Tally Dascom 2610 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operator’s Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 2610 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 2610 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 2610 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 2610 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 2610 Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. Данная инструкция должна быть всегда доступна каждому пользователю. Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.
Tally Dascom 2610 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. Consulte sempre um técnico qualificado para executar uma reparação . Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 2610 Önemli Güv enlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güv enlik talimatlarını bütünüyle dikkatle okuyun. Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiyebir uzman servis-teknisyenine haber verin. Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Tally Dascom 2610 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 2610 TABLE OF CONTENTS 1 2 3 4 5 6 Printer at a glance .................................................................................................................................. 1 1.1 Unpacking the printer ..................................................................................................................... 1 1.2 Remove transport locks ................................................................................................................. 1 1.
Tally Dascom 2610 6.1.5 Network Interface Status ................................................................................................... 48 IP Configuration ........................................................................................................................... 49 6.2.1 Network IP Configuration ................................................................................................... 49 6.2.2 Assigning the IP Address ...................................................
Tally Dascom 2610 9.3.1 Standard Tractor (Front, Rear and Pull position) – narrow and wide versions ................113 9.3.2 Front Feed / Manual Insertion – Narrow and wide versions ............................................114 9.3.3 Paper Weights ..................................................................................................................114 10 Maintenance ................................................................................................................................
Tally Dascom 2610 1 Printer at a glance 1.1 Unpacking the printer 1.2 Remove transport locks Besides this manual, the package will contain: a power cord, a ribbon cartridge, a tractor, a CD and 6 pieces of U-wire paper support.
Tally Dascom 2610 1.
Tally Dascom 2610 For Fanfold For Cut Sheets 3
Tally Dascom 2610 1.
Tally Dascom 2610 2 Installation 2.1 Placing the printer Place the printer on a solid, flat, stable surface such that the printer sits firmly and cannot move. Select an environment with sufficient ventilation, easy access to the control panel and paper input areas as well as the printed output. When selecting the printer location, observe the following additional requirements: 1) Never place the printer near to any flammable gas or explosive substances. 2) Do not expose the printer to direct sunlight.
Tally Dascom 2610 2.2.1 Parallel interface (IEEE 1284) Make sure that the printer and the computer are switched off and connect the parallel cable between the printer and the computer. Lock the connector with the 2 clips on the printer interface connector; tighten up the 2 screws on the other end connecting to the computer. 2.2.2 USB 2.0 (Full Speed) Plug in the USB cable to the printer and the computer. 2.2.
Tally Dascom 2610 2.2.4 Serial Interface (RS-232C) as option 2.2.5 Connecting the power Plug in the power cord to the printer power socket as shown in the diagram. Connect the printer to the correct voltage power source. The socket-outlet shall be installed near the equipment and shall be easily accessible. 2.2.6 Switch on the printer Switch on the printer as shown in the diagram.
Tally Dascom 2610 2.3 Installing the ribbon cartridge 1) Switch off the power. 2) Unfold the top cover and follow the steps 1.2.3.4 in the below picture.
Tally Dascom 2610 4) Insert the ribbon cartridge till it is tightly locked in position. 5) Insert the ribbon fabric in between the print head and ribbon mask. 6) Turn the knob on the left hand side several times in order to tighten the fabric, and the fabric will slide downwards into the correct position between printhead and ribbon mask after the moving. 7) Restore the upper friction assembly to its original position. Print head may be hot, please move the printhead by moving the carriage.
Tally Dascom 2610 3 Installing the paper The printer can handle either single sheets or continuous forms. The printer is able to print up to 5 copies (original plus 5). To ensure the print quality and protect the print head, set a proper print gap by the gap lever (see 3.1) for the form thickness and do not load folded, damaged, wrinkled, or curled paper. 3.1 Adjusting the print gap for various form thicknesses The print gap lever is on the left side of the printer inside the top cover.
Tally Dascom 2610 3.2 Paper path introduction 3.2.1 Cut sheet paper handling (front friction only) 1) Place the paper path lever to the cut sheet position. 2) Unlock the front cover with the latch to unfold the cut sheet support. 3) Adjust the gap lever if necessary; see 3.1. 4) It is recommended to align the left paper guide exactly to the mark > I <. This marks the left edge of the stationery. Slide the right guide to the position of the right edge of the stationery.
Tally Dascom 2610 3.2.2 Fanfold paper handling 3.2.2.1 Front push tractors for fanfold 1) Close the front cover if previously opened. Switch the paper path lever to one of the desired tractor positions. 2) Move the paper path lever to the desired position. 3) Adjust the head gap lever if necessary. 4) Open the front cover by tilting the cover from bottom to the top, and make sure it’s locked in place (see below pictures). Lock the front cover in the way that is shown in the pictures.
Tally Dascom 2610 5) If you do not need to adjust the left margin go to the next step. Open the right and left tractor flaps, insert fanfold paper into the left-hand tractor, and make sure that at least three paper transport holes are positioned on the tractor pins, close the tractor flap, open the latch lever and align the tractor so that the first printing position on the paper matches the IIIIXIIII mark on the printer housing, then lock the lever again.
Tally Dascom 2610 3.2.2.
Tally Dascom 2610 3.2.2.3 Top pull tractors for fanfold For the steps ② and ③, please refer to the 2.
