5-inch High-definition Network Speed Dome User Manual V4.0.2 Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.
User Manual of Network Speed Dome 1 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to Network Speed Dome. This manual may contain several technical or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
User Manual of Network Speed Dome 2 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
User Manual of Network Speed Dome 3 Safety Warnings and Cautions Please pay attention to the following warnings and cautions: Hazardous Voltage may be present: Special measures and precautions must be taken when using this device. Some potentials (voltages) on the device may present a hazard to the user. This device should only be used by employees from our company with knowledge and training in working with these types of devices that contain live circuits.
User Manual of Network Speed Dome 4 Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency in your region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, female connector. See the following website for more information http://kropla.com/electric2.htm.
User Manual of Network Speed Dome 5 determined by turning the equipment on and off, the user is required to take measures to eliminate the interference or discontinue the use of this equipment. Lead Content: Please recycle this device in a responsible manner. Refer to local environmental regulations for proper recycling; do not dispose of device in unsorted municipal waste. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 6 Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
User Manual of Network Speed Dome 7 Cautions: Make sure the power supply voltage is correct before using the product. Do not drop the product or subject it to physical shock. Do not install the product on vibratory surface or places. Do not expose it to high electromagnetic radiating environment. Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the product.
User Manual of Network Speed Dome 8 Table of Contents Chapter 1 Overview........................................................................................................... 10 1.1 System Requirement.................................................................................................................... 10 1.2 Appearance ..................................................................................................................................10 1.3 Features .................
User Manual of Network Speed Dome 6.3 9 Configuring Network Settings .....................................................................................................47 6.3.1 Configuring TCP/IP Settings.....................................................................................................47 6.3.2 Configuring Port Settings ........................................................................................................48 6.3.3 Configuring PPPoE Settings .....................
10 User Manual of Network Speed Dome Chapter 1 Overview 1.1 System Requirement System requirement of web browser accessing is as follows: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.
User Manual of Network Speed Dome 11 Scheduled PTZ movement Camera features: Auto iris, auto focus, auto white balance, backlight compensation and auto day & night switch Privacy Masks programmable PTZ features: 360° endless pan range and -5°-90° tilt range 256 presets programmable, preset image freezing capability 8 patrols, up to 32 presets per patrol 4 patterns, with the recording time not less than 10 minutes per pattern Proportional pan/tilt function Park action: auto callup of PTZ
User Manual of Network Speed Dome 12 depending on different camera models. Privacy Mask This function allows you to block or mask certain area of a scene, for preventing the personal privacy from recording or live viewing. A masked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.
User Manual of Network Speed Dome 13 A patrol is a memorized series of pre-defined preset function. The scanning speed between two presets and the dwell time at the preset are programmable. Pattern A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default the focus and iris are in auto status during the pattern is being memorized. Power Off Memory The dome supports the power off memory capability with the predefined resume time.
User Manual of Network Speed Dome 14 Chapter 2 Network Connection Before you start: If you want to set the network speed dome via a LAN (Local Area Network), please refer to Section 2.1 Setting the Network Speed Dome over the LAN. If you want to set the network speed dome via a WAN (Wide Area Network), please refer to Section 2.2 Setting the Network Speed Dome over the WAN. 2.
User Manual of Network Speed Dome 15 Figure 2-2 Connecting via a Switch or a Router 2.1.2 Detecting and Changing the IP Address You need the IP address to visit the network speed dome. Steps: 1. To get the IP address, you can choose either of the following methods: Use SADP, a software tool which can automatically detect the online network speed domes in the LAN and list the device information including IP address, subnet mask, port number, device serial number, device version, etc.
16 User Manual of Network Speed Dome Figure 2-3 SADP Interface 2.2 Setting the Network Speed Dome over the WAN Purpose: This section explains how to connect the network speed dome to the WAN with a static IP or a dynamic IP. 2.2.1 Static IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can connect the network speed dome via a router or connect it to the WAN directly.
