Specifications

ManualsBrandsDatacom ManualsNetworkingDM4000 Series

DM4000 Series - Installation and

Operation Guide

204.0112.10

Summary of content (118 pages)

PAGE 1
DM4000 Series - Installation and Operation Guide 204.0112.
PAGE 2
Revision History Revision 10 2010/10/18 New interface boards included Revision 09 2010/01/21 New interface boards included Revision 08 2009/09/24 New pictures included Revision 07 2009/05/19 SFP pictures and new interface boards included Revision 06 2008/12/02 New pictures included Revision 05 2008/06/24 Transceivers homologation check included Revision 04 2008/01/23 CE mark information and new pictures included Revision 03 2008/01/15 Power supply connectors information included Revision 02 2007/11/21 Gener
PAGE 3
Warranty This product is guaranteed to be free against manufacturing and raw material defects, during the period specified in the sales receipt. The warranty includes only the repair and replacement of components or defective parts, free of charge.
PAGE 4
Contact Information In order to contact the DATACOM technical support, or sales department: • • • Support: • E-mail: suporte@datacom.ind.br • Phone: +55 51 3358-0122 • Fax: +55 51 3358-0101 Sales: • E-mail: comercial@datacom.ind.br • Phone: +55 51 3358-0100 • Fax: +55 51 3358-0101 Internet: • • www.datacom.ind.br Address: • DATACOM • Av.
PAGE 5
Conventions General Information: Symbol Description Notes give an explanation about some topic in the foregoing paragraph.
PAGE 6
Table of Contents 1. General Recommendation.....................................................................................................................1 1.1. Before the Installation .................................................................................................................1 2. Introduction............................................................................................................................................3 2.1. About this guide ...........................
PAGE 7
9. DM4000 MPU416.................................................................................................................................34 9.1. Overview ...................................................................................................................................34 9.2. Front Panel Description.............................................................................................................35 9.3. System Status LEDs.....................................................
PAGE 8
15.4.1. Software......................................................................................................................60 15.4.2. Hardware ....................................................................................................................60 16. DM4000 ETH48GT ...........................................................................................................................62 16.1. Overview ...............................................................................
PAGE 9
23. DM4000 GPC-DCM ..........................................................................................................................86 23.1. Overview .................................................................................................................................86 23.2. Front Panel Description...........................................................................................................87 24. Fan Board ....................................................................
PAGE 10
List of Tables 3-1. Recommended Power Limits and Consumption Parameters for DM4001 ..........................................7 3-2. Absolute Power Limits for DM4001..................................................................................................?? 3-3. Recommended Power Limits and Consumption Parameters for DM4004 ..........................................8 3-4. Absolute Power Limits for DM4004..................................................................................................
PAGE 11
21-2. DM4000 GPC-OAB Port Status LEDs ............................................................................................83 22-1. Pre-amplifier parameters ..................................................................................................................85 22-2. DM4000 GPC-OAP Port Status LEDs.............................................................................................85 23-1. DCM parameters .............................................................................
PAGE 12
Chapter 1. General Recommendation 1.1. Before the Installation "Before the installation, read the entire manual attentively." "The installation of any electric equipment must be in accordance with the current law in the place where this equipment will be installed. This includes adequate devices of protection, sizing and protection to the capacities of the equipment." "Always observe the instructions of security during the installation, operation or maintenance of this product.
PAGE 13
Chapter 1. General Recommendation "Some equipment in this manual have laser emitting optical modules. Avoid the exposure to eyes and skin." "WEEE Directive Symbol (Applicable in the European Union and other European countries with separate collection systems).This symbol on the product or its packaging indicates that this product must not be disposed of with other waste.
PAGE 14
Chapter 2. Introduction 2.1. About this guide This guide can be used for all DATACOM DM4000 Metro Ethernet Series, providing information about installation and characteristics of the DM4000 family. This guide focuses on the physical, electrical, status indications and installation portion of the hardware. It is assumed that the individual or individuals managing any aspect of this product have basic understanding of Switching, Routing, Ethernet, and general Telecommunications. 2.2. Overview Figure 2-1.
PAGE 15
Chapter 2. Introduction can be used to connect to clients, servers or access devices (hubs, routers, LAN switches or WAN access devices). DM4000 Metro Ethernet Series provides multiple chassis options to connect and manage non-blocking data between boards. Its scalable platform design allows future growth and investment protection from the smallest to the largest chassis option.
PAGE 16
Chapter 2. Introduction • DM4000 ETH2x10GX H Series - Hot swappable 2 ports 10 Gigabit XFP interface board. • DM4000 ETH24GT - Hot swappable 24 ports 10/100/1000Base-T Ethernet switch interface board. • DM4000 ETH48GT - Hot swappable 48 ports 10/100/1000Base-T Ethernet switch interface board. • DM4000 ETH48GX H Series - Hot swappable 48 ports SFP Gigabit Ethernet switch interface board. SFPs are 100Base-FX, 1000Base-X and SGMII compatible.
PAGE 17
Chapter 2. Introduction • DM4000 ETH12GX+1x10GX using a MPU192 in a DM4008 Chassis Different MPUs cannot be used in the same chassis.