Tally Dascom 2610 3.2.3 Top-Of-Form adjustment For pull tractor (PullTr), follow the steps below to adjust the first print position: 1) Remove Paper from printer. 2) Power on the printer. 3) Lift the Top Cover so you can see the transparent ribbon guide in front of the print head. 4) Install the paper into the pull tractor. 5) Move the paper with the hand wheel so the perforation of the fanfold paper lies exactly at the top of the transparent ribbon guide. 6) Close the Top Cover.
Tally Dascom 2610 4 Control Panel Operation General functions for the keys are clearly designated on the Panel label. Some other special settings need pressing multiple switches simultaneously or holding some keys when powering on the printer. This Chapter will describe the functions of the keys and display (LEDs or LCD) on the Panel. 4.1 Operation of the LED Panel 4.1.
Tally Dascom 2610 ◆ Keys 1)【Online】 a) Every press on this switch toggles the status between Online and Offline. When the printer is Online, it receives data from the host; while it is Offline, it stops the printing and signals the host to stop sending data. b) Press the key【Online】for the below operations: Before and after special setup: Most of the special setup requires Offline operation.
Tally Dascom 2610 4.1.2 Online Operations Function Name Offline Switch Operation {S1} Load/Eject {S2} Tear Off {S4} Function Description LED light ON: Online; LED light OFF: Offline; Load: Load the paper from active paper path to first print position. Eject: Either park the fanfold paper or eject cut sheet paper. This is valid for tractor mode only. It feeds the form to the tear-off position.
Tally Dascom 2610 4.1.3 Offline Operations Function Name Online Load/Eject Switch Operation {S1} {S2} Speed LF/FF Setup Menu Clear Buffer and Reset {S3} {S4} [S2] +[S3] [S1] +[S2] Function Description. LED light ON: Online; LED light OFF: Offline. Load: Load the paper from active paper path to first print position. Eject: Either park the fanfold paper or eject cut sheet paper. Toggle Between HS-Draft /Draft or NLQ/LQ. Brief press: Linefeed, Longer hold: Formfeed. Enter Printer Setup Menu.
Tally Dascom 2610 Detailed descriptions of the above functions: ◆ Speed If LQ font is currently set in the configuration, lighting up of the【Speed】LED forces NLQ font printouts; turning off【Speed】indicates LQ printouts. If Draft is currently set in the configuration, lighting up of the【Speed】LED forces HS Draft printouts; turning off【Speed】indicates Draft printouts. ◆ Setup Menu See Chapter 5 for details.
Tally Dascom 2610 4.1.4 Power-On Operations Function Name Technical Setup Switch Operation [S1] Menu Unlock [S2]+[S3] Status Page [S4] Load Defaults [S1]+[S2]+ [S3]+[S4] Function Description Start Technical Setup / Advanced Menu (This also includes Self Test Mode). Override Menu Lock Function if Menu is locked. Print Status Page. Load Default Settings. Detail descriptions of the above functions: ◆ Technical Setup See Chapter 5 for details.
Tally Dascom 2610 4.2 Operation of the LCD Panel ◆ The Online mode is the printer’s normal operating mode. Data from your computer can be received and printed. ◆ In the Offline mode the link between printer and computer is interrupted, i.e. no data can be received and printed. ◆ In the Setup mode you can either select the printer menu or carry out the quick-switch function.
Tally Dascom 2610 4.2.2 Online mode After switching on, the printer is automatically set to online mode. Only in this mode can it receive data from the computer. ■ Online key: Toggle between Online and Offline mode. ■ Tear key (4): Activates the tear function when fanfold paper is loaded. If Load is displayed above this key, no paper is loaded in the printer or the paper is in park position. In this case the display switches between Online and Park Position.
Tally Dascom 2610 4.2.4 Setup mode In this mode, the following settings are available: ■ Setup key: Sets the printer to setup mode, in which the following settings can be selected. ■ Menu key (1): Other menu settings. Access may be disabled by menu settings (see note below). ■ Adjust key (2): Sets the Tear position and first printing line (TOF). If you have the PullTr (Pull - Tractor) selected Adjust is not available. ■ Char key (4): Sets the font and the number of characters per inch temporarily.
Tally Dascom 2610 5 Setting parameters for the printer (Programming via the control panel) Apart from being able to control your printer via the applications software you use, you can also program the printer directly. There are two programming options you can use: ◆ Programming via the control panel. ◆ Programming via the interface using Escape sequences or control codes. Settings made by escape sequences have priority over settings made in menu mode; therefore they will override these.
Tally Dascom 2610 increment or decrement the TOF value. After adjustment, press Key 1 (Set) to save the change. Set the Tear position in the same way. Move the perforation of the stationery exacly to the Tear Edge. 5.1.2 Select a font Below example demonstrates how to select Roman LQ font type under the Char setting. 1) First, load fanfold paper to one of the tractors and bring the printer Offline. Pressing 【Load/Eject】and【Speed】keys simultaneously activates the parameters setting operation.
Tally Dascom 2610 5.1.3 Settings within Menu Below example demonstrates how to select an Emulation within the Menu. 1) First load fanfold paper to one of the tractor and bring the printer Offline. Pressing 【Load/Eject】and【Speed】keys simultaneously activates the parameters setting operation. The printer prints out 2 lines of key assignments valid for the parameter setting operation. Key 1 Key 2 Key 3 Key 4 Menu Adjust Char 2) Press【Online】(i.e. Key 1) to get into Menu operation.