User Manual of Network Speed Dome 17 Figure 2-4 Accessing the Speed Dome through Router with Static IP Connecting the network speed dome with static IP directly You can also save the static IP in the speed dome and directly connect it to the internet without using a router. Refer to Section 2.1.2 Detecting and Changing the IP Address for detailed IP address configuration of the speed dome. Figure 2-5 Accessing the Speed Dome with Static IP Directly 2.2.
User Manual of Network Speed Dome 18 This speed dome supports the PPPoE auto dial-up function. The speed dome gets a public IP address by ADSL dial-up after the speed dome is connected to a modem. You need to configure the PPPoE parameters of the network speed dome. Refer to Section 6.3.3 Configuring PPPoE Settings for detailed configuration.
User Manual of Network Speed Dome 19 Figure 2-8 Private Domain Name Resolution Steps: 1. Install and run the IP Server software in a computer with a static IP. 2. Access the network speed dome through the LAN with a web browser or the client software. 3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
20 User Manual of Network Speed Dome Chapter 3 Access to the Network Speed Dome 3.1 Accessing by Web Browsers Steps: 1. Open the web browser. 2. In the address field, input the IP address of the network speed dome, e.g., 192.0.0.64 and press the Enter key to enter the login interface. 3. Input the user name and password and click . Note: The default user name is admin, password is 12345. Figure 3-1 Login Interface 4. Install the plug-in before viewing the live video and operating the speed dome.
User Manual of Network Speed Dome Figure 3-2 Download and Install Plug-in Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 22 Figure 3-5 Install Plug-in (3) Note: You may have to close the web browser to install the plug-in. Please reopen the web browser and log in again after installing the plug-in. 3.2 Accessing by Client Software 3.2.1 Installing iVMS-4200 Software The product CD contains the iVMS-4200 client software. You can view the live video and manage the speed dome with the client software. Follow the installation prompts to install the client software and WinPcap.
User Manual of Network Speed Dome 23 Figure 3-6 iVMS-4200 Control Panel Figure 3-7 iVMS-4200 Live View Interface 3D Positioning: Steps: 1. Click on the PTZ control panel of live view interface. 2. Operate the 3D positioning function: Left click a position of the live video. The corresponding position will be © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 24 moved to the center of the live video. Hold down the left mouse button and drag the mouse to the lower right on the live video. The corresponding position will be moved to the center of the live video and zoomed in. Hold down the left mouse button and drag the mouse to the upper left on the live video. The corresponding position will be moved to the center of the live video and zoomed out.
25 User Manual of Network Speed Dome Chapter 4 Live View 4.1 Power-up Action After the power is applied, the speed dome will perform self-test actions. It begins with lens actions and then pan and tilt movement. After the power-up self-test actions, the information as shown in Figure 4-1 will be displayed on screen for 40 seconds. The System Information displayed on the screen includes the dome address, protocol, version and other information.
26 User Manual of Network Speed Dome Descriptions of the live view page: Click to show or hide Menu Bar PTZ control panel Live View Parameters PTZ control Live view window Preset/patrol/pattern Toolbar Figure 4-2 Live View Page Menu Bar: Click each tab to enter Live View, Playback, Log and Configuration page respectively. Live View Window: Display the live video. Toolbar: Operations on the live view page, e.g., live view, capture, record, audio on/off, two-way audio, etc.
27 User Manual of Network Speed Dome Figure 4-3 Start Live View Table 4-1 Descriptions of the Toolbar Icon Description Icon Live view on Description Live view off Manually capture the pictures Manual recording off Manual recording on Audio on and adjust volume Mute Two-way audio off Two-way audio on Note: Before using the two-way audio or recording with audio functions, please set the Stream Type to Video & Audio referring to Section 6.4.1 Configuring Video Settings.
28 User Manual of Network Speed Dome 4.4 Recording and Capturing Pictures Manually In the live view interface, click click on the toolbar to capture the live pictures or to record the live video. The local saving paths of the captured pictures and clips can be set in the Configuration > Local Configuration interface. To configure remote automatic recording, please refer to Section 7.2 Configuring Recording Schedule. Note: The captured image will be saved as a JPEG file in your computer. 4.