PAGE 18
Chapter 3. Technical Specifications 3.1. Environmental Conditions Operating Temperature: 0 to 55 degrees Celsius Storage Temperature: -20 to 65 degrees Celsius Humidity: 10 to 90% non condensing 3.2. Power Supply The DM4000 family has a DC power input range of -48 to -60 V WARNING: "Before connecting any cable to the equipment, be sure that the grounding system is functional.
PAGE 19
Chapter 3. Technical Specifications Table 3-2. Absolute Power Limits for DM4001 Absolute Voltage Limits min. max. -36V -72V Power Type Power max. Current max. DC 200W 4.7A Follow Power information below screws to correct RET / -48V connections Figure 3-1. DM4001 Power Supplies Connectors 3.2.2. DM4004 Table 3-3. Recommended Power Limits and Consumption Parameters for DM4004 Rec. Voltage Limits min. max. -48V -60V Power Type Power max. Current max. DC 576W 12.00A Power Type Power max.
PAGE 20
Chapter 3. Technical Specifications Figure 3-2. DM4004 Power Supplies Connectors 3.2.3. DM4008 Table 3-5. Recommended Power Limits and Consumption Parameters for DM4008 Rec. Voltage Limits min. max. -48V -60V Power Type Power max. Current max. DC 1200W 25.00A Power Type Power max. Current max. DC 1200W 33.33A Table 3-6. Absolute Power Limits for DM4008 Absolute Voltage Limits min. max. -36V -72V Figure 3-3. DM4008 Power Supplies Connectors 3.2.4. Interface Modules Table 3-7.
PAGE 21
Chapter 3. Technical Specifications Interface Module Fuse Consumption ETH2x10GX 3.15A fuse, type T (delay), 250V 70W ETH2x10GX H Series 3.15A fuse, type T (delay), 250V 70W ETH24GT 3.15A fuse, type T (delay), 250V 55W ETH48GT 3.15A fuse, type T (delay), 250V 110W ETH48GX H Series 3.15A fuse, type T (delay), 250V 85W ETH4x10GX H Series 3.15A fuse, type T (delay), 250V 70W MPU192 3.15A fuse, type T (delay), 250V 20W MPU384 3.15A fuse, type T (delay), 250V 30W MPU416 3.
PAGE 22
Chapter 3. Technical Specifications FAN Kilograms (kg) Pounds (lbs) DM4004 19" 1.49 3.28 DM4004 23" 1.31 2.89 DM4008 2.68 5.90 Table 3-10. MPUs MPU Kilograms (kg) Pounds (lbs) MPU192 0.97 2.13 MPU384 1.12 2.47 MPU416 1.12 2.47 Interface Board Kilograms (kg) Pounds (lbs) ETH24GX 2.49 5.49 ETH24GX H Series 2.49 5.49 ETH12GX 2.30 5.07 ETH12GX+1x10GX 2.39 5.27 ETH24GX+2x10GX H Series 2.74 6.03 ETH2x10GX 2.35 5.17 ETH2x10GX H Series 2.35 5.17 ETH24GT 2.49 5.
PAGE 23
Chapter 3. Technical Specifications Panel Kilograms (kg) Pounds (lbs) Interface Boards Blank Panel 2.68 5.90 MPUs Blank Panel 0.09 0.19 GPCs Blank Panel 0.05 0.
PAGE 24
Chapter 4. DM4001 Chassis 4.1. Overview The DM4001 chassis is compatible with all interface boards of the DM4000 Series, allowing their utilization as a standalone version. Its backplane interface allows non-blocking wire speed data of all interface boards connected. Each interface board has temperature sensors that allow DM4001 chassis electronic fan control to manage fan speed increasing equipment reliability and minimizing fan noise. Figure 4-1.
PAGE 25
Chapter 4. DM4001 Chassis 4.2. Front Panel Description The Front Panel of the DM4001 chassis has a RS232 Console port, an Ethernet Outband Management interface and Status LEDs. Figure 4-2. DM4001 Chassis - Front Panel 4.3. System Status LEDs The System Status LEDs on the front panel can be used to monitor system activity. The following figure shows where the LEDs are located and the table below indicates the system status according to each LEDs condition. Figure 4-3.
PAGE 26
Chapter 4. DM4001 Chassis Table 4-1. System LEDs DM4001 Chassis LED Power Fail Link/Act Speed CONDITION STATUS ON Equipment on. OFF Equipment off. ON Indicates fail (high temperature or fan fail). OFF Equipment operates normally. ON/Blinking Connected with link up. Blinking indicates activity. OFF No connection established. ON 10Mbit/s connection established. OFF Indicates a 100Mbit/s Connection when Link/Act LED is ON or Blinking. 4.4.
PAGE 27
Chapter 4. DM4001 Chassis Table 4-2. Interface Pinout Management Port RJ-45 Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- 4,5,7,8 - RJ-45 Serial Port 1,2,7,8 - 3 Tx 4,5 GND 6 Rx 4.5. Rear Panel Description The Rear Panel of the DM4001 chassis has two 48 to 60V DC power inputs. Figure 4-5. DM4001 Rear Panel Note: The figure above represents the last version of Rear Panel, another version could be different. For your safety read the power indication.
