TC-D2600BS SERIES HIGH SPEED DOME CAMERA USER’S MANUAL
11 Table Of Contents 1 Precautions…. ………………………………………………………… 2 2 Features……...………………………………………………………… 3 2.1 Built-in Decoder………………………………………………….. 3 2.2 Integrated Universal Speed Change Rotator………………… 3 2.3 Built-in High Definition Color Camera……………………….. 3 3 Technical Data……………………………………………………….… 4 3.1 Technical Parameters of the High-speed Dome…………… 4 3.2 Camera Parameter for High-speed Dome…………………… 4 4 Installation Guide…………….…………………………………….. 5 4.1 Installation Preparation…………………………………………. 5 4.
22 1 Precautions 1.Transportation Security No heavy stress, violent vibration or water splash are allowed during transportation, storage. The unit should be transported in separated packing. In shipments of distributor and delivery of maintenance, any damages caused by integral packing are not covered by warranty. 2. Installation Avoid heavy stress and violent vibration during installation. Don’t touch the dome cover directly by hand.
33 2 Features 2.
44 3 Technical Data 3.1 Technical Parameters of the High-speed Dome Model TC-2600BS High Speed Dome Power Supply AC24V/2.5A Operating Temperature -35 °C—60°C Operating moisture < 95% Power Consumption 50W Communication RS-485 bus, Communication transmission speed 2400/4800/9600BPS Protocols Pelco-D, Pelco-P Compatible 0.01°-180° /s 0.01° -120° /s +/- 0.07° 500° /s 360° Continuously 90° 364 x 350 x 202mm 5.
55 Video Output 1Vp-p75 ohms Back Light Auto Compensation Focus Auto/Manual Iris Auto/Manual S/N Ratio ≥50dB Electric 1/50~1/10 Shutter 000s 1/1~1/10000s 4 Installation Guide 4.1 Installation Preparation Video Coaxial Cables Mode Max Distance RG59/U 750ft(229m) RG6/U 1,000ft(305m) RG11/U 1,500ft(457m) 4.
66 4.3 Installation Size 4.4 Installation Procedures *Notice: The surface mount speed dome should be applied to hard ceiling. The wall must be thick enough to install the expansion screws and can bear 4 times the weight of the dome camera itself. (1) Open the reverse turning board on the base plate. Use the 3 holes on the bottom of the base plate as a location to bore 3 holes on the ceiling. (2) Bore 3 holes on the ceiling.
77 (3) Mount 3 expansion screws into the holes. (4) To lock the base plate to the dome housing, line up the A and B tabs on the dome body with the A and B label on the dome base. Push in on the tabs. Insert one side and then the other side. Continue pushing one the ends of the tabs until both sides click into place. Make sure the plug-in on the dome body is fully locked by the socket on the base plate.
88 (5) Match the 3 locators on the housing with the gaps one the plate and then turn the housing clockwise. Then pull down the housing lightly to check the firmness of installation. Then screw on the dome cover to the dome housing.
99 5 Settings 5.1 Interface 5.2 Dome Address, Transmission Speed, Protocol Setting Before the dome is installed, the communication protocol, baud rate and dome address, should be confirmed. Set the DIP switch, keeping the setting consistent with the control system. The relative DIP switch site and connecting wires are diagramed below for reference.
1010 *Notice: “1” means “on” status and “0” means “off” status.
1111 6 Preset Setting Speed dome camera supports 220 preset positions. The code numbers 1- 64 and 100-255 represent the 220 preset positions. You can activate some special functions by calling upon code number 65-99.