User Manual of Network Speed Dome 29 4.5.2 Setting / Calling a Preset Purpose: A preset is a predefined image position. For the defined preset, you can click the calling button to quickly view the desired image position. Setting a Preset: Steps: 1. In the PTZ control panel, select a preset number from the preset list. Figure 4-5 Setting a Preset 2. Use the PTZ control buttons to move the lens to the desired position. • Pan the speed dome to the right or left. • Tilt the speed dome up or down.
30 User Manual of Network Speed Dome Figure 4-6 Calling a Preset Note: The following presets are predefined with special commands. You can only call them but not configure them. For instance, preset 99 is the “Start auto scan”. If you call the preset 99, the speed dome starts auto scan function.
31 User Manual of Network Speed Dome Please make sure that the presets you want to add into a patrol have been defined. Setting a Patrol: Steps: 1. In the PTZ control panel, click 2. Select a patrol number from 3. Click to enter the patrol settings interface. . to enter the adding interface of preset as shown in Figure 4-7. Figure 4-7 Adding Presets 4. Configure the preset number, patrol time and patrol speed. Name Description Patrol Time It is the duration staying on one patrol point.
32 User Manual of Network Speed Dome Figure 4-8 Calling a Preset Buttons on the Patrols interface: Buttons Description Save a patrol Call a patrol Stop a patrol Enter the adding interface of preset Modify a preset Delete a preset Delete all the presets in one patrol 4.5.4 Setting / Calling a Pattern Purpose: A pattern is a memorized series of pan, tilt, zoom, and preset functions. It can be called on the pattern settings interface. There are up to 4 patterns for customizing.
33 User Manual of Network Speed Dome 3. Click to enable recording the panning, tilting and zooming actions. 4. Use the PTZ control buttons to move the lens to the desired position after the information of PROGRAM PATTERN REMAINNING MENORY(%) shown in Figure 4-10 is displayed on the screen. • Pan the speed dome to the right or left. • Tilt the speed dome up or down. • Zoom in or out. • Refocus the lens. Figure 4-10 Remaining Memory 5. Click to save all the pattern settings.
User Manual of Network Speed Dome stream type is 34 . Note: Please refer to Section 6.4.1 Configuring Video Settings for more detailed parameter settings of the main stream and sub-stream respectively. Image Size: You can scale up/down the live view image by clicking image size can be 4:3, 16:9, original or auto. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. .
User Manual of Network Speed Dome 35 Chapter 5 PTZ Configuration 5.1 Configuring Initial Position Purpose: The initial position is the origin of PTZ coordinates. It can be the factory default initial position. You can also customize the initial position according to your own demand. Customize an Initial Position: Steps: 1. Enter the Initial Position Configuration interface: Configuration > Advanced Configuration > PTZ > Initial Position Figure 5-1 PTZ Configuration 2.
User Manual of Network Speed Dome 36 5.2 Configuring Basic PTZ Parameters Purpose: You can configure the basic PTZ parameters, including proportional pan, preset freezing, preset speed, etc. 1. Enter the Basic PTZ Parameter Configuration interface: Configuration > Advanced Configuration > PTZ > Basic Figure 5-2 Basic PTZ Configuration Interface 2.
User Manual of Network Speed Dome 37 Zoom Status: Set the OSD duration of zooming status as 2 seconds, 5 seconds, 10 seconds, Always Close or Always Open. PT Status: Set the azimuth angle display duration while panning and tilting as 2 seconds, 5 seconds, 10 seconds, Always Close or Always Open. Preset Status: Set the preset name display duration while calling the preset as 2 seconds, 5 seconds, 10 seconds, Always Close or Always Open.
User Manual of Network Speed Dome 38 2. Click the checkbox of Enable Limit and choose the limit type as manual stops or scan stops. Manual Stops: When manual limit stops are set, you can operate the PTZ control panel manually only in the limited surveillance area. Scan Stops: When scan limit stops are set, the random scan, frame scan, auto scan, tilt scan, panorama scan is performed only in the limited surveillance area. Note: Manual Stops of Limit Type is prior to Scan Stops.