PAGE 28
Chapter 5. DM4004 Chassis 5.1. Overview The DM4004 chassis is compatible with all MPUs and interface boards of the DM4000 Series. It is available in two versions: for use in 19" and 23" racks. The 19" chassis is the standard version while the 23" has a better temperature perfomance and a dust filter option. Both versions have a backplane that can handle up to 384Gbps of non-blocking data. They have four interface board slots, two MPU slots, two general purpose slots and one FAN module slot. Figure 5-1.
PAGE 29
Chapter 5. DM4004 Chassis Figure 5-2. DM4004 Chassis 23" For normal operation blank panels are required for non slotted interface boards and MPUs. 5.2. Front Panel Description The main power input connectors are located in the Front Panel of DM4004 chassis. It supports dual redundant DC inputs for 48V DC nominal operation.
PAGE 30
Chapter 5. DM4004 Chassis Figure 5-3. DM4004 Chassis 19" - Front Panel Figure 5-4. DM4004 Chassis 23" - Front Panel 5.3. Rear Panel Description The DM4004 chassis Rear Panel has one console DB9 connector.
PAGE 31
Chapter 5. DM4004 Chassis Figure 5-5. DM4004 Chassis 19" - Rear Panel Figure 5-6. DM4004 Chassis 23" - Rear Panel 5.4. Console Management Port The chassis contains one DB9 connector on its rear panel. The connector has two Console ports, each one connected to each MPU. The pinouts of the Console ports are shown in the following figure and table.
PAGE 32
Chapter 5. DM4004 Chassis Figure 5-7. DB9 Pins Specification Table 5-1.
PAGE 33
Chapter 6. DM4008 Chassis 6.1. Overview The DM4008 chassis is compatible with all MPUs and interface boards of the DM4000 Series. It has eight interface board slots, two MPU slots, two multipurpose slots and one FAN module slot. Figure 6-1.
PAGE 34
Chapter 6. DM4008 Chassis 6.2. Front Panel Description The main power input connectors are located in the Front Panel of DM4008 chassis. It supports dual redundant DC inputs for 48V DC nominal operation. Figure 6-2. DM4008 Chassis - Front Panel 6.3. Rear Panel Description The DM4008 chassis Rear Panel has one console DB9 connector.
PAGE 35
Chapter 6. DM4008 Chassis Figure 6-3. DM4008 Chassis - Rear Panel 6.4. Console Management Port The chassis contains one DB9 connector on its rear panel. The connector has two Console ports, each one connected to each MPU. The pinouts of the Console ports are shown in the following figure and table. Figure 6-4.
PAGE 36
Chapter 6. DM4008 Chassis Table 6-1.
PAGE 37
Chapter 7. DM4000 MPU192 7.1. Overview The DM4000 MPU192 is a hot-swappable Switch Fabric module capable of handling 192Gbps of nonblocking data (up to 96 Gigabit Ethernet ports). It is compatible with DM4004 and DM4008 chassis. In the DM4004 chassis it can handle up to 24 Gigabit ports per interface module at a non blocking configuration. In the DM4008 it can handle up to 12 Gigabit Ethernet ports per interface module board at a non-blocking configuration.
PAGE 38
Chapter 7. DM4000 MPU192 CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 7.2. Front Panel Description The DM4000 MPU192 Front Panel has system status LEDs, one Ethernet Outband Management port (MGMT ETH), one RS-232 Serial port (Console) and one Auxiliar port (AUX). Figure 7-2.
PAGE 39
Chapter 7. DM4000 MPU192 7.3. System Status LEDs The DM4000 MPU192 has 9 system status LEDs monitoring CPU utilization, Ethernet outband, system fails and active MPU status. Figure 7-3. DM4000 MPU192 - Front Panel LEDs Table 7-1. MPU192 System LEDs LED ACT MPU FAIL CPU UTILIZATION 100 M Link Act CONDITION STATUS ON MPU active. OFF MPU inactive. ON Hardware failure. OFF Hardware is functional. ON 20% utilization. ON 40% utilization. ON 60% utilization. ON 80% utilization.
PAGE 40
Chapter 7. DM4000 MPU192 The pinouts of both Console and Outband Management ports are shown in the table below. Figure 7-4. DM4000 MPU192 - Front Panel Connectors Table 7-2.
PAGE 41
Chapter 8. DM4000 MPU384 8.1. Overview The DM4000 MPU384 is a hot-swappable Switch Fabric module capable of handling 384Gbps of nonblocking data (up to 192 Gigabit Ethernet ports). It is compatible with DM4004 and DM4008 chassis. In the DM4004 chassis it can handle up to 48 Gigabit Ethernet ports per interface board at a non-blocking configuration. In the DM4008 it can handle up to 24 Gigabit Ethernet ports per interface board.
PAGE 42
Chapter 8. DM4000 MPU384 CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 8.2. Front Panel Description The DM4000 MPU384 Front Panel has system status LEDs, one Ethernet Outband Management port (MGMT ETH), one RS-232 Serial port (Console) and one Auxiliar port (AUX). Figure 8-2.