Tally Dascom 2610 5.2 Setting the parameters through the LCD Panel This chapter describes the handling of the operator’s panel with optional display. 5.2.1 Enabling access to menu mode The menu can be locked by default to protect it from accidental or unauthorized access. Proceed as follows to release this lock temporarily. 1) Switch off the printer for approx. 5 seconds. 2) Switch the printer on again keeping the Setup key pressed.
Tally Dascom 2610 5.2.2 Menu configurations Every printer is shipped with factory default settings. Basic settings such as emulation, character size, form length etc., which many applications make use of, are set. At the end of this chapter you will find a menu printout which shows you the printer’s default settings. Your printer allows you to set and use five independent menu configurations.
Tally Dascom 2610 Menu Printout 31
Tally Dascom 2610 5.2.3 Menu handling You can navigate in the current menu using the four function and selection keys arranged below the LC display field. Each function and parameter displayed in the LCD is executed or selected by the corresponding key below, respectively. Usually two parameter groups are combined at one level. In the following example, these are the LPI and Skip parameter groups.
Tally Dascom 2610 5.2.4 Selecting the LC display language This section describes how to make settings in the menu, using the selection of the national language as an example. In this user guide all LC display messages are shown in English language. Your printer offers also the possibility to show the display messages in German, French, Italian, Spanish or Turkish language. This example shows how to change from the English language to the German language.
Tally Dascom 2610 5.3 Menu structure The menu structure of your printer may be slightly different from the example shown here, depending on the printer software. ←Next MENU Back→ Print Menu LeftMrg Reset Quietm FFmode Font CPI Barcode Barmode LPI Skip Eject Width ESCChar Emulate Paper Auto Tear Bidir I/O Serial 1) CG-Tab Single Tr Front Tr Rear Pull Tr Interf. Buffer Baud Format1) MenLock Language Protocol1) DTR Auto-CR Auto-LF Country Sl.
Tally Dascom 2610 5.4 Full list parameters setting In order to meet individual requirements of printer functionality, users may modify the printer configuration settings accordingly as follows: start by pressing [Load/Eject] + [Speed] in offline mode. The printer will enter Main Menu settings setup mode. Follow the instructions printed on how to do the required setting changes. When a new setting is saved, it becomes effective, even when printer is power cycled. 5.4.
Tally Dascom 2610 Prestige NLQ Prestige LQ Script NLQ Script LQ OCR-B NLQ OCR-B LQ OCR-A NLQ OCR-A LQ Orator NLQ Courier I NLQ Courier I LQ Orator LQ Souvenir NLQ Courier I PS NLQ Gothic NLQ Souvenir LQ CPI LPI Skip Courier I PS LQ Gothic LQ 10 CPI, 12 CPI, 15 CPI, 17.1 CPI, 20 Sets the characters per inch (character pitch). The higher parameter the smaller CPI, 5 CPI, 6 CPI, 7.5 CPI, 8.6 CPI. character spacing. 6 LPI, 8 LPI, 12 LPI, 2 LPI, 3 LPI, 4 LPI.
Tally Dascom 2610 Format 8Bit No 1Stop 8Bit No 2Stop 8Bit Even 1Stop This parameter serves to define the number of data bits, the parity check for received data bytes and the number of stop bits per data byte. 8Bit Odd 1Stop 8Bit Mark 1Stop 8Bit Spc 1Stop 7Bit No 2Stop 7Bit Even 1Stop 7Bit Odd 1Stop 7Bit Odd 2Stop 7Bit Mark 1Stop 7Bit Spc 1Stop 7Bit Mark 2Stop 7Bit Spc 2Stop Protocol XON/XOFF RobustXON/XOFF ENQ/STX This parameter serves to select the type of protocol, i.e.
Tally Dascom 2610 ETH-INT Gateway Octets 1-4 0 to 255 Input of the IP address of the printer This menu level offers the possibility to set the IP address, which is divided into four digit groups (octet 1 to 4). Input of the Gateway address of the printer. Octets 1-4 0 to 255 Input of the Subnet mask address of the printer. IP-Addr Subnet Octets 1-4 0 to 255 IP Get M DHCP Static Banner BOOTP Selects the way of administrating the IP address.
Tally Dascom 2610 Coax/Twinax Table 437 New-437 Table 737 775 Baltic Table 850 New-Dig 850 Table 851 Table 852 Table 857 Table 858 Table 860 Table 861 Old-Code 860 Table 863 Flarro 863 Table 865 865 Hebrew Table 866 866 Bulgaria 866 Ukraine 866 Kazakhst Kamenicky Mazovia Siemens Turk DEC Turkish Table 1250 Table 1251 Table 1252 Table 1253 Table 1254 Table 1257 Sl.Zero Sl.Zero=Off AutoCR On Off AutoLF Off On Menlock Off Menu Language English Spanish Paper Single Sl.