User Manual of Network Speed Dome 4. 39 Set the schedule and task details. Steps: (1) Click to edit the task schedule. Figure 5-5 Edit the Schedule and Task Type (2) Choose the day you want to set the task schedule. (3) Click All Day to set the schedule as all day; or click Customize and input the Start Time and End Time for each task, and click Enter on your keyboard to enter the time. (4) Choose the task type from the drop-down list. You can choose scan, preset, pattern and etc.
40 User Manual of Network Speed Dome Figure 5-6 Task Types (5) After you set the scheduled task, you can copy the task to other days (Optional). (6) Click to save the settings. Note: The time of each task can’t be overlapped. Up to 10 tasks can be configured for each day. 5. Click to save the settings. 5.5 Configuring Park Actions Purpose: This feature allows the dome to start a predefined park action (scan, preset, pattern and etc.) automatically after a period of inactivity (park time).
41 User Manual of Network Speed Dome Figure 5-8 Action Types 5. Click to save the settings. 5.6 Configuring Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video to prevent certain spots in the surveillance area from being live viewed and recorded. Steps: 1. Enter the Privacy Mask Settings interface: Configuration > Advanced Configuration> PTZ > Privacy Mask Figure 5-9 Draw the Privacy Mask 2.
42 User Manual of Network Speed Dome 5. Click to save the privacy mask, and it will be listed in the Privacy Mask List area; you can select a mask and click to delete it from the list; you can also define the color of the masks. Figure 5-10 Privacy Mask List Figure 5-11 Define Mask Color 6. Check the checkbox of Enable Privacy Mask to enable this function. Note: You are allowed to draw up to 24 areas on the same image. 5.
User Manual of Network Speed Dome 43 Chapter 6 Speed Dome Configuration 6.1 Configuring Local Parameters Note: The local configuration refers to the parameters of the live view and other operations using the web browser. Steps: 1. Enter the Local Configuration interface: Configuration > Local Configuration Figure 6-1 Local Configuration Interface 2. Configure the following settings: Live View Parameters: Set the protocol type, stream type, image size and live view performance.
44 User Manual of Network Speed Dome refer to Section 6.3.1 Configuring TCP/IP Settings. Stream Type: Set the stream type to main stream or sub-stream for live view by web browser. Please refer to Section 6.4.1 Configuring Video Settings for the parameter settings of the main stream and sub-stream respectively. Image Size: Set the image size to original, 4:3 or 16:9. Live View Performance: Set the live view performance to Least Delay, Balanced or Best Fluency.
45 User Manual of Network Speed Dome Figure 6-2 Time Settings Configuring Time Synchronization by NTP Server (1) Check the checkbox to enable the NTP function. (2) Configure the following settings: Server Address: IP address of NTP server. NTP Port: Port of NTP server. Interval: The time interval between the two synchronizing actions by NTP server. It can be set from 1 to 10080 minutes.
46 User Manual of Network Speed Dome network, NTP software can be used to establish a NTP server for time synchronization. Configuring Time Synchronization Manually (1) Check the Manual Time Sync checkbox. (2) Click to set the system time from the pop-up calendar. (3) Click to save the settings. Note: You can also check the Sync with local time checkbox to synchronize the time of the speed dome with the time of your computer.
47 User Manual of Network Speed Dome (2) Set the date of the DST period. (3) Click to save the settings. Figure 6-6 DST Settings 6.3 Configuring Network Settings 6.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the speed dome over network. Steps: 1. Enter TCP/IP Settings interface: Configuration > Basic Configuration > Network > TCP/IP Or Configuration > Advanced Configuration > Network > TCP/IP © Hikvision Digital Technology Co., Ltd.
48 User Manual of Network Speed Dome Figure 6-7 TCP/IP Settings 2. Configure the NIC settings, including the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway. 3. Click to save the above settings. Notes: If the DHCP server is available, you can check to automatically obtain an IP address and other network settings from that server. The valid value range of Maximum Transmission Unit(MTU) is 500 ~ 9676. The default value is 1500.
User Manual of Network Speed Dome 2. Set the HTTP port, RTSP port and port of the speed dome. HTTP Port: The default port number is 80. RTSP Port: The default port number is 554. 3. Click 49 to save the settings. 6.3.3 Configuring PPPoE Settings Purpose: If you have no router but only a modem, you can use Point-to-Point Protocol over Ethernet (PPPoE) function. Steps: 1. Enter the PPPoE Settings interface: Configuration >Advanced Configuration > Network > PPPoE Figure 6-10 PPPoE Settings 2.
