Tally Dascom 1325 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 1325 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 1325 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 1325 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 1325 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 1325 Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. Данная инструкция должна быть всегда доступна каждому пользователю. Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.
Tally Dascom 1325 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. Consulte sempre um técnico qualificado para executar uma reparação . Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 1325 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Tally Dascom 1325 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 1325 X
Tally Dascom 1325 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PLACING THE PRINTER ........................................................................................................................................ 2 PRINTER COMPONENTS ......................................................................................................................................
Tally Dascom 1325 DIAGNOSTIC FUNCTIONS ................................................................................................................................... 41 FIRMWARE UPDATE ........................................................................................................................................... 42 8 GENERAL SPECIFICATIONS ....................................................................................................................... 43 9 INTERFACES .................
Tally Dascom 1325 1 Unpacking Guide Place your packaged printer on a solid base. Make sure that the “Up” symbols point in the correct direction. Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer.
Tally Dascom 1325 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: Never place the printer near to any flammable gas or explosive substances.
Tally Dascom 1325 Component Gap Lever Function Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Paper Guides Paper Loader Adjust positioning of single sheet paper. Paper Holder For single sheet in larger sizes. Paper Slot For friction feed (forward). Print Head 24-pin printing mechanism Cover Paper Feed Lever Protects print head and other components inside, and reduce noise. Shows printer status, for printer setup.
Tally Dascom 1325 2 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions and ② on the ribbon cassette into the printer mounting. 3. Press the ribbon frame onto the print head. 4. Turn the ribbon knob ④ in clockwise direction until the ribbon fabric is taut.
Tally Dascom 1325 Install the Paper Loader As shown in the picture below, ensure the sheet feeder fingers fit into the slots in front of the printer. Push in the sheet feeder until its sides latch on the fixed bolts in the printer. The sheet feeder is now installed successfully. To remove the sheet feeder, use one hand to hold the printer and the other hand to pull and unlatch the sheet feeder.
Tally Dascom 1325 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch “A”, located to the right side of the printer, is in the OFF position.
Tally Dascom 1325 Installing the Windows Driver (Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen on the right. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click “Next” to continue. 3. Select the desired printer model as shown on the right. Click “Next” to continue.
Tally Dascom 1325 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 5. Click “Finish” to start the installation process. 6.
Tally Dascom 1325 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right.
Tally Dascom 1325 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~7 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled.
Tally Dascom 1325 There are 2 paper feed modes: friction feed and tractor feed. Friction Feed Handling 1. Move the paper-feed lever forward to “ ” for friction feed mode. 2. Adjust the print gap lever if necessary. 3. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. 4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen. 5.
Tally Dascom 1325 4 Control Panel Operation There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are described below. LED Indicators “Power/Paper Out” LED: On: Power on Flashing: Paper out Flashing + buzzer: Paper jam “Online” LED: On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. “Front Exit” LED: On: After printing, single sheet paper exits at the front.
Tally Dascom 1325 Control Panel Keys “Online” Key: This key switches the printer between online and offline states. Printing is stopped when the printer is switched to offline state. When printer is switched to online state again, printing will resume. “Load/Eject” Key: When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper (continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting print position.
Tally Dascom 1325 Panel Operation There are 3 states of operation: Online, Offline and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, and switch to Offline state. In the Offline state, the keys provide the following functions: Select Slip paper profile, select paper exit direction, Load/Eject, switch to Online state, micro feed, clear buffer and restore factory defaults.
Tally Dascom 1325 Online State Function Name Switch Operation LED Function Description This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts Tear Off {S1} - on the next TOF by: pressing S1 once, or receiving print data from the host. LF {S2} - Feeds a line with every press of S2.
Tally Dascom 1325 Offline State Function Name Slip Switch Operation [S1] LED L2 Function Description Press and hold this key until printer beeps twice to activate the Slip profile mode. L2 will turn on. Press and hold this key until printer beeps twice to exit the Slip profile mode. L2 will turn off. Exit Dir {S2} L3 This is valid for single sheet mode only. It controls the exit direction of the friction sheet paper.
Tally Dascom 1325 Power-On State Function Switch Name Operation Menu Setup / EDS Slip Setup LED - [S1] Function Description Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) [S2] - Configures the Slip paper profile such as top and left margins. Refer to Slip Setup section below for details.