PAGE 43
Chapter 8. DM4000 MPU384 8.3. System Status LEDs The DM4000 MPU384 has 9 system status LEDs monitoring CPU utilization, Ethernet outband, system fails and active MPU status. Figure 8-3. DM4000 MPU384 - Front Panel LEDs Table 8-1. MPU384 System LEDs LED ACT MPU FAIL CPU UTILIZATION 100 M Link Act CONDITION STATUS ON MPU active. OFF MPU inactive. ON Hardware failure. OFF Hardware is functional. ON 20% utilization. ON 40% utilization. ON 60% utilization. ON 80% utilization.
PAGE 44
Chapter 8. DM4000 MPU384 The pinouts of both Console and Outband Management ports are shown in the table below. Figure 8-4. DM4000 MPU384 - Front Panel Connectors Table 8-2.
PAGE 45
Chapter 9. DM4000 MPU416 9.1. Overview The DM4000 MPU416 is a hot-swappable Switch Fabric module capable of handling 416Gbps of nonblocking data (up to 208 Gigabit Ethernet ports). It is compatible with DM4004 and DM4008 chassis. In the DM4004 chassis it can handle up to 52 Gigabit Ethernet ports per interface board at a non-blocking configuration. In the DM4008 it can handle up to 26 Gigabit Ethernet ports per interface board.
PAGE 46
Chapter 9. DM4000 MPU416 CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 9.2. Front Panel Description The DM4000 MPU416 Front Panel has system status LEDs, one Ethernet Outband Management port (MGMT ETH), one RS-232 Serial port (Console) and one Auxiliar port (AUX). Figure 9-2.
PAGE 47
Chapter 9. DM4000 MPU416 9.3. System Status LEDs The DM4000 MPU416 has 9 system status LEDs monitoring CPU utilization, Ethernet outband, system fails and active MPU status. Figure 9-3. DM4000 MPU416 - Front Panel LEDs Table 9-1. MPU416 System LEDs LED ACT MPU FAIL CPU UTILIZATION 100 M Link Act CONDITION STATUS ON MPU active. OFF MPU inactive. ON Hardware failure. OFF Hardware is functional. ON 20% utilization. ON 40% utilization. ON 60% utilization. ON 80% utilization.
PAGE 48
Chapter 9. DM4000 MPU416 The pinouts of both Console and Outband Management ports are shown in the table below. Figure 9-4. DM4000 MPU416 - Front Panel Connectors Table 9-2.
PAGE 49
Chapter 10. DM4000 ETH24GX 10.1. Overview The DM4000 ETH24GX is a non-blocking 24 SFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH24GX can handle up to 35,714,285 packets per second supporting 9600 bytes jumbo frames and has an internal 256MB Switching Memory supporting wire speed operation. The DM4000 ETH24GX has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash.
PAGE 50
Chapter 10. DM4000 ETH24GX CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 10.2. Front Panel Description DM4000 ETH24GX front panel contains 24 SFP slots and port status LEDs. Figure 10-2. DM4000 ETH24GX - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes.
PAGE 51
Chapter 10. DM4000 ETH24GX 10.3. System Status LEDs The DM4000 ETH24GX has the following port status LEDs. Figure 10-3. DM4000 ETH24GX - Front Panel LEDs Table 10-1. ETH24GX Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. Orange Indicates that a 10/100Mbps connection was established. Green Indicates that a 1000Mbps connection was established. 10.4. Software and Hardware Features 10.
PAGE 52
Chapter 10. DM4000 ETH24GX 10.4.2. Hardware Table 10-2.
PAGE 53
Chapter 11. DM4000 ETH24GX H Series 11.1. Overview The DM4000 ETH24GX H Series is a non-blocking 24 SFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH24GX H Series can handle up to 35,714,285 packets per second supporting 12K jumbo frames and has an internal 4MB Switching Memory supporting wire speed operation. The DM4000 ETH24GX H Series has a 1GHz microprocessor with 1GB of RAM and 1GB of Flash.
PAGE 54
Chapter 11. DM4000 ETH24GX H Series 11.2. Front Panel Description DM4000 ETH24GX H Series front panel contains 24 SFP slots and port status LEDs. Figure 11-2. DM4000 ETH24GX H Series - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes." WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on the equipment.
PAGE 55
Chapter 11. DM4000 ETH24GX H Series 11.3. System Status LEDs The DM4000 ETH24GX H Series has the following port status LEDs. Table 11-1. ETH24GX H Series Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that a 10/100Mbps connection was established. OFF Indicates that a 1000Mbps connection was established. 11.4. Software and Hardware Features 11.4.1.
PAGE 56
Chapter 11. DM4000 ETH24GX H Series 11.4.2. Hardware Table 11-2.
PAGE 57
Chapter 12. DM4000 ETH12GX 12.1. Overview The DM4000 ETH12GX is a non-blocking 12 SFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH12GX can handle up to 17,857,142 packets per second supporting 9600 bytes jumbo frames and has an internal 128MB Switching Memory supporting wire speed operation. The DM4000 ETH12GX has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash.
PAGE 58
Chapter 12. DM4000 ETH12GX CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 12.2. Front Panel Description DM4000 ETH12GX front panel contains 12 SFP ports and port status LEDs. Figure 12-2. DM4000 ETH12GX - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes.