User Manual of Network Speed Dome 50 Figure 6-11 DDNS Settings 2. Check the Enable DDNS checkbox to enable this feature. 3. Select DDNS Type. Two DDNS types are selectable: IPServer and DynDNS. DynDNS: Steps: (1) Enter Server Address of DynDNS (e.g. members.dyndns.org). (2) In the Domain text field, enter the domain name obtained from the DynDNS website. (3) Enter the Port of DynDNS server. (4) Enter the User Name and Password registered on the DynDNS website. (5) Click to save the settings.
User Manual of Network Speed Dome 51 computer that runs the IP Server software. For the IP Server, you have to apply a static IP, subnet mask, gateway and preferred DNS from the ISP. Figure 6-13 IPServer Settings 6.3.5 Configuring SNMP Settings Purpose: You can use SNMP to get speed dome status and parameters related information. Before you start: Before setting the SNMP, please use the SNMP software and manage to receive the speed dome information via SNMP port.
52 User Manual of Network Speed Dome Figure 6-14 SNMP Settings 2. Check the corresponding version checkbox ( , , ) to enable the feature. 3. Configure the SNMP settings. Note: The configuration of the SNMP software should be the same as the settings you configure here. 4. Click to save and finish the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
53 User Manual of Network Speed Dome 6.3.6 Configuring FTP Settings Purpose: You can set a FTP server and configure the following parameters for uploading captured pictures. Steps: 1. Enter the FTP Settings interface: Configuration >Advanced Configuration > Network > FTP Figure 6-15 FTP Settings 2. Configure the FTP settings, including server address, port, user name, password, directory and upload type.
User Manual of Network Speed Dome 54 Figure 6-17 Child Directory 3. Upload type: To enable uploading the captured picture to the FTP server. Click to save the settings. Note: If you want to upload the captured pictures to FTP server, you also have to enable the continuous snapshot or event-triggered snapshot in Snapshot interface. For detailed information, please refer to the Section 6.6.8 Configuring Snapshot Settings. 6.4 Configuring Video and Audio Settings 6.4.
User Manual of Network Speed Dome 55 Refer to the Section 6.1 Configuring Local Parameters for switching the main stream and sub-stream for live viewing. 3. You can customize the following parameters for the selected main stream or sub-stream: Video Type: Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. Resolution: Select the resolution of the video output.
User Manual of Network Speed Dome 56 Audio Encoding: G.711ulaw. 3. Click to save the settings. 6.5 Configuring Image Settings 6.5.1 Configuring Display Settings Purpose: You can set the image quality of the speed dome, including brightness, contrast, saturation, sharpness, etc. Note: The parameters in Display Settings interface vary depending on the models of speed dome. Steps: 1.
57 User Manual of Network Speed Dome Brightness This feature is used to adjust brightness of the image. The value ranges from 0 to 100. Contrast This feature enhances the difference in color and light between parts of an image. The value ranges from 0 to 100. Saturation This feature is used to adjust color saturation of the image. The value ranges from 0 to 100. Sharpness Sharpness function enhances the detail of the image by sharpening the edges in the image. The value ranges from 0 to 100.
58 User Manual of Network Speed Dome brightness of the environment. Iris Priority: The value of iris needs to be adjusted manually. The shutter and gain values will be adjusted automatically according to the brightness of the environment. Figure 6-21 Manual Iris Shutter Priority: The value of shutter needs to be adjusted manually. The iris and gain values will be adjusted automatically according to the brightness of the environment.
59 User Manual of Network Speed Dome Mirror If you turn the MIRROR function on, the image will be flipped. It is like the image in the mirror. The flip direction can be set to OFF, LEFT/RIGHT, UP/DOWN or CENTER. Note: This function varies depending on the models of speed dome. Slow Shutter This function can be used in underexposure condition. It lengthens the shutter time to ensure full exposure. The slow shutter value can be set to Low, Normal and High.