1212 Start sequence of group N Call upon 80 + call upon pp + call upon 98 Start setting preset position for sequence of group N Call upon 80 + call upon pp + set 84 + call upon qq+ … Stop setting preset position for the sequence of group N Call upon 96 Set standing time for the sequence of group N Call upon 80 + call upon pp + set 83 + call upon n Start pattern tour of group N Call upon 80 + call upon pp + call upon 97 Start setting pattern tour of group N Call upon 80 + call upon pp + set 86 S
1313 15 16 17 18 19 Display information Set 74 + call upon pp Set alarm triggering Set 76 + call upon pp Start alarm triggering Call upon 78 Stop alarm triggering Set 78 Open the alarm output “n” Call upon 80 + call upon n + call upon 70 Close the alarm “n” Call upon 80 + call upon n + set 70 Set privacy zone of group n Call upon 80 + call upon pp + set 71 Delete privacy zone of group n Call upon 80 + call upon pp + call upon71 Start privacy zone function Set 67 Close privacy zone fu
1414 7 The OSD Menu Setting 7.1 Operation Method of the Menu The user can call upon preset position 95 to enter the setting interface of the OSD menu. After entering the setting menu, a row of information will be displayed as follows (the screen can only show a single-step item of the following menu): The operations will be implemented by commands as “Focus in/out” and “Iris on/off”.
1515 7.
1616 MOTION MAIN MENU MOTION ―――――――――――――― ―――――――――――――― LANGUAGE: ENGLISH RESTART FACTORY DEFAULTS A B C D E F G BACK EXIT HELP EXIT A. PRESET PRESET ―――――――――――――― ―――――――――――――― PRESET NO.
1717 B.SCAN SCAN ―――――――――――――― ―――――――――――――― SCAN NO. : 01 TITLE : SCAN 1 START SCAN SPEED : 20 MOTION ―――――――――――――― A1 B1 C1 D1 E1 F1 BACK EXIT BACK EXIT A1.SCAN NO. Move the cursor to SCAN NO. and press the key IRIS ON(key on control keyboard) to enter the edition mode of scan No., move the joystick upward and downward to select number. Then press IRIS ON to confirm. B1.
1818 C.SEQUENCE MOTION ―――――――――――――― SEQUENCE ―――――――――――――― SEQ NO. : 1 BACK EXIT BACK EXIT TITLE : SEQ 1 A1 B1 START DELETE C1 D1 E1 A1.SEQ NO. Move the cursor to SEQ NO. and press the key IRIS ON(key on control keyboard) to enter the edition mode of sequence No., move the joystick upward and downward to select number. Then press IRIS ON to confirm. B1.
1919 preset NO. you want to add in the sequence. c.When the < > is on the item INS, move the joystick upward and downward to select edition mode as “insert”, “ok” and “delete”. d. Press IRIS OFF to quit the edition. D. PATTERN MOTION ―――――――――――――― PATTERN ―――――――――――――― PATTERN NO. : 1 TITLE : PATTERN 1 START DELETE BACK EXIT A1 B1 C1 D1 E1 BACK EXIT A1.PATTERN NO.
2020 E. MOTION ―――――――――――――― ZONES ―――――――――――――― － ZONE IS NOT SET － ZONE NO. : 1 TITLE NO. : ZONE 1 DELETE BACK EXIT A1 B1 C1 D1 E1 F1 BACK EXIT A1.ZONE INFORMATION B1.ZONE NO. Move the cursor to ZONE NO. and press the key IRIS ON(key on control keyboard) to enter the edition mode of zone No., move the joystick upward and downward to select number. Then press IRIS ON to confirm. B1.
2121 F.TIMING ACTION A1 B1 MOTION ―――――――――――――― TIMING ACTION ―――――――――――――― C1 NO. START STOP MOTION 0 0 : 0 0 0 0 : 0 0 NONE 1 2 0 0 : 0 0 0 0 : 0 0 NONE 0 0 : 0 0 0 0 : 0 0 NONE 3 0 0 : 0 0 0 0 : 0 0 NONE 4 0 0 : 0 0 0 0 : 0 0 NONE 5 0 0 : 0 0 0 0 : 0 0 NONE 6 0 0 : 0 0 0 0 : 0 0 NONE 7 0 0 : 0 0 0 0 : 0 0 NONE 8 D1 MON COPY BACK G1 OFF F1 E1 A1.SHEDULE NO. B1.START Start time of timing action. C1.
