IR HIGH SPEED DOME CAMERA User’s Manual
CONTENTS Chapter 1 Precautions............................................................... 3 Chapter 2 Structure ................................................................... 5 Chapter 3 Dome Settings .......................................................... 7 Chapter 4 Installation Guide ................................................... 10 Chapter 5 Functions Description ........................................... 13 5．1 Features......................................................
Chapter 1 Precautions ● Please read this manual carefully before installation. ● Handle with care In transportation and storage process, we need to prevent stress, such as severe vibration, and immersion to avoid any damage to the product. This product must be carried disassembled and packaged, either in delivery to users or in return delivery to the factory for repairing. Damage caused by assembled transportation will not be covered by warranty.
● Do not put any object into the product Make sure that there is no metal object or flammable materials inside the product. Such objects or materials may lead to fire, short circuit or damage. If water or liquid flow into the product, turn off the power and disconnect the power cord immediately, and then negotiate with the company. Be careful to protect the camera. Avoid the rain, sea erosion.
● Camera Module Specification Items 15-CD60W-1010 Zoom Camera FCB-EX1010 Image Sensor 1/4” EX-View HAD CCD Picture Elements NTSC:768(H)x494(V)/PAL:752x582(V) Resolution 530TV Line Video Output 1Vp-p Composite Video(75Ω) SYNC System Internal/External (V-Lock) Lens 3.4mm~122.4mm, F1.6~F4.5 Zoom 432X, 36X Optical, 12X Digital S/N Ratio 50dB Mini. Illumination 0.
Chapter 2 Structure Front view Side view
Chapter 3 Dome Settings Protocol Setting This product supports two protocols: PELCO-P、PELCO-D, and two baud rate: 9600BPS, 4800BPS, 2400BPS. Protocol dip switch is bit 1~3 of SW2. Baud Rate Setting Baud rate setting dip switch is bit 4~5 of SW2.
Dome Address Setting 8-bit dip switch （SW1）at dome side is for setting dome address. Dome setting adopts binary system, the 8th bit is the highest, the 1st bit is the lowest. Total 255 dome addresses could be set.
Dome address code table under protocol PELCO-D： *Notice: 1. “1” means “on” status and “0” means “off” status. 2. Dip switch for protocol PELCO-P are the same, while dip switch for PELCO-D is slightly different. PELCO_D protocol supports maximum 254 dome addresses.
Chapter 4 Installation Guide 1、Take out the bracket and unscrew the power box from the bracket. 2、Thread cables across the bracket and connect them to the circuit board in the power box. Install the dome body to the bracket, screw up with 4 ...inner hexagon screws. If necessary, apply water-proof glue to the joint gap. 3、unscrew the cover with the mark “SET”, set communication protocol and addresses. Screw up again with care to avoid water.
4、Attach the drill positioning paste to the wall, and drill according to the paste, and install expansion bolts. 5、Install the dome body together with bracket and power box to the expansion bolts, and tighten with screws.
6、Remove two screws from the power box, and open it. Thread power cable（AC220V）through the water-proof head on the left, and RS485 and video cable through the water-proof head on the right. Connect cables to the circuit board, double check order of connection to avoid damage from wrong connection. After cable connection, tighten the two heads, if necessary, appl water-proof glue to the heads. 7、close power box, tighten the bracket to the power box.
Chapter 5 Functions Description 5．1 Features 1.
3. Built-in High Definition Day/Night Camera ● Auto iris, auto back light compensation ● Auto/manual white balance ● Auto/manual focus ● Auto/manual brightness control ● 530TV line ● Multiple kinds of camera for options 4.
● Timing Running Function Users can set speed dome operation task at different time during one week. ● Direction Indication Function Users can set North by themselves, and also can set indication area. When speed dome turns to the area, the tilt will be displayed in screen. ● Motion Detection Function For some special cameras, the dome can auto track the moving things. ● 3D Location Function In dome effective zoom scope, can zoom in and out any area on screen, also can move any point to center.
● Auto Cruising Users can program some preset positions into auto cruising sequence, then the speed dome can track as it. Each cruising tracks has 32 preset positions. ● Pattern Tour Speed Dome can memory 180s running path or 500 orders. When start pattern tour, speed dome can track as recording path. It supports 4 groups pattern tour. ● Guard Location The dome will rotate back to preset position after a period of vacant time.
objects ● Target is behind the glass with droplets and dust. ● Target moves too fast ● Large area targets, such as walls; ● Target are too dark or inherently ambiguous; 3) Auto Iris Control Auto sense ambient light, and make quick adjustments. 4) Auto Back Compensation In the bright background, auto compensate light for the target, and adjust the back light. 5) Auto/Manual White Balance Auto/Manual adjust depending on the environment light changes.