User Manual of Network Speed Dome 60 according to the color temperature of the scene illumination. Onepush: Selecting Onepush mode, the viewed image retains color balance automatically according to the current color temperature. Note: This function varies depending on the models of speed dome. Zoom Limit You can set Zoom Limit value to limit the maximum value of zooming. The value can be set to 18, 36, 72, 144 and 216. Note: This function varies depending on the models of speed dome. 6.5.
61 User Manual of Network Speed Dome Figure 6-27 OSD Settings 2. Check the corresponding checkbox to select the display of speed dome name, date or week if required. 3. Edit the speed dome name in the text field of Camera Name. 4. Select from the drop-down list to set the time format, date format and display mode. 5. You can use the mouse to click and drag the text frame in the live view window to adjust the OSD position. Figure 6-28 Adjust OSD Location 6. Click to activate above settings. 6.5.
User Manual of Network Speed Dome 62 Note: There are up to 4 text overlays configurable. Figure 6-29 Text Overlay Settings 6.6 Configuring and Handling Alarms Purpose: This section explains how to configure the network speed dome to respond to alarm events, including motion detection, external alarm input, video loss, tamper-proof and exception. These events can trigger the alarm actions, such as Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
63 User Manual of Network Speed Dome Figure 6-30 Enable Motion Detection (3) Click . Click and drag the mouse on the live video image to draw a motion detection area. Note: You can draw up to 8 motion detection areas on the same image. (4) Click Note: You can click 2. to finish drawing. to clear all of the areas. (5) Move the slider detection. Set the Arming Schedule for Motion Detection.
User Manual of Network Speed Dome 64 Figure 6-31 Arming Schedule (2) Choose the day you want to set the arming schedule as shown in Figure 6-32. (3) Click to set the time period for the arming schedule. (4) After you set the arming schedule, you can click to copy the schedule to other days (Optional). (5) Click to save the settings. Note: The time of each period can’t be overlapped. Up to 4 periods can be configured for each day. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 65 Figure 6-32 Arming Time Schedule 3. Set the Alarm Actions for Motion Detection. Purpose: You can specify the linkage method when an event occurs. The following contents are about how to configure the different types of linkage method. Figure 6-33 Linkage Method Check the checkbox to select the linkage method. Notify surveillance center, send email, upload to FTP, trigger channel and trigger alarm output are selectable.
User Manual of Network Speed Dome 66 6.6.7 Configuring Email Settings to set the Email parameters. Upload to FTP Capture the image when an alarm is triggered and upload the picture to a FTP server. Note: You need a FTP server and set FTP parameters first. Refer to Section 6.3.6 Configuring FTP Settings for setting FTP parameters. Trigger Channel Record a video when an event occurs. Note: You have to set the recording schedule to realize this function. Please refer to Section 7.
User Manual of Network Speed Dome 67 Figure 6-34 Tamper-proof Alarm 2. Check Enable Tamper-proof checkbox to enable the tamper-proof detection. 3. Set the tamper-proof area. Refer to Step 1 Set the Motion Detection Area in Section 6.6.1 Configuring Motion Detection. 4. Click to edit the arming schedule for tamper-proof. The arming schedule configuration is the same as the setting of the arming schedule for motion detection. Refer to Step 2 Set the Arming Schedule for Motion Detection in Section 6.6.
User Manual of Network Speed Dome 68 2. Configuration > Advanced Configuration> Events > Alarm Input: Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). 3. Edit the name in to set a name for the alarm input (optional). Figure 6-35 Alarm Input Settings 4. 5. 6. 7. Click to set the arming schedule for the alarm input. Refer to Step 2 Set the Arming Schedule for Motion Detection in Section 6.6.1 Configuring Motion Detection.
User Manual of Network Speed Dome 8. Click 69 to save the settings. Figure 6-36 Linkage Method 6.6.4 Configuring Alarm Output Steps: 1. Enter the Alarm Output Settings interface: Configuration>Advanced Configuration> Events > Alarm Output 2. Select one alarm output channel in the Alarm Output drop-down list. 3. 4. Set a name in for the alarm output (optional). The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual.