Tally Dascom 2610 Formlen Lines =6 – 132 Default 6LPI = 66 Single:3—22 inches TrFront、TrRear 、 PullTr：1—22 inches Standard Sets the form length via line formats. Please note that the adjustment in Lines depends on the selected LPI. For example 8 LPI at a selected line number of 96 lines results in a form length of 12 inches (96lines/[8lines/inch]) = 12 inches. The selectable range is between 3 and 21 inches, i.e. for 2 LPI from 6 to 42 lines and for 12 LPI from 24 to 262 lines.
Tally Dascom 2610 Width Width=13.6Inch Selects the line length in inches. With the setting of 8 Inch, the printer operates like a printer with a width of only 8 inches. Width=8Inch Width=13.2Inch Eject Eject=Top This is valid for single sheet mode only. It controls the exit direction of the friction sheet paper. With this function selected it is possible to print different barcodes and LCP (Large Character Printing). Allows printing of normal characters on the left and right of the barcode.
Tally Dascom 2610 5.4.2 Advanced Menu Advanced Valid Settings Menu Function ASCII80 8 inch wide print of test pattern ASCII136 13.6 inch wide print of test pattern (only 2610) H-Dump Hvy Form With the interface test (Hex-Dump/H-Dump) you can test data transmission from the computer to the printer. During this test, the data from the computer is printed out in two columns. The text in the left column is printed in hexadecimal format and in the right column in ASCII format.
Tally Dascom 2610 Physlm Widthcon CX-bid menu item “Paphand” (Paper Handling). This setting tells the printer logic the width of the installed paper and is valid for all paper ways. By default this parameter is maximum width. 2600: 80 Characters (80/10”) 2610: 136 Characters (136/10”) The value can be changed in 1/10” in a range between 20 and 136 (80). Permanent (physical) setting of the left margin. This parameter cannot be changed by emulation dependent margin settings.
Tally Dascom 2610 Sound Sound=On When Sound=On, a beep is generated every second to notify that paper is empty. Pap.back=normal is the standard for normal paper. Pap.back=dark can be set to process paper with a grey back. Paper with a completely black back side cannot be used if the ink is carbon-based. However, the printer can handle aniline- based black paper (undefined colors). If APW=On, the printer is in the standard mode and truncates all data located beyond the right-hand and left-hand paper edge.
Tally Dascom 2610 SerialN AssetN GrSpeed a width of 13 mm or more as the right-hand paper edge. If the sensor does not detect any black area, the maximum possible printing width is used as the printable area. With the SerialN function you have the possibility to change the 12 digit serial number of the printer. The number can be written with any ASCII character between hex 20 and hex 7E. factory set LED Panel: The Serial Number cannot be set via menu instead you need to use the WebPanel.
Tally Dascom 2610 5.5 Display messages If the printer detects an internal fault or user error or if it expects you to do something, a message will appear in the LC display (LED’s display message reference below table 5.6.1). It also displays the status during an operation (e.g. Initializing). Below you will find a list of messages with brief descriptions of each message. 5.5.1 Messages LED Panel LED Messages Error/Power ON Online Tractor Speed Pap.Out Power/Err.
Tally Dascom 2610 5.5.2 Messages LCD Panel LCD Messages Meaning Initializing The printer cannot eject the paper/advance it to park position. Internal hardware error, contact your dealer or service technician. The print head is too hot. The printer will reduce its print speed. This message appears during the printer’s initializing phase after switching on the printer. Load error The printer fails to load the paper.
Tally Dascom 2610 6 Web Panel and Internal Ethernet Interface 6.1 Summary 6.1.1 Introduction It is assumed you have the following: ◆ A working knowledge of your network system and related utilities. ◆ Access to the supervisor or administrator account as a network administrator. 6.1.2 Supported Environments The built-in network interface supports the following platforms and protocols: ◆ Microsoft® Windows® NT 4.
Tally Dascom 2610 6.2 IP Configuration 6.2.1 Network IP Configuration The network interface of the printer requires an IP address. There are several ways to assign an IP address to the printer: ◆ DHCP (A Dynamic Host Configuration Protocol server assigned IP address.) ◆ Static (An IP address obtained from your network administrator added to the printer manually.) ◆ BOOTP (Bootstrap Protocol server assigned IP address.) 6.2.2 Assigning the IP Address If the printer menu is locked, please see the 4.2.5. 1.
Tally Dascom 2610 2. Static assignment using the operator panel: ◆ Press < Setup >, then < Menu >. ◆ Press < Next > until the I/O selection appears. Select < I/O >. ◆ Press < Next > until the ETH-INT selection appears. Select < ETH-INT >, then< IP Addr > ◆ Enter the value for Octet 1by pressing < OCTET 1 >. Use the forward and backward arrows to increment/decrement the number. When finished with each entry press < Set > which will set the currently displayed value.
Tally Dascom 2610 6.3 WebPanel 6.3.1 Introduction WebPanel is an intuitive browser interface that allows you to remotely manage your network attached printer. From WebPanel, you can do virtually everything you can do from the printer's control panel. In addition, WebPanel provides full access to all of the TallyCom networking features. Before using WebPanel, you must configure your printer with an IP address, using one of the three methods discussed in the Assigning the IP Address section above.
Tally Dascom 2610 6.3.3 Access to WebPanel & Control Tool 6.3.3.1 Access to WebPanel Once an IP address has been set up, you can access WebPanel by typing the printer's IP address into your browser address box. The current status of your printer is displayed on the right hand side of the screen. This is refreshed every 20 seconds, whenever you refresh the page or click Printer Status. The left side allows you to query the printer, configure it and access network options.