Tally Dascom 1325 Self Test / [S4] Status Page Service Menu Adjust Page Margins Restore Factory Defaults [S1]+[S2] - Prints the printer settings and self-test pattern. Vertical Alignment, Change Pin Function and Endless Self Test [S3]+[S4] Includes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position.
Tally Dascom 1325 Slip Setup Slip media refers customized forms specific to each application. Each slip may have its own unique top margin or left margin. This is called the slip profile. The Slip setting provides a convenient way to set the printer top and left margin settings to the slip profile at the press of a panel key without the need to manually change the top and left margins, whenever you want to do your slip printing.
Tally Dascom 1325 5. Printer Setting Changes In order to meet individual print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off.
Tally Dascom 1325 When printing 180x180 DPI Graphic Speed graphics: Normal – prints in 180x180 DPI, Fast – prints in Normal, Fast, Ultra 90x180 DPI, Ultra – prints in 60x180 DPI. IBM Set 1/2 Selects the IBM character Set 1, Set 2 set. 1: Normal; 2: Extended USA, France, Germany, UK, Denmark, Sweden, Italy, Int'l Char Set Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal 14+1 international character set selections 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7.
Tally Dascom 1325 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 Character Table Character table type Graphic Table, Italic Table selection Page Setup Page Setup Line Per Inch Valid Settings Function Sets the line spacing 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" Fanfold Form Length 6",7",8", 8.
Tally Dascom 1325 Interface Setup Interface Valid Settings Setup Function For multi-host connection. Auto: First come first served; Interface Auto, Parallel, USB Parallel/USB: Serves the designated host only. I-PRIME Yes, No Yes: Host I-Prime signal resets the printer. Auto IF Delay Determines the waiting time before receiving data from another 10s, 30s interface.
Tally Dascom 1325 German (Deutsch) System Setup Valid Settings Emulation ESC/P2, IBM 2390 Plus Auto CR (IBM) Ja, Nein Auto LF Ja, Nein Druck Dir Bi-Dir, Uni-Dir, Auto Top Druck Dir Bi-Dir, Uni-Dir Anschlag Normal, Stark IBM AGM Ja, Nein Druck Setup Valid Settings Font (Andere) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Zeichenteilung 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Null 0,Ø HS-Draft An, Aus Graphikgeschw.
Tally Dascom 1325 Auto IF Delay 10s, 30s RAM Nutzung Ladbarer Font, Puffer Valid Settings Erweitertes Setup Auto Laden Manuell, 0.5s, 1s, 1.
Tally Dascom 1325 бумаги Отступ снизу для непрерывной бумаги Длина формы для отдельных листов 0/60"…10/60"...30/60" 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Отступ сверху для отдельных листов 0/60" … 10/60"…99/60" Отступ снизу для отдельных листов 0/60"…10/60"...30/60" Рулонная бумага Да, Нет Пропуск перфорации Да, Нет Авто прогон Ручной, 0.
Tally Dascom 1325 Menù Stampa Valid Settings Fonte (Altre) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Spaziatura 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0,Ø HS-Bozza Si, No Veloc. Grafica Normale, Veloce, Ultra IBM Set 1/2 Set 1, Set 2 Set Carat. Int. USA, France, Germany, UK, Denmark, Sweden, Italy, Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal Code Page CP 437, CP 857… Tab.Carattere Tab.
Tally Dascom 1325 Cicalino Si, No French (Français) Setup système Valid Settings Emulation ESC/P2, IBM 2390 Plus RC-Auto (IBM) Oui, Non SL-Auto Oui, Non Dir Impr. Bidir, Unidir, Auto Sup. Dir Impr. Bidir, Unidir Frappe Normal, Forte IBM AGM Oui, Non Valid Settings Setup impression Polices (Autres) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Densités caract. 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zéro 0,Ø HS-Draft Oui, Non Vitesse graphiq.
Tally Dascom 1325 Auto IF Delay 10s, 30s Utilisation RAM User Font, Buffer Setup élargi Valid Settings Chargem. Autom. Manuel, 0.5s, 1s, 1.5s, 2s Prévention bourrage Qui, Non Détec.fin de pap Qui, Non Long.formul.Strg Software, Ignorer Densi.caract.