Chapter 6 Operation instruction The user can call upon preset position 95 to enter the setting interface of the OSD menu.
Language It supports two language option Chinese and English. Call upon preset position 95 to enter the setting interface of the OSD menu and move to “language setting”, push “ Iris on” to enter setting and move the joystick to switch Chinese/English.
joystick, select “display” enter submenu of “display”. A：DOME Press “Iris on” to set DOME SETTING and with “ON/OFF” option. B：PRESET Press “Iris on” to set PRESET SETTING and with ON/OFF/2SEC/5SEC/10SEC option. C：AUTO Press “Iris on” to set AUTO SETTING and with ON/OFF/2SEC/5SEC/10SEC option. D：ZONES Press “Iris on” to set ZONES SETTING and with ON/OFF/2SEC/5SEC/10SEC option. E：DATE/TIME Press “Iris on” to set DATE/TIME SETTING and move joystick to select ON/OFF/2SEC/5SEC/10SEC option.
B：DOME Press “Iris on” to set DOME SETTING and move joystick to adjust DOME until get best position. Press “Iris on” to confirm. C：ZONES Press “Iris on” to set ZONES SETTING and move joystick to adjust ZONES until get best position. Press “Iris on” to confirm. D：AUTO Press “Iris on” to set AUTO SETTING and move joystick to adjust AUTO until get best position. Press “Iris on” to confirm. E：PAN/TILT Press “Iris on” to set PAN/TILT SETTING and move joystick to adjust PAN/TILT until get best position.
Move the cursor to “IR LED”, and press iris open to submenu. A1：Open Control Type Move the cursor to “Open Control Type”, and press iris open to select IR light control type; move the joystick to set IR light control type as “External synchronization Auto/ Internal Synchronization Auto /Time Schedule/Open/Close”. Instruction of five control types： 1：External synchronization Auto：Open or close of IR LED will depend on light sensor completely, and dome will control the day/night switch.
B1：Environment Threshold Value User can adjust the environment light threshold value as to different application locations. In External synchronization Auto type, default value is 1~2lux（there may be slight difference because of the direction of IR LED. IR LED is on in light condition. Threshold value can be set from 1 to 10. 1 means that the light is weak and 10 means that the light is strong.
illumination value. I1：Illumination of light group 3 Light group 3 is inside lane short distance IR LED, press “Iris on” to set illumination value. When close zoom match, user should adjust irradiation distance by himself. Note: When open zoom match, it can’t adjust illumination of Light group 1, Light group 2 and Light group 3 manually. B：STANDBY SETTINGS Move cursor to STANDBY SETTINGS and press “Iris on” to submenu of STANDBY SETTINGS.
A1. PRIVACY MASK Move cursor to PRIVACY MASK and press “Iris on” to setup. Move joystick to select privacy mask and it supports 8 masks in total. B1.ENABLE Move cursor to ENABLE and press “Iris on” to setup switch of privacy mask. Move joystick to select the state: on and off. C1.SETUP Move cursor to SETUP and press “Iris on” to setup the position of privacy mask, press “Iris on” to confirm. Move cursor to the privacy mask, press “Iris on” to enter the privacy size setting and move joystick to adjust size.
Move cursor to DATE SETTING and press “Iris on” to setup date. Right/left shift joystick to setup position and Upper and down shift joystick to setup increase and decrease of date. Press “Iris on” to confirm. B1：TIME SETTING Move cursor to TIME SETTING and others same with DATE SETTING. Move cursor to SAVE SETTING and press “Iris on” to confirm. If cancel current setting, move cursor to BACK, press “Iris on” back to the last submenu and cancel setting. E：MANUAL CONTROL A1.
B1.Password protection Move the cursor to “password protection”, and press iris open button to password switch setup; move the joystick upward and downward to open or shut password protection. When password protection is open, input password before opening the menu.
Input method instruction： 1． Move the cursor to “input information”, and press iris open to information edit mode. Move the joystick left and rightward to move the cursor “←”, and press iris on to delete the character by the cursor and press iris off to exit edit mode. 2． Move the cursor to input method option which is one line below “Input Information”, and press iris on to input method setup mode.
downward to chose the input methods, which contain “English Capital/English lower case /Chinese/Number/Special character/”. 3． Move the cursor to one line below input method option, and press iris on to character input mode. Now selected character twinkles, and move the joystick to select characters; press iris on to input the twinkling character to the position of “←”in the “Input information” block. H：Other Options Move the cursor to “other options”, and press iris on to its submenu.
code and after that, dome will pause automatically, and 5、15、30、60 seconds option. E1.Menu shut time With menu on, menu will automatically shut after a period of vacant time. Move the cursor to “menu shut time”, and press iris on to setup mode; move the joystick upward or downward to set time as“1 min/2 mins/5 mins/10 mins” F1.Directi Zero Position Move the cursor to “Direction Zero Setup”,and press iris on to direction zero position setup mode. It shows “press iris on to confirm...