PAGE 59
Chapter 12. DM4000 ETH12GX 12.3. System Status LEDs The DM4000 ETH12GX has the following port status LEDs. Figure 12-3. DM4000 ETH12GX - Front Panel LEDs Table 12-1. ETH12GX Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. Orange Indicates that a 10/100Mbps connection was established. Green Indicates that a 1000Mbps connection was established. 12.4. Software and Hardware Features 12.
PAGE 60
Chapter 12. DM4000 ETH12GX 12.4.2. Hardware Table 12-2.
PAGE 61
Chapter 13. DM4000 ETH12GX+1x10GX 13.1. Overview The DM4000 ETH12GX+1x10GX is a non-blocking 12 SFP port plus one 10 Gigabit XFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH12GX+1x10GX can handle up to 32,738,095 packets per second supporting 9600 bytes jumbo frames and has an internal 256MB Switching Memory supporting wire speed operation. The DM4000 ETH12GX+1x10GX has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash.
PAGE 62
Chapter 13. DM4000 ETH12GX+1x10GX CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 13.2. Front Panel Description DM4000 ETH12GX+1x10GX front panel contains 12 SFP ports, 1 XFP port and port status LEDs. Figure 13-2.
PAGE 63
Chapter 13. DM4000 ETH12GX+1x10GX 13.3. System Status LEDs The DM4000 ETH12GX+1x10GX has the following port status LEDs. Figure 13-3. DM4000 ETH12GX+1x10GX - Front Panel LEDs Table 13-1. ETH12GX+1x10GX Port Status LEDs LED Link/Act 10/100/1000 Laser TX On CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that a 10/100Mbps connection was established. OFF Indicates that a 1000Mbps connection was established.
PAGE 64
Chapter 13. DM4000 ETH12GX+1x10GX 13.4.2. Hardware Table 13-2.
PAGE 65
Chapter 14. DM4000 ETH2x10GX 14.1. Overview The DM4000 ETH2x10GX is a non-blocking two 10 Gigabit XFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH2x10GX can handle up to 29,761,904 packets per second supporting 9600 bytes jumbo frames and has an internal 256MB Switching Memory supporting wire speed operation. The DM4000 ETH2x10GX has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash.
PAGE 66
Chapter 14. DM4000 ETH2x10GX CAUTION: "Risk of explosion if battery is replaced by an incorrect type. Use only cell type CR2032. Dispose of used batteries according with local regulations." 14.2. Front Panel Description DM4000 ETH2x10GX front panel contains 2 XFP ports and port status LEDs. Figure 14-2. DM4000 ETH2x10GX - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes.
PAGE 67
Chapter 14. DM4000 ETH2x10GX 14.3. System Status LEDs The DM4000 ETH2x10GX has the following port status LEDs. Figure 14-3. DM4000 ETH2x10GX - Front Panel LEDs Table 14-1. ETH2x10GX Port Status LEDs LED Link/Act Laser TX On CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that XFP TX laser is on. OFF Indicates that XFP TX laser is off. 14.4. Software and Hardware Features 14.4.1.
PAGE 68
Chapter 14. DM4000 ETH2x10GX 14.4.2. Hardware Table 14-2.
PAGE 69
Chapter 15. DM4000 ETH24GT 15.1. Overview The DM4000 ETH24GT is a non-blocking 24 10/100/1000Mbps port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH24GT can handle up to 35,714,285 packets per second supporting 9500 bytes jumbo frames reaching wire speed operation. The DM4000 ETH24GT has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash. The DM4000 ETH24GT extensive Metro support can handle up to 16,000 MACs. Figure 15-1.
PAGE 70
Chapter 15. DM4000 ETH24GT 15.2. Front Panel Description The ETH24GT front panel contains 24 RJ45 ports and port status LEDs. With option to have PoE in all ports. Figure 15-2. DM4000 ETH24GT - Front Panel WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on equipment." WARNING: "This interface board supports a 3.15A fuse, type T (delay), 250V. If necessary, replace it only for another one of the same type and value.
PAGE 71
Chapter 15. DM4000 ETH24GT 15.3. System Status LEDs The DM4000 ETH24GT has the following port status LEDs: Table 15-1. ETH24GT Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. Orange Indicates that a 10/100Mbps connection was established. Green Indicates that a 1000Mbps connection was established. 15.4. Software and Hardware Features 15.4.1.
PAGE 72
Chapter 15. DM4000 ETH24GT 15.4.2. Hardware Table 15-2.
PAGE 73
Chapter 16. DM4000 ETH48GT 16.1. Overview The DM4000 ETH48GT is a non-blocking 48 10/100/1000Mbps port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH48GT can handle up to 71,428,571 packets per second supporting 9500 bytes jumbo frames reaching wire speed operation. The DM4000 ETH48GT has a 400MHz microprocessor with 256MB of RAM and 64MB of Flash. The DM4000 ETH48GT extensive Metro support can handle up to 16,000 MACs.
PAGE 74
Chapter 16. DM4000 ETH48GT 16.2. Front Panel Description The ETH48GT front panel contains 48 RJ45 ports and port status LEDs. With option to have PoE in all ports. Figure 16-2. DM4000 ETH48GT- Front Panel WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on equipment." WARNING: "This interface board supports a 3.15A fuse, type T (delay), 250V. If necessary, replace it only for another one of the same type and value.