Tally Dascom 2610 6.3.3.2 Access to Config Tool The software interface for is shown as below. Click “Connect” to select the related interface. (After the Configuration Tool is connected, the operation interface is similar to the WebPanel, thus the operation instruction not be started again). 6.3.4 Printer Status Selecting this option refreshes the status display.
Tally Dascom 2610 6.3.5 Printer Configuration Selecting this option allows you to configure specific parameters in the printer. When one of these menu options is selected, a new page will load showing the options which can be viewed or modified.
Tally Dascom 2610 Example 1 Changing the dropdown menu option. In this example, we are modifying the selected font to a different font. Select “Font”. A new page appears. Select the Font dropdown menu and choose the new font. Select “Send”. 1) Changes are not applied until “Send” is selected. 2) To reset the changed value to the prior value, select “Refresh” instead of “Send”. 3) To return to the prior page without applying the change, select “Back”.
Tally Dascom 2610 Example 2 Changing an entered value menu option. In this example, we are modifying the selected form length to a different form length. Select “Forms”. A new page appears: Select the Form Length field by highlighting the contents of the box and enter the new form length. The acceptable parameters are listed to the right of the field. Select “Send”. 1) Changes are not applied until “Send” is selected.
Tally Dascom 2610 6.3.6 Printer Actions Selecting the Printer Actions link will produce a page with a list of actions that can be performed on the printer.
Tally Dascom 2610 6.3.7 Load Configuration Loads the settings stored in a menu into the printer as the current settings. When the Load Configuration link is selected, the following page will be displayed: Select a menu and confirm your selection by selecting the Send button.
Tally Dascom 2610 6.3.8 Save Configuration You can save selected printer settings in up to 5 independent menus. When the Save Configuration link is selected, the following page will be displayed: Select a menu. Select send. 6.3.9 Retrieve Configuration From Printer Selecting this option will save all the printer settings of all menus in a file. Uploading this file to other printers will clone the printer menu settings to the other printer.
Tally Dascom 2610 6.3.10 Send Configuration to Printer Selecting this option will upload a Configuration File of another printer (see “Retrieve Configuration From Printer”). The complete configuration of this source printer will be transferred to your printer. To upload the configuration file, first click “Send Configuration To Printer”.
Tally Dascom 2610 Use the “Browse” button to find the file to upload. Once the file is selected, click on the “Send” button. It is important to note the warning on this page. There is some delay while the file is transmitted so it is important not to resend or click on the “Send” button until the process is complete.
Tally Dascom 2610 6.3.11 Report Selecting the report link will open up a separate browser window and a report of the printer settings will appear. This functionality is the same as pressing the “Print” option on the control panel of the printer. 6.3.12 Reset Printer This link does a hard reset of the printer, similar to cycling power. There is no user feedback as to success since the printer is rebooting.
Tally Dascom 2610 After following the directions on this page, select the “Continue“ link and the following page is displayed: Using the “Browse” button, find the firmware file to download. Once the file is selected, click on the “Send” button. It is important to note the warning on this page. There will be some delay while the file is transmitted so it is important NOT to resend or click on the “Send” button until the process is complete.
Tally Dascom 2610 If the process is successful, the printer will reboot and the following page will be displayed: Since the printer will reboot with successful completion of this action, the user will have to reconnect to the printer through the browser.
Tally Dascom 2610 6.3.15 TallyCom Status Selecting this link will replace the information in the Printer Status area with networking information on the printer. The Name, Contact and Location information is set up from the General link within the Advanced Configuration page.
Tally Dascom 2610 6.3.16 Advanced Configuration The Advanced Configuration page allows the user to set up and modify network connectivity information as well as setting up the password, email notification and logical printers. From this page it is also possible to Logout of TallyCom and restart TallyCom.
Tally Dascom 2610 6.3.17 General The General page sets up the timers and the labels for name, contact and location of the printer. The Print Server Name is by default and can be changed accordingly. This name used for entering into Name Server (DNS/DHCP).
Tally Dascom 2610 6.3.18 TCP/IP The TCP/IP Page allows the user to modify the existing TCP/IP information for the printer. After changing the particular parameters, it is necessary to restart TallyCom from the Advanced Configuration page. If the IP Address is changed and the Send button selected you will disconnect from the current session and will need to reconnect at the new IP Address.
Tally Dascom 2610 6.3.19 SNMP The SNMP page allows the user to set the Community Name and the Access.
Tally Dascom 2610 6.3.20 Password The Password page allows the user to set a password which would limit access to certain configuration and action links in WebPanel. The maximum number of characters for the password is 7. The default password is no password at all (“null“). However, “adm” is also acceptable as the default password to be compatible with the external TallyCom Ⅲ pocket NICs (Options), which use this as the default password.
Tally Dascom 2610 6.3.23 Email Notification With the email notification link the user will be able to set up and receive email notices for error and status conditions of the printer. Up to 4 email addresses can be set. The page looks like this: The user must set up the SMTP Mail Server as well as one or more users. The Reply address can be left as is unless there is reason to have to mail to the Reply address. To activate the mail notification: Select which notifications are to be sent out.