Move the joystick upward and downward to open or shut this function E. Vertical Mirror Image Move the cursor to “Vertical mirror image”,and press iris on to enter vertical image switch setup. Move joystick upward and downward to select on/off. F. Zoom Speed Move the cursor to “Zoom Speed”,and press iris on to zoom speed setup mode. Move joystick to select camera zoom speed, which can be set as“Low speed”、“moderate speed”、“high speed”. G：Advanced option A1.
D1.Illumination Move the cursor to “illumination”, and press iris on to enter setup mode. Move the joystick upward or downward to set illumination value. E1.Exposure mode Move the cursor to“exposure mode”,and press iris on to setup mode. Move the joystick upward and downward to select parameters, which can be set as“Auot/Manual/Sutter priority/iris priority/Illumination priority”. Note：For different cameras, the mode options might be different. F1.
A: Preset A1. Preset Position Number Move joystick to“preset position number”, and press iris on to setup mode. Move joystick upward and downward to set number. This dome supports 220 preset positions,1-64,100-255. B1. Title Setup Move cursor to“title setup”, and press iris on to setup submenu to make preset position title setup. C1.Call Move cursor to“call”, and press iris on to call related preset position. D1.Setup Press iris on to preset position setup mode, and it shows ”Press iris on to confirm…”.
A1.Scan Number Move the cursor to“scan number”,and press iris on to setup mode. Move joystick upward and downward to set scan number. This dome supports 8 auto scans. B1. Title Setup Move cursor to “Title Setup”,and press iris on to enter scan title setup submenu to set the title. C1.Start Scan Move cursor to“start scan”,and press iris on to start related scan. D1.Left Boundary Setup Move cursor to “Set left boundary”,and press iris on to setup mode, it shows ”press iris on to confirm…”.
the edition mode of sequence No., move the joystick upward and downward to select number. Then press IRIS ON to confirm. B1. TITLE Move the cursor to TITLE and press IRIS ON to enter the edition mode of sequence title. C1.START MOVE the cursor to START and press IRIS ON to start the current sequence. D1. Press IRIS ON to enter into the sequence setting SEQUENCE ―――――――――――――― SEQ NO. : 1 TITLE : SEQ 1 START DELETE BACK EXIT SEQUENCE ―――――――――――――― NO.
E1. Delete Move cursor to“delete”，press Iris On to delete related sequence. D. PATTERN MOTION ―――――――――――――― BACK EXIT PATTERN ―――――――――――――― PATTERN NO. : 1 TITLE : PATTERN 1 START DELETE BACK EXIT A1. PATTERN NO. Move the cursor to PATT and press the key IRIS ON(key on control keyboard) to enter the edition mode of sequence No., move the joystick upward and downward to select number. Then press IRIS ON to confirm.
MOTION ―――――――――――――― BACK EXIT ZONES ―――――――――――――― － ZONE IS NOT SET － ZONE NO. : 1 TITLE NO. : ZONE 1 DELETE A1 B1 C1 D1 E1 F1 BACK EXIT A1.ZONE INFORMATION B1.ZONE NO. Move the cursor to ZONE NO. and press the key IRIS ON(key on control keyboard) to enter the edition mode of zone No., move the joystick upward and downward to select number. Then press IRIS ON to confirm. C1.
A1 B1 MOTION ―――――――――――――― TIMING ACTION ―――――――――――――― C1 NO. START STOP MOTION 0 0 : 0 0 0 0 : 0 0 NONE 1 2 0 0 : 0 0 0 0 : 0 0 NONE 0 0 : 0 0 0 0 : 0 0 NONE 3 0 0 : 0 0 0 0 : 0 0 NONE 4 0 0 : 0 0 0 0 : 0 0 NONE 5 0 0 : 0 0 0 0 : 0 0 NONE 6 0 0 : 0 0 0 0 : 0 0 NONE 7 0 0 : 0 0 0 0 : 0 0 NONE 8 D1 MON COPY BACK G1 OFF F1 E1 TIMING ACTION：The user could set up the required functions during the designated time periods.
G1. BACK Go back to upper menu Note： The settings of each time periods can not overlaid, and the time period can not be allowed to exceed 00:00 If the use tries to control the dome during the TIMING ACTION, then the operation will be stopped and if there is no operation after 25 seconds, then the dome will resume the timing action.
*Notice: The auto tracking function is only for the speed dome with the camera module which supports auto tracking. RESTART Press “Iris Open” to restart the dome.
HELP Press “Iris Open” to check all the HELP information about the menu settings.