User Manual of Network Speed Dome 70 Figure 6-37 Alarm Output Settings 6.6.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the speed domes. Steps: 1. Enter the Exception Settings interface: Configuration > Advanced Configuration> Events > Exception 2. Check the checkbox to set the actions taken for the Exception alarm. Refer to © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 71 Step 3 Set the Alarm Actions Taken for Motion Detection in Section 6.6.1 Configuring Motion Detection. Figure 6-38 Exception Settings 3. Click to save the settings. 6.6.6 Configuring Email Settings Purpose: The system can be configured to send an Email notification to all designated receivers if an alarm event is detected, e.g., motion detection event, video loss, tamper-proof, etc.
User Manual of Network Speed Dome 72 Figure 6-39 Email Settings 2. Configure the following settings: Sender: The name of the email sender. Sender’s Address: The email address of the sender. SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25. Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP server.
73 User Manual of Network Speed Dome 6.6.7 Configuring Snapshot Settings Purpose: You can configure the scheduled snapshot and event-triggered snapshot. You can upload the captured pictures to a FTP server. Basic Settings Steps: 1. Enter the Snapshot Settings interface: Configuration > Advanced Configuration > Events > Snapshot 2. Check the Enable Timing Snapshot checkbox to enable continuous snapshot. Check the Enable Event-triggered Snapshot checkbox to check event-triggered snapshot. 3.
User Manual of Network Speed Dome Figure 6-40 Snapshot Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 75 Chapter 7 Record Settings Before you start: To configure record settings, please make sure that you have the network storage device within the network or the SD card inserted in your speed dome. 7.1 Configuring NAS Settings Before you start: The network disk should be available within the network and properly configured to store the recorded files, log files, etc. Steps: 1.
76 User Manual of Network Speed Dome Figure 7-2 Initialize Disk Figure 7-3 Initializing When the initialization completed, the status of disk will become Normal as shown in Figure 7-4. Figure 7-4 View Disk Status Notes: Up to 1 NAS disks can be connected to the speed dome. To initialize and use the SD card after insert it to the speed dome, please refer to the steps of NAS disk initialization. 7.
User Manual of Network Speed Dome 77 Figure 7-5 Recording Schedule Interface 2. Check the checkbox of Enable Record Schedule to enable scheduled recording. 3. Set the record parameters of the speed dome. Figure 7-6 Record Parameters Pre-record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the speed dome starts to record at 9:59:55.
User Manual of Network Speed Dome 78 the event. For example, if an alarm triggered recording ends at 11:00, and the post-record time is set as 5 seconds, the speed dome records until 11:00:05. The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min or 10 min. Note: The Pre-record and Post-record parameters vary depending on the speed dome model. 4. Click to edit the record schedule. Figure 7-7 Record Schedule 5. Choose the day to set the record schedule.
User Manual of Network Speed Dome 79 motion is detected. Besides configuring the recording schedule, you have to set the motion detection area and check the checkbox of Trigger Channel in the Linkage Method of Motion Detection Settings interface. For detailed information, please refer to the Step 1 Set the Motion Detection Area in the Section 6.6.1 Configuring Motion Detection.
80 User Manual of Network Speed Dome (3) Check the checkbox and click to copy settings of this day to the whole week. You can also check any of the checkboxes before the date and click (4) Click . to save the settings and exit the Edit Record Schedule interface. 6. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
81 User Manual of Network Speed Dome Chapter 8 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Task 1: To play back the video files Steps: 1. Click on the menu bar to enter playback interface. Figure 8-1 Playback Interface 2. Select the date and click . Figure 8-2 Search Video © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
82 User Manual of Network Speed Dome 3. Click to play the video files found on this date. The toolbar on the bottom of Playback interface can be used to control playing process.
83 User Manual of Network Speed Dome types as shown in Figure 8-6. Figure 8-6 Video Types Task 2: To download the video files Steps: 1. Click on the playback interface. The pop-up menu is shown in Figure 8-7. All the video files are listed. Figure 8-7 Video Downloading interface 2. Check the checkbox 3. Click in front of the video files that you need to download. to download the video files.