Tally Dascom 2610 The “Configure” link at the end of each line of notification options allows the user to set up the message information for the email as well as selecting other pertinent information to be added to the email. In addition, the timer can be set which determines when the email notification is sent out. The page looks like this: In this example, the Online message is set to “Printer is Online”, and information on Description, Location, and Printer Name will be added to the email.
Tally Dascom 2610 6.3.24 Logical Printers The logical printers page will add text or commands to the beginning and ending of print jobs. This is done by pre and post strings, defined in each of the logical printers. For entering binary data in these strings, the backslash character is used followed by 2 hexadecimal digits. Examples of this are \1b for an escape character, \0a for linefeed and \\ for backslash.
Tally Dascom 2610 When selecting one of the logical printers under the Description column, the following page is displayed: In this example if the Enable checkbox is checked, the pre-string of “Beginning to print job” followed by a CR/LF will print at the beginning of every job sent to this LPR Queue. At the end of the print job, the message “End of job” with a formfeed will print. Unchecking the Enable checkbox will not send the pre or post strings.
Tally Dascom 2610 6.3.26 Logout of TallyCom The Logout link disconnects the browser session from the printer. Clicking on the “Home” link reestablishes the connection. 6.3.27 Restart TallyCom Selecting this link will reboot the printer and disconnect the current printer connection. It is used to reset certain TCP/IP variables that were set in the General and TCP/IP pages. Once TallyCom has restarted, those new setting will take effect.
Tally Dascom 2610 6.3.28 Virtual Control Panel The Virtual Control Panel link is in the Printer Status area of the web page. This control panel is a visual representation of the actual control panel on the printer. It allows the user to remotely read and set panel information as if they were standing at the control panel. The functionality of the virtual panel is identical to the physical LCD panel.
Tally Dascom 2610 7 Addendum 7.
Tally Dascom 2610 IBM character set 1 IBM character set 2 78
Tally Dascom 2610 OCR-A character set 1 OCR-A character set 2 79
Tally Dascom 2610 OCR-B character set 1 OCR-B character set 2 80
Tally Dascom 2610 International Character Set Commands Country USA FRANCE GERMANY UK DENMARK 1 SWEDEN ITALY SPAIN 1 JAPAN NORWAY DENMARK 2 SPAIN 2 LATINAMERICA DENMARK/NORWAY CHINA Basic Command ＜ESC＞“R”CHR＄（0） ＜ESC＞“R”CHR＄（1） ＜ESC＞“R”CHR＄（2） ＜ESC＞“R”CHR＄（3） ＜ESC＞“R”CHR＄（4） ＜ESC＞“R”CHR＄（5） ＜ESC＞“R”CHR＄（6） ＜ESC＞“R”CHR＄（7） ＜ESC＞“R”CHR＄（8） ＜ESC＞“R”CHR＄（9） ＜ESC＞“R”CHR＄（10） ＜ESC＞“R”CHR＄（11） ＜ESC＞“R”CHR＄（12） ＜ESC＞“R”CHR＄（13） ＜ESC＞“R”CHR＄（16） International character sets： 81
Tally Dascom 2610 7.2 Control Codes Summary The following table shows sequences marked by a √ if they are available in the various emulations. The MTPL sequences can be used within all emulation modes. The corresponding sequences are marked by a *. If you want to learn more about control codes, we recommendto download the Programmer’s Application Manual from our internet support pages.
Tally Dascom 2610 IBM XL24 IBM AGM √ * * * √ √ * * * * MTPL Epson Epson LQ-2550 LQ-2170 Code Function * (.
Tally Dascom 2610 MTPL √ IBM XL24 * √ IBM AGM Epson Epson LQ-2550 LQ-2170 √ √ √ *<4> Set graphics print to 80 dpi √ √ √ *<40> Set graphics print to 360 dpi * √ * * √ √ √ * √ √ * * √ √ *MI>F Assign character set G2 - Underlining ON/OFF / Select vertical tab channels .
Tally Dascom 2610 IBM XL24 IBM AGM √ * * * √ * * * MTPL Epson Epson LQ-2550 LQ-2170 Code Function * [?7l Line overrun = Truncating data outside of the printing area * [?~ Change emulation √ √ [@ ... Set double height √ √ [\ ...