Tally Dascom 1325 Margen Inf. Pap.Cont. Tamaño Hojas Sueltas 0/60"…10/60"...30/60" 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margen Sup. Folios 0/60" … 10/60"…99/60" Margen Inf. Folios 0/60"…10/60"...30/60" Rollo de Papel Si, No Salto perforación Si, No Mover a PosiciónCorte Manual, 0.
Tally Dascom 1325 Sıfır 0,Ø Yük.Hız-Taslak On, Off Grafik Hızı Normal, Hızlı, Ultra IBM Karakter Seti 1/2 Set 1, Set 2 Uluslararası Kar. Seti USA, France, Germany, UK, Denmark, Sweden, Italy, Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal Kod Sayfası CP 437, CP 857… Karakter Tablosu Grafik Tablosu, İtalik Sayfa Düzeni Ayarı Valid Settings İnç başına satır 1, 2, 3, 4, 5, 6, 7, 8 Sürekli-kağıt Form Uzunluğu 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.
Tally Dascom 1325 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure: 1. Enter the Service Menu by holding down the【Tear/Off】and【LF/FF】keys while powering up. 2. Load paper. 3. The printer will print as follows: Service Menu 【LF/FF】= OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit Current Setting：Vertical Alignment 4. Press【LF/FF】key to select the current setting.
Tally Dascom 1325 printed above. 7. Once the setting which gives the best alignment is found, press 【Online】 key to exit current level. Printer will print “Save settings? Yes”. Press 【LF/FF】 key to save setting. Press 【Online】 key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail.
Tally Dascom 1325 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure: 1.
Tally Dascom 1325 【Load/Eject】key: Increase 0.5mm 5. Press 【LF/FF】 key, printer will print “Save settings？Yes”. Press 【Load/Eject】 key to choose Yes or No，then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure: 1.
Tally Dascom 1325 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter.
Tally Dascom 1325 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob.
Tally Dascom 1325 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution • Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly.
Tally Dascom 1325 Paper Handling Problems and Solutions Problem Solution • Make sure that the paper select lever located on the top right of Paper cannot be loaded or fed. the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path.
Tally Dascom 1325 If paper is loaded and the paper select lever is moved to the Paper select lever error incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position. Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner.
Tally Dascom 1325 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.
Tally Dascom 1325 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.
Tally Dascom 1325 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Speed Font Matrix Print Head Graphics Pitch HS Draft Draft LQ 10 CPI 375/80H 250/120H 83/360H 12 CPI 300/120H 300/120H 100/360H 15 CPI 375/120H 375/120H 125/360H 17.
Tally Dascom 1325 Bitmap Fonts: 1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI 6. OCR-B 10, 12, 17, 20 CPI Built-In Fonts 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI 1. EAN-13 2.
Tally Dascom 1325 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp Code Pages 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8.
Tally Dascom 1325 Line Spacing 1/6", 1/8", n/60", n/180", n/360" Fanfold Paper Cut Sheet Single ply Paper Specifications Multi-part Width: 55mm～297mm Width: 55mm～297mm (2.2"～11.7"） （2.2"～11.7"） Length: Length: 139.7mm min (5.5" min) 55mm～363.2mm Paper Specifications （2.2"～14.3"） Weight: 52～100g/㎡ Weight: 52～100 g/㎡ Thickness: Thickness: 0.065～0.14mm 0.065～0.14mm (0.0026"～0.0055”) (0.0026"～0.0055") Weight: 40～58g/㎡ Thickness: 0.
Tally Dascom 1325 Temperature Operating: Ambient Conditions Humidity +5 to +40 °C. Stand-by: -20 to +55 °C Operating: 10 to 90%RH (No condensation) Stand-by: 10 to 85%RH (No condensation) Dimensions 404 mm (W) x 322 mm (D) x 203 mm (H) Weight 5 kg Power Supply Unit type: Switching mode power supply Power cord: Detachable Voltage rating: AC 230V (180V~264V)/50Hz to 60Hz Stand by: ESD: Less than 5.