84 User Manual of Network Speed Dome to turn pages. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
85 User Manual of Network Speed Dome Chapter 9 Log Searching Purpose: The operation, alarm, exception and information of the speed dome can be stored in log files. You can also export the log files on your demand. Before you start: Please configure network storage for the speed dome or insert a SD card in the speed dome. Steps: 1. Click on the menu bar to enter log searching interface. Figure 9-1 Log Searching Interface 2.
86 User Manual of Network Speed Dome 4. To export the log files, click to save the log files in your computer. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 87 Chapter 10 Others 10.1 Managing User Accounts Enter the User Management interface: Configuration >Basic Configuration> Security > User Or Configuration > Advanced Configuration> Security > User The admin user has access to create, modify or delete other accounts. Up to 15 user accounts can be created. Figure 10-1 User Information Add a User Steps: 1. Click to add a user. 2. Input the new User Name, select Level and input Password.
88 User Manual of Network Speed Dome Figure 10-2 Add a User Modify a User Steps: 1. Left-click to select the user from the list and click . 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions. 4. Click to finish the user modification. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
89 User Manual of Network Speed Dome Figure 10-3 Modify a User Delete a User Steps: 1. Left-click the user name you want to delete and click 2. Click . on the pop-up dialogue box to delete the user. Figure 10-4 Delete a User © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 90 10.2 Configuring RTSP Authentication Purpose: You can specifically secure the stream data of live view. Steps: 1. Enter the RTSP Authentication interface: Configuration> Advanced Configuration> Security > RTSP Authentication Figure 10-5 RTSP Authentication 2. Select the Authentication type basic or disable in the drop-down list to enable or disable the RTSP authentication. 3. Click to save the settings. 10.
User Manual of Network Speed Dome Figure 10-6 Device Information 10.4 Maintenance 10.4.1 Rebooting the Speed Dome Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance: 2. Click to reboot the network speed dome. Figure 10-7 Reboot the Device 10.4.2 Restoring Default Settings Steps: 1.
92 User Manual of Network Speed Dome 2. Click Note: Clicking or to restore the default settings. restores all the parameters to default settings including the IP address and user information. Please use this button with caution. Figure 10-8 Restore Default Settings 10.4.3 Importing/Exporting Configuration File Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance 2.
User Manual of Network Speed Dome 2. Click 93 to select the local upgrade file and then click to start remote upgrade. Note: The upgrading process will take 1 to 10 minutes. Please don't disconnect power of the speed dome during the process. The speed dome reboots automatically after upgrading. Figure 10-10 Remote Upgrade © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome 94 Chapter 11 Menu Tree Note: You may need to use the OSD(On Screen Display) menu when controlling the speed dome remotely. To display the OSD menu on the live view screen, you can call the preset number 95. The OSD menu tree is shown as follows: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
95 User Manual of Network Speed Dome Appendix Appendix 1 SADP Software Introduction Description of SADP SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool. It searches the active online devices within your subnet and displays the information of the devices. You can also modify the basic network information of the devices using this software.
96 User Manual of Network Speed Dome information; you can click to expand the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. Modify network parameters Steps: 1. Select the device to be modified in the device list and the network parameters of the device will be displayed in the Modify Network Parameters panel on the right side. 2. Edit the modifiable network parameters, e.g. IP address and port number. 3.
User Manual of Network Speed Dome 97 Appendix 2 Port Mapping The following settings are for TP-LINK router (TL-R410). The settings vary depending on different models of routers. Steps: 1. Select the WAN Connection Type, as shown below: Figure A.2.1 Select the WAN Connection Type 2. Set the LAN parameters of the router as in the following figure, including IP address and subnet mask settings. Figure A.2.2 Set the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding.
98 User Manual of Network Speed Dome Example: When the speed domes are connected to the same router, you can forward the ports of a speed dome as 80, 8000, 8200~8210 and 554 with IP address 192.168.1.23, and the ports of another speed dome as 81, 8001, 8201~8211 and 555 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, forward the port 80, 8000, 8200~8210 and 554 for the network speed dome at 192.168.1.23 2.
First Choice for Security Professionals