2222 G. AUTO TRACKING MOTION ―――――――――――――― AUTO TRACKING ―――――――――――――― SENSITIVITY : 06 FRAME RATE: MID ENABLE: OFF A1 B1 C1 BACK EXIT A1.SENSITIVITY Secitivity of auto tracking funtion. Scale from1 to 15. B1.FRAME RATE Setting of the frame inspection rate. C1.ENABLE Enabel or disable the auto tracking function.
2323 A. IDLE ACTION DOME SETTINGS ―――――――――――――― IDLE ACTION ―――――――――――――― TIME : 3 0 SEC BACK EXIT EXIT ACTION : NO ACTION A1 B1 BACK A1：IDLE ACTION Move the cursor to TIME, press IRIS ON to enter the edition mode of idle action starting time. The time could be 30seconds, 2 minutes, 5 minutes or 10 minutes. Press IRIS ON to confirm.
2424 C1. ALARM MODE Move the cursor on ALARM MODE to set the current mode of alarm as ON, OFF and AUTO. D1. TRIGGER ACTION Move the cursor on TRIGGER ACTION to set the action type triggered by alarm, such as presets, sequence, pattern and scan. E1. ALARM OUT Move the cursor to ALARM OUT to select the alarm output channel. F1. CANCEL TIME Move the cursor to CANCEL TIME to set the duration of the alarm state. G1. START TIME START TIME means the time for opening the alarm when the alarm mode is auto. H1.
2525 D. PRIVACY MASK PRIVACY MASK ―――――――――――――― MASK NO. : 1 DOME SETTINGS ―――――――――――――― ENABLE : OFF DELETE A1 B1 C1 D1 BACK EXIT BACK EXIT A1. MASK NO. Move the cursor to MASK NO. to set the NO. of privacy mask zone. B1.ENABLE Move the cursor to ENABLE to enable or disable the privacy mask zone. C1. .Move the cursor to and press IRIS ON to enter the edition mode of privacy mask zone.
2626 A1：DATE Move the joystick leftward and rightward to select year, month and day. Move the joystick upward and downward to select the number. B1：TIME Move the joystick leftward and rightward to select hour and minute. Move the joystick upward and downward to select the number. F. PASSWORD PASSWORD ―――――――――――――― DOME SETTINGS ―――――――――――――― A1 B1 ENABLE : OFF BACK EXIT BACK EXIT A1.
2727 B1. Move the cursor to CAPS. Press IRIS ON and move the joystick upward and downward to select capital and small letters. C1. ALPHABET Move the cursor to alphabet and press IRIS ON to select letters. H.
2828 CAMERA MAIN MENU CAMERA SETTING ―――――――――――――― AUTO FOCUS : OFF DIGITAL ZOOM : OFF BACKLIGHT : OFF IMAGE FREEZE : OFF ZOOM SPEED : LOW/ NORMAL/HIGH DAY NIGHT : AUTO/BW/COLOR ―――――――――――――― LANGUAGE: ENGLISH RESTART FACTORY DEFAULTS A B C D E F G BACK EXIT HELP EXIT A.AUTO FOCUS B.DIGITAL ZOOM C.BACKLIGHT When the light is dim, please open the backlight compensation to make the image bright D.IMAGE FREEZE E.
2929 8 Trouble Shooting Problems Possible Reason Solution Power on, no movement, no image, indicator light does not light Power line connected wrong Correct it Power damaged Replace Blowout Replace Power line be connected bad Check it The machine’s address code or baud rate is wrong Reset Protocol wrong Correct it RS485 bus be connected wrong Check it Focus in manual state Clean it Dome is dirty Change a certified power supply Fan is connected wrong Check it Power on, self check, ha
