. In this page, you can configure the network security settings by the Wi-Fi Protected Setup (WPS) method or setting the network authentication mode.
User Manual There are 2 primary methods used in the Wi-Fi Protected Setup: PIN entry, a mandatory method of setup for all WPS certified devices. – Enter STA PIN: If you select it, you need to enter the station PIN from – Use AP PIN: The PIN is generated by AP. client. Push button configuration (PBC), an actual push button on the hardware or through a simulated push button in the software. (This is an optional method on wireless client).
User Manual 5.4.1 VoIP Status Choose Voice > VoIP Status and the Voice Status page appears. In the Registration Status field, Up means registered successfully, Down means unregistered, Disable means account is not enabled. 5.4.2 SIP Basic Setting Choose Voice > SIP Basic Setting, and the following page appears.
User Manual 35
User Manual Figure 7 SIP Basic Setting Bound Interface Name: you can select the bound interface name from the drop-down list. SIP Local Port: Set the SIP local port of the gateway, the default value is 5060. SIP local port is the SIP UA (user agent) port. SIP domain name: Enter the SIP domain name that you want to set. Use SIP Proxy: Select the checkbox of Use SIP Proxy, if your DSL router uses a SIP proxy. SIP proxy allows other parties to call DSL router through it.
User Manual – SIP Outbound Proxy port: The port that the outbound proxy is listening on. By default, the port value is 5060. Use SIP Registrar: Select the checkbox of Use SIP Registrar to register with the proxy. You can register your user ID on the SIP registrar. SIP registrar works with SIP proxy, allowing other parties to call DSL router through it. When it is selected, the following fields appear. – SIP Registrar: The IP address of the SIP registrar.
User Manual 5.4.3 SIP Advanced Setting Choose Voice > SIP Advanced Setting, and the following page appears.
User Manual 39
User Manual Figure 8 SIP Advanced Setting Line: It displays the line you want to configure. Call waiting: If call waiting is enabled on a line, you can hear the call waiting tone during a call, press FLASH on the phone to answer the second call. The first call is automatically placed on hold. To switch between calls, press FLASH again. Select Call waiting to enable this feature. Call forward feature settings (Busy or All) take priority over the call waiting feature.
User Manual Select the checkbox of Anonymous calling to enable this feature. You can also dial *68 to enable this feature. Dial *82 to disable this feature. DND It is a feature to reject all incoming calls. Select the checkbox of DND to enable this feature. You can also Dial *78 to enable the feature. Enable Call Return: Select the check box to enable this function. Fax Negotiate Mode: You can select it from the drop-down list. Bypass Codec: You can select it from the drop-down list.
User Manual – RFC2833: Use RTP packet to encapsulate DTMF events, as specified in RFC 2833. – InBand: DTMF events are mixed with user voice in RTP packet. SIP Transport Protocol: Select the transport protocol to use for SIP signaling. Note that the SIP proxy and registrar need to support the protocol you select. Enable Local Supplementary Service: Select the checkbox to enable the supplementary service settings by the telephone set.
User Manual Vodsl Console Log Level: Select it from the drop-down list. SIP Log Server Settings: Set SIP log server IP address and port, then the log message of the VoIP is sent to the device which IP address you set to. If you want use this function, both of the IP address and port must be set correctly. Gain Settings: Gain is a measure of the ability of a circuit (often an amplifier) to increase the power or amplitude of a signal. You can increase or decrease ingress gain and egress gain.
User Manual In the page, you can modify the username and password of different users. After finishing setting, click the Apply/Save button to save and apply the settings. 5.5.2 Update Software Choose Management > Update Software, and the following page appears. If you want to upload the software, click the Browse… button to choose the new software, and then click the Update Software button. Note: When software update is in progress, do not shut down the router.
User Manual 6 Q&A (1) Q: Why all the indicators are off? A: Check the following: The connection between the power adaptor and the power socket. The status of the power switch. (2) Q: Why the LAN indicator is off? A: Check the following: The connection between the ADSL router and your computer, hub, or switch. The running status of your PC, hub, or switch. (3) Q: Why the DSL indicator is off? A: Check the connection between the “DSL” port of router and the wall jack.