Tally Dascom 2610 IBM XL24 IBM AGM Epson Epson LQ-2550 LQ-2170 √ * * * √ √ * * * √ √ Code Function * [16m Font 6 Default: Script LQ * * [17m Font 7 Default: Prestige LQ * * * [18m Font 8 Default: OCR-B LQ * * * * [19m Font 9 Default: OCR-A LQ * * * * [1 g Clear vertical tab at current position √ √ * * * * [ 1 SP k Printout in Royal Mail customer barcode * * * * [1 SP L Set vertical spacing to 4 lpi √ √ * * * *
Tally Dascom 2610 IBM XL24 IBM AGM Epson Epson LQ-2550 LQ-2170 √ * * * √ √ * * * √ √ Code Function * [4m Underline ON * * [4 SP L Set vertical spacing to 8 lpi * * * [4w Set 10 cpi * * * * [4y Selecting NLQ printing quality at 10 cpi * * * * [4z Line density 8 lpi (= line spacing 1/8 inch) √ √ * * * * [5{ Select fanfold paper mode tractor 1 * * * * [6{ Select fanfold paper mode tractor 2 √ √ * * * * [50m Propor
Tally Dascom 2610 MTPL IBM XL24 IBM AGM Epson Epson LQ-2550 LQ-2170 Code Function √ [g <2> Set graphics print to 120 dpi √ √ [g <3> Set graphics print to 240 dpi √ [g <9> Set graphics print to 120 dpi [g <8> Set graphics print to 60 dpi √ √ [j Position paper back 1/180" √ √ * * * * [ f Set absolute horizontal and vertical position * * * * [+w Interface holding time n = 1 - 30 s √ √ * * * *
Tally Dascom 2610 MTPL √ IBM XL24 IBM AGM * * Epson Epson LQ-2550 LQ-2170 Code Function [ v Set vertical tab [\ Perform relative horizontal step √ \; Transparent mode for the characters following √ √ ^ Transparent mode for the character following _ Overline ON/OFF 0 Set line feed to 1/8 inch 1 Set line feed to 7/72 inch 2 Set line feed to 1/6 inch 2 Set line feed to n/72 inch 3 Set line feed to n/180 in
Tally Dascom 2610 MTPL IBM XL24 √ √ √ √ √ √ √ IBM AGM √ Epson Epson LQ-2550 LQ-2170 Code Function √ √ Double-wide printing ON √ √ √ √ Set character spacing t Select character set √ √ √ √ √ √ T Superscript or subscript OFF U Unidirectional print ON/OFF √ √ Un Unidirectional print ON/OFF √ √ √ W Continuous double width ON/OFF √ √ √ √ w Double height print ON/OFF x Set print quality (PQ) √ √ √ √
Tally Dascom 2610 7.2.1 PJL commands These PJL commands can be used with internal Ethernet interface as well as with external TallyCom III Pocket interface. This functionality may be activated via the parameter Jobcntl in the Advanced Menu.
Tally Dascom 2610 7.2.
Tally Dascom 2610 7.2.5 Royal Mail Customer barcode The Royal Mail Customer barcode is a special Mail type barcode. It is printed in character size. Numeric values from 0 to 9 and alpha- numeric values from A to Z are printable. After activating this barcode type, numeric characters from 0 (hex.30) to 9 (hex. 39) and alphanumeric values from A (hex. 41) to Z (hex. 5A) are interpreted as barcode figures. Lower cases from a (hex. 61) to z (hex. 7a) are automatically converted to capital characters.
Tally Dascom 2610 printer has the possibility of scaling standard size characters up to factor 99 by means of control sequences (LCP*). The Header sequence defines the parameters (e.g. height) once. This definition remains until the printer is switched off. The printable LCP* information is transmitted in an LCP “bracket” (SI). The following character sets (with national characters) are available.
Tally Dascom 2610 7.2.
Tally Dascom 2610 7.3 Interfaces Specifications Your matrix printer offers connectivity via a parallel interface, USB and Ethernet interface. Serial I/O RS232C interface is an option. This appendix informs you about the parallel Interface, USB, Ethernet interface and optional serial interface RS232C, and describes the communication between your computer and the printer. These interfaces are linked to form a called shared interface.
Tally Dascom 2610 7.3.1 Parallel I/O IEEE 1284 The bidirectional parallel interface offers the “nibble” mode of IEEE1284 interface. This enables installation in accordance with Windows “Plug & Play”. The standard parallel interface is able to transfer data at a speed of max. 30, 000 bytes per second. When the receiving buffer is full, the data input is blocked until the data buffer is empty. Connector assignment Connector no.
Tally Dascom 2610 7.3.2 Ethernet I/O 10/100 Mulitprotocol The Ethernet interface enables the printer to connect to local area networks. Its attributes are: Hardware Supported operating Systems Supported Protocols Designation of IP Address Configuration Status Management Setup LAN/Ethernet: RJ45, Ethernet 100BaseTX with 100 Mbps (IEEE802.3u), 10Base-T with 10 Mbps (IEEE802.
Tally Dascom 2610 Example of a Printer connected to a computer in an Network ◆ The assumed address space corresponds to the TCP/IP address, class C, 192.168.1.xxx. ◆ The subnet mask to be used is 255.255.255.0. ◆ The address of the router, or gateway, is 0.0.0.0, if not available. Example of several devices in an Ethernet 7.3.3 USB 2.0 I/O – Full Speed The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector.
Tally Dascom 2610 7.3.4 Optional Serial Interface RS232C Your printer’s serial interface supports the RS232C specification. The signals are received and transmitted by a 9 pin connector. Basically 3 lines are enough for exchanging information between computer and printer (one receive line, one send line, one line for common grounding).
Tally Dascom 2610 1) The serial cable length must not exceed 15 meters. 2) Make sure the “Interface Setup” selects serial interface and the settings are the same as PC communication port settings.
Tally Dascom 2610 Interface cable (serial interface) The cables used must be shielded. The cable shield must be connected to the connector shield on both ends. PC/AT（9 Pin） RxD 2 TxD 3 CTS 8 SG 5 DSR 6 DTR 4 Printer（9 Pin） 3 TxD 2 RxD 4 DTR/RDY 5 SG PC/AT（25 Pin） FG 1 TxD 2 RxD 3 CTS 5 SG 7 DSR 6 DTR 20 Printer（9 Pin） FG 2 RxD 3 TxD 4 DTR/RDY 5 SG It depends on the menu setting whether DTR or RDY (Ready) is active at Pin 4.