PAGE 75
Chapter 16. DM4000 ETH48GT 16.3. System Status LEDs The DM4000 ETH48GT has the following port status LEDs: Table 16-1. ETH48GT Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. Orange Indicates that a 10/100Mbps connection was established. Green Indicates that a 1000Mbps connection was established. 16.4. Software and Hardware Features 16.4.1.
PAGE 76
Chapter 16. DM4000 ETH48GT 16.4.2. Hardware Table 16-2.
PAGE 77
Chapter 17. DM4000 ETH48GX H Series 17.1. Overview The DM4000 ETH48GX H Series is a non-blocking 48 SFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH84GX H Series can handle up to 71,428,571 packets per second supporting 12KB jumbo frames and has an internal 4MB Switching Memory supporting wire speed operation. The DM4000 ETH48GX H Series has a 1GHz microprocessor with 1GB of RAM and 1GB of Flash.
PAGE 78
Chapter 17. DM4000 ETH48GX H Series 17.2. Front Panel Description DM4000 ETH48GX H Series front panel contains 48 SFP slots and port status LEDs. Figure 17-2. DM4000 ETH48GX H Series - Front Panel WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on equipment." WARNING: "This interface board supports a 5A fuse, type T (delay), 250V. If necessary, replace it only for another one of the same type and value.
PAGE 79
Chapter 17. DM4000 ETH48GX H Series 17.3. System Status LEDs The DM4000 ETH48GX H Series has the following port status LEDs: Table 17-1. ETH48GX H Series Port Status LEDs LED Link/Act 10/100/1000 CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. Orange Indicates that a 10/100Mbps connection was established. Green Indicates that a 1000Mbps connection was established. 17.4. Software and Hardware Features 17.4.1.
PAGE 80
Chapter 17. DM4000 ETH48GX H Series 17.4.2. Hardware Table 17-2.
PAGE 81
Chapter 18. DM4000 ETH24GX+2x10GX H Series 18.1. Overview The DM4000 ETH24GX+2x10GX H Series is a non-blocking 24 SFP port plus two 10 Gigabit XFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH24GX+2x10GX H Series can handle up to 65,476,190 packets per second supporting 12KB jumbo frames and has an internal 4MB Switching Memory supporting wire speed operation. The DM4000 ETH24GX+2x10GX H Series has a 1GHz microprocessor with 1GB of RAM and 1GB of Flash.
PAGE 82
Chapter 18. DM4000 ETH24GX+2x10GX H Series 18.2. Front Panel Description DM4000 ETH24GX+2x10GX front panel contains 24 SFP ports, 2 XFPs port and port status LEDs. Figure 18-2. DM4000 ETH24GX+2x10GX H Series - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes." WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on the equipment.
PAGE 83
Chapter 18. DM4000 ETH24GX+2x10GX H Series 18.3. System Status LEDs The DM4000 ETH24GX+2x10GX H Series has the following port status LEDs. Table 18-1. ETH24GX+2x10GX H Series Port Status LEDs LED Link/Act 10/100/1000 Laser TX On CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that a 10/100Mbps connection was established. OFF Indicates that a 1000Mbps connection was established.
PAGE 84
Chapter 18. DM4000 ETH24GX+2x10GX H Series 18.4.2. Hardware Table 18-2.
PAGE 85
Chapter 19. DM4000 ETH2x10GX H Series 19.1. Overview The DM4000 ETH2x10GX H Series is a non-blocking two 10 Gigabit XFP port interface board compatible with DM4001, DM4004 and DM4008 chassis. The DM4000 ETH2x10GX H Series can handle up to 29,761,904 packets per second supporting 12KB jumbo frames and has an internal 4MB Switching Memory supporting wire speed operation. The DM4000 ETH2x10GX H Series has a 1GHz microprocessor with 1GB of RAM and 1GB of Flash.
PAGE 86
Chapter 19. DM4000 ETH2x10GX H Series 19.2. Front Panel Description DM4000 ETH2x10GX front panel contains 2 XFPs port and port status LEDs. Figure 19-2. DM4000 ETH2x10GX H Series - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes." WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on the equipment.
PAGE 87
Chapter 19. DM4000 ETH2x10GX H Series 19.3. System Status LEDs The DM4000 ETH2x10GX H Series has the following port status LEDs. Table 19-1. ETH2x10GX H Series Port Status LEDs LED Link/Act Laser TX On CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that XFP TX laser is on. OFF Indicates that XFP TX laser is off. 19.4. Software and Hardware Features 19.4.1.
PAGE 88
Chapter 19. DM4000 ETH2x10GX H Series 19.4.2. Hardware Table 19-2.
PAGE 89
Chapter 20. DM4000 ETH4x10GX H Series 20.1. Overview The DM4000 ETH4x10GX H Series is a non-blocking four 10 Gigabit XFP port interface board compatible with DM4001, DM4004 and DM4008 chassis The DM4000 ETH4x10GX H Series can handle up to 59,523,808 packets per second supporting 12KB jumbo frames and has an internal 4MB Switching Memory supporting wire speed operation. The DM4000 ETH4x10GX H Series has a 1GHz microprocessor with 1GB of RAM and 1GB of Flash.