Tally Dascom 1325 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission 1 STROBE ¯¯¯¯¯¯ Printer Computer 2~9 DATA Printer Computer 10 ACK ¯¯¯ Printer Computer 11 BUSY Printer Computer 12 PE Printer Computer 13 SELECT Printer Computer 14 AFXT ¯¯¯¯ Printer Computer 15 Unused Unused 16 GND Printer Computer 17 F-GND Printer Computer 18 +5V Printer Computer 19~30 GND Printer Computer 31 ¯¯¯¯ INIT Print
Tally Dascom 1325 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 49
Tally Dascom 1325 IBM Character Set 1 IBM Character Set 2 50
Tally Dascom 1325 International character sets International Character Set Commands Country USA Command ＜ESC＞“R”CHR＄（0） France ＜ESC＞“R”CHR＄（1） Germany ＜ESC＞“R”CHR＄（2） UK ＜ESC＞“R”CHR＄（3） Denmark1 ＜ESC＞“R”CHR＄（4） Sweden ＜ESC＞“R”CHR＄（5） Italy ＜ESC＞“R”CHR＄（6） Spain1 ＜ESC＞“R”CHR＄（7） Japan ＜ESC＞“R”CHR＄（8） Norway ＜ESC＞“R”CHR＄（9） Denmark2 ＜ESC＞“R”CHR＄（10） Spain2 ＜ESC＞“R”CHR＄（11） Lat America ＜ESC＞“R”CHR＄（12） Korea ＜ESC＞“R”CHR＄（13） Legal ＜ESC＞“R”CHR＄（64） 51
Tally Dascom 1325 Character Tables Italic 52
Tally Dascom 1325 Graphic 1 Graphic 2 53
Tally Dascom 1325 Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdo 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab.
Tally Dascom 1325 Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.
Tally Dascom 1325 Code Page Tables CP 437 (US) CP 737 Greek 56
Tally Dascom 1325 CP 850 (Multilingual) CP 851 57
Tally Dascom 1325 CP 852 (Eastern Europe) CP 857 (Turkish) 58
Tally Dascom 1325 CP 858 CP 860 (Portugal) 59
Tally Dascom 1325 CP 861 (Iceland) CP 863 (French-Canadian) 60
Tally Dascom 1325 CP 864 Arabic CP 864 Arabic Extended 61
Tally Dascom 1325 CP 865 (Norway) CP 866 (Cyrillic) 62
Tally Dascom 1325 CP 866 Bulgaria CP 1250 Win Latin 2 63
Tally Dascom 1325 CP 1251 Win Cyrillic CP 1252 Win Latin 1 64
Tally Dascom 1325 CP 1253 Win Greek CP 1254 Win Turkish 65
Tally Dascom 1325 8859-1 Latin 1 8859-1 Latin 1 (SAP) 66
Tally Dascom 1325 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 67
Tally Dascom 1325 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 68
Tally Dascom 1325 ISO 8859-15 Euro (Code Page 923) BRASCII 69
Tally Dascom 1325 Abicomp Roman 8 70
Tally Dascom 1325 Coax/Twinax (Hebrew) New-437 (Hebrew) 71
Tally Dascom 1325 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 72
Tally Dascom 1325 Flarro 863 (Hebrew) 865 Hebrew 73
Tally Dascom 1325 CP 1257 866 Ukraine 74
Tally Dascom 1325 866 Kazakhstan Kamenicky 75
Tally Dascom 1325 Mazovia CP 775 76
Tally Dascom 1325 CRO-ASCII Arabic Farsi 77
Tally Dascom 1325 Arabic Urdo Greek DEC 78
Tally Dascom 1325 Greek ELOT 928 79
Tally Dascom 1325 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC .
Tally Dascom 1325 ESC : ESC ＜ ESC > ESC = ESC # ESC ？n m ESC @ ESC ＼n1 n2 ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M ESC N n ESC O ESC P ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 … ESC Z n1 n2 … ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Copy ROM to RAM Unidirectional mode(1 line) Set MSB
Tally Dascom 1325 IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one l
Tally Dascom 1325 ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m S
Tally Dascom 1325 84
DASCOM REPRESENTATIVES GERMANY UNITED KINGDOM RUSSIA and CIS DASCOM Europe GmbH DASCOM GB Ltd DASCOM Europe GmbH Heuweg 3 ViewPoint, Basing View, Representation Moscow D-89079 Ulm Basingstoke, Hampshire Leninsky Prospekt 95a, Office 322 Deutschland RG21 4RG, England 119313 Moscow, Russian Federation Tel.: +49 (0) 731 2075 0 Phone: +44 (0) 1256 481481 Phone: +7 (495) 984 70 65 Fax: +49 (0) 731 2075 100 Fax: +44 (0) 1256 481400 Fax: +7 (495) 984 56 42 www.dascom.com www.dascom.com www.