Tally Dascom 2610 Protocols ◆ Memory mode XON/XOFF The received characters are stored in a FIFO buffer (first in/first out). The characters are processed in this buffer. The buffer capacity can be adjusted from 0 to 128 Kb. If the buffer is full, the interface signals NOT READY (signal acknowledgement: Level 1, -12 V) and XOFF (hex. 13, dec. 19). This results in stopping the data transmission. When the FIFO buffer is empty again, the interface signals READY (level 0, +12 V) and XON (hex.11, dec. 17).
Tally Dascom 2610 ◆ ENQ/STX protocol In addition to this XON/XOFF message, the possibility exists of requesting a status byte from the printer using the ENQ code (hex. 05, dec. 5). The STX code (hex 02, dec. 2) is used to clear any error messages (parity error, buffer overflow). Status byte STX (hex02): ENQ (hex05): XON/XOF: HandThr.= ON: HandThr.
Tally Dascom 2610 8 Options and accessories The following options can be ordered for your printer. 8.1 Options Tractor Unit 2600 Name Second Tractor for push and pull position (rear, top and front installable). Part no. 99992 Tractor Unit 2610 Name Part no. Second Tractor for push and pull position (rear, top and front installable). 99993 Serial Interface 2600/2610 Name Part no.
Tally Dascom 2610 8.2 Consumables Ribbons Name Part no. Ribbon cassette monochrome black for narrow model 99061 Ribbon cassette monochrome black for wide model 99071 Refill Kits Name Part no. Refill Kit monochrome black fabric for narrow model, on demand 99002 Refill Kit monochrome black fabric for wide model, on demand 99072 8.3 Accessories Programming manuals The following programming manuals are available. You can download the manuals from our internet page. Name Part no.
Tally Dascom 2610 9 General Specifications 9.1 Printer Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Head Number of pins: 24 pins (2 x 12; staggered) Firing frequency: Normal mode: 2 kHz Pin diameter: 0.
Tally Dascom 2610 Tab Speed Graphic Densities 50 ips Horizontal: 60 / 72 / 80 / 90 / 120 / 180 / 240 / 360 DPI (dot per inch) Vertical: 90 / 180 / 360 DPI Narrow version Print width Wide version 10 CPI: 80 CPL 136 CPL (characters per line) 12 CPI: 96 CPL 163 CPL 15 CPI: 120 CPL 204 CPL 17.
Tally Dascom 2610 Paper Handling Feeding method: Friction (Single) and Tractor (FF-front / FF-rear / FF-pull) Path selection: By selection lever located at the right device side Paper path: Cut sheets: Front in, front or top out Fanfold paper: Front or rear in, top out For details enter the Paper Specifications – 9.
Tally Dascom 2610 Power Supply Unit type: Autosensing wide range power supply Power cord: Detachable Voltage rating: AC 100 to 240V / 47Hz to 63Hz Nominal power: 30W ESD: Comply with IEC801-2; Contact discharge: 4kV Air discharge: 8kV Fuse T6.3AH/250V MTTR < 15 minutes Continuous operation Throughput: 422 p/h in Draft mode according IEC 10561:1999 (ECMA 132) MTBF: 20.
Tally Dascom 2610 X X X X X X X X X X *1 *1 111 Souvenir X X X X X X X X X X X X X X X X X X X X X X X X X X *1 *1 X X X X X X *1 *1 Gothic X X X X X X X X X X X X X X X X X X X X X X X X X X *1 *1 X X X X X X X X X *1 *1 Orator X X X X X X X X X X X X X X X X X X X X X X X X X *1 *1 Script X X X X X X X X X X X X X X X X X X X X X X X X *1 *1 X X X X X X *1 *1 Prestige X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X - OCR-A X X X X X X X X X X X X X X X X X X X X
Souvenir Gothic Orator Script Prestige OCR-A Courier (incl.
Tally Dascom 2610 9.3 Paper Specifications 9.3.
Tally Dascom 2610 9.3.
Tally Dascom 2610 10 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer.
Tally Dascom 2610 10.2 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. 10.2.1 Print Quality Problems and Solutions Problem Printing is too light or too dark. Smears and stains appear on the page.
Tally Dascom 2610 10.2.2 Paper Handling Problems and Solutions Problem Paper cannot be loaded or fed. Paper jams while loading. Paper jams while printing. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Paper width error. 10.2.3 Solution • Make sure that the paper select lever located on the top right of the printer is set correctly. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path.
Tally Dascom 2610 • Make sure that the Online indicator is lit. • If you use the interface cable, make sure it is securely connected to both the printer and the computer. • Make sure paper is loaded. • Run the printer Status Page. If printing executes The printer is on but it will not normally, the problem is caused by: the interface, the print. computer, incorrect printer settings, or incorrect software settings.
Tally Dascom 2610 FCC STATEMENT Changes or modifications not expressly approved by the responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable against harmful interference in a residential installation.
Tally Dascom 2610 DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House,Priestley Road, Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81,WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.