PAGE 90
Chapter 20. DM4000 ETH4x10GX H Series 20.2. Front Panel Description DM4000 ETH4x10GX H Series front panel contains 4 XFPs port and port status LEDs. Figure 20-2. DM4000 ETH4x10GX H Series - Front Panel WARNING: "When performing installation and maintenance operations of optical fibers, you should not stand close or look directly into the fiber outlet with unaided eyes." WARNING: "Electrostatic generated by human body may damage the electrostatic sensitive components on the equipment.
PAGE 91
Chapter 20. DM4000 ETH4x10GX H Series 20.3. System Status LEDs The DM4000 ETH4x10GX H Series has the following port status LEDs. Table 20-1. ETH4x10GX H Series Port Status LEDs LED Link/Act 10/100/1000 Laser TX On CONDITION STATUS ON/Blinking Connection established. Blinking indicates port activity. OFF No connection established. ON Indicates that a 10/100Mbps connection was established. OFF Indicates that a 1000Mbps connection was established. ON Indicates that XFP TX laser is on.
PAGE 92
Chapter 20. DM4000 ETH4x10GX H Series 20.4.2. Hardware Table 20-2.
PAGE 93
Chapter 21. DM4000 GPC-OAB 21.1. Overview DM4000 GPC-OAB is an active booster amplifier based on erbium doped fiber (EDF). The module amplifies optical signals, allowing extension of optical loop up to 10 Gbit/s. Booster’s output power can be configured through terminal, management system or locally. It can be managed by host equipment or directly. If the configuration jumper is on "AUTO" position, front serial interface is disabled and the configuration is executed by equipment.
PAGE 94
Chapter 21. DM4000 GPC-OAB CAUTION: "Amplification module uses transmitters with no-visible class 3B laser radiation. Never look directly to the laser terminals or to the optical fiber. The exposure to the laser emission can cause total or partial loss of vision." Parameters from DM4000 GPC-OAB Table 21-1. Booster parameters Parameters Minimum Typical value Maximum Unit Wave length 1530 - 1562 nm Input power -10 - +2 dBm Output power - - +15 dBm Noise figure - - 8 dB PDG - - 0.
PAGE 95
Chapter 22. DM4000 GPC-OAP 22.1. Overview DM4000 GPC-OAP is an active pre-amplifier based on erbium doped fiber (EDF). The module amplifies attenuated optical signals, making possible its detection by receptor. DM4000 GPC-OAP allows extension of optical loop up to 10 Gbit/s. It can be managed by host equipment or directly. If the configuration jumper is on "AUTO" position, front serial interface is disabled and the configuration is executed by equipment.
PAGE 96
Chapter 22. DM4000 GPC-OAP CAUTION: "Amplification module uses transmitters with no-visible class 3B laser radiation. Never look directly to the laser terminals or to the optical fiber. The exposure to the laser emission can cause total or partial loss of vision." Parameters from DM4000 GPC-OAP Table 22-1. Pre-amplifier parameters Parameters Minimum Typical value Maximum Unit Wave length - 1550.
PAGE 97
Chapter 23. DM4000 GPC-DCM 23.1. Overview DM4000 GPC-DCM is an Dispersion-compensating Module. The module compensates 40 km of the dispersion of the fiber being used in a transmission system. Its optimized for use in Nondispersion-Shifted Fiber (ITU-T G.652). The DM4000 GPC-DCM is a passive module and do not need to be powered to work. The DM4000 GPC-DCM is designed to work with Transceivers that are design for DWDM, the Dispersion Level is not guaranteed for lambdas outside ITU-T DWDM Grid. Figure 23-1.
PAGE 98
Chapter 23. DM4000 GPC-DCM Parameters from DM4000 GPC-DCM Table 23-1. DCM parameters Parameter Value Unit First Channel 1527.216 nm 196.3 THz Last Channel 1567.133 nm 191.3 THz Channel Spacing 100 GHz Operation Bandwidth ITU ± 17.5 GHz Insertion Loss <4 dB Dispersion Level -665 * ps/nm Return Loss > 40 dB Polarization Dependent Loss < 0.
PAGE 99
Chapter 24. Fan Board 24.1. Description The FAN module is used to avoid high temperature inside the equipment that may cause malfunction. The FAN module is hot swappable. It can be replaced while the switch is active if necessary. But for safety reasons, it is recommended to be done with the chassis turned off. WARNING: "Don’t block FAN module airflow. Keep vents open and unobstructed." WARNING: "Don’t put your hands near to FAN module while the equipment is on.
PAGE 100
Chapter 24. Fan Board Figure 24-2. DM4008 FAN board without blank panels 24.2. Air Flow The next figures show how the air flows inside DM4004 and DM4008 Chassis. 24.2.1. DM4004 and DM4008 Chassis Figure 24-3.
PAGE 101
Chapter 24. Fan Board Figure 24-4. Air flow inside DM4004 23" Figure 24-5.
PAGE 102
Chapter 25. Installation Guide WARNING: "Before touching the chassis, interface modules, MPUs or FAN modules a grounded electrostatic discharge (ESD) wrist strap should be used to prevent damage by the electrostatic contained in human body." You can find ESD wrist strap in installation kit. Look the following picture that shows how to put a ESD wrist strap in DM4004: Figure 25-1. ESD wrist strap 25.1.
PAGE 103
Chapter 25. Installation Guide - 1 console cable To install the switch in a rack, use the following procedure and refer to the figure below: Figure 25-2. Rack Mounting WARNING: "All slots that are not occupied with boards must be closed with a blank panel." 25.2. Powering the Switch WARNING: "Remember to attach the chassis to the ground before installing a power supply." Follow the picture below to connect the power cable to the chassis properly.
PAGE 104
Chapter 25. Installation Guide Figure 25-3. DM4001 Power Supply Connector Figure 25-4. DM4004/DM4008 Power Supply Connector WARNING: "Just use the plug included in installation kit." WARNING: "The plug is the disconnection device on the equipment. The power outlet where the supply cable is connected must be positioned near the equipment and have easy access.
PAGE 105
Chapter 25. Installation Guide WARNING: "Consult the table about the type of fuse used in each interface module. If necessary, replace it only for another one of the same type and value." 25.2.1. Cables Table 25-1. Cable dimension according chassis Chassis Current max. Minimum conductor sizes Nominal cross-sectional area AWG [cross-sectional area in mm2] DM4001 2,5A 1,5mm2 14 [2 mm2] DM4004 12,5A 2,5mm2 12 [3 mm2] DM4008 22A 4mm2 10 [5 mm2] 25.2.1.1.
PAGE 106
Chapter 25. Installation Guide To build the cable, solder a female pin in each power supply cable end, like the picture below: Figure 25-5. Connector soldered Next, isolate parts soldered in a way that pins don’t touch themselves when installed in connector. The detail is shown below: Figure 25-6.
PAGE 107
Chapter 25. Installation Guide Next, plug pins inside connector. Pins should be inserted behind the connector until the hang plug, setting pins like the picture below: Figure 25-7. Cable disposition - Front view 1) Return (0V) 2) Ground 3) Phase (-48/-60Vdc) Finally, build the cape around the connector. WARNING: "Observe wires disposition in connector, see picture above." 25.3. Installing the FAN Module in the Chassis Push the FAN module by the screws shown in red circles.
PAGE 108
Chapter 25. Installation Guide Figure 25-8. FAN Module Installation 25.4. Removing the FAN Module of the Chassis Pull the FAN module by the screws shown in red circles. WARNING: "The FAN module takes a few seconds to completely stop.
PAGE 109
Chapter 25. Installation Guide Figure 25-9. FAN Module Removal 25.5. Inserting the Interface Board in the Chassis The following picture ilustrates the correct insertion of a DM4000 interface module into the DM4004 or DM4008 chassis.
PAGE 110
Chapter 25. Installation Guide Figure 25-10. Step 1 - Ejector levers should be located to rabbet in chassis Figure 25-11.
PAGE 111
Chapter 25. Installation Guide Figure 25-12. Step 3 - Press the ejector levers to chassis 1. Ejector levers should be located to rabbet in chassis 2. Ejector levers should be located after the board 3. Press the ejector levers to chassis After the interface board is properly inserted in the chassis, tighten the knurling screws as shown in the following picture. Figure 25-13.
PAGE 112
Chapter 25. Installation Guide 25.6. SFP Module 25.6.1. Connecting a SFP Module The use of a SFP transceiver is optional. It is not included in the package. Follow the next instructions to install a SFP module properly: Figure 25-14. Connecting an optical SFP Module in an interface board 1. Insert the SFP transceiver into any of the switch module bays. There’s only one orientation that the module can be plugged. The optical connector should face outward.
PAGE 113
Chapter 25. Installation Guide The SFP modules that can be used with DM4000 Series Switches and each respective maximum fiber length are described in the table below: Table 25-2. Gigabit SFP Modules SFP Module Fiber Type Maximum Length 1000BASE-SX multimode 550m 1000BASE-LX singlemode 10km 1000BASE-LX+ singlemode 30km 1000BASE-LH singlemode 80km 1000BASE-LZ singlemode 120km "These modules are the most used. Contact technical support for the complete and updated SFPs module list.
PAGE 114
Chapter 25. Installation Guide 1. Remove the fibers 2. Release the security locker 3. Pull off the module through the locker 25.6.3. Transceivers Homologation Check DATACOM transceivers are tested to comply with IEEE802.3z and LASER safety standards. Non-homologated transceivers do not guarantee compliance and may damage the Interface Board hardware. DATACOM’s software checks for homologated transceivers before starting traffic and blocks non-homologated transceivers.
PAGE 115
Appendix A. Cable DB9-RJ-45 A.1. Construction To build a cable DB9-RJ-45 you need to connect the pins shown in the below, this cable will serve to command the MPUs and standalone chassis by serial port. Also, see the pins in the next pictures. Figure A-1. RJ-45 Pins Figure A-2.
PAGE 116
Appendix A. Cable DB9-RJ-45 Table A-1.
PAGE 117
Appendix B. Optical Amplifiers B.1. How to connect an optical amplifier and a interface board An optical amplifier board is used to amplify a transmission signal that will travel a long distance, in that way avoiding data loss during the course. The EDFA (Erbium Doped Fiber Amplifier) based boards can be used with 1G or 10G ports and operate with wavelenghts of 1530nm at 1562nm.
PAGE 118
Appendix C. Applicable Standards C.1. Applicable Standards for DM4000 family Table C-1.